Question about 2001 Isuzu Trooper

1 Answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper

Need the torque settings for the fixing bolts in the fly wheel

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Isuzu Master
  • 450 Answers

Diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

Posted on Jul 27, 2009

  • Tony Ryan
    Tony Ryan Jul 26, 2016

    Thank you. Very helpful

  • Tony Ryan
    Tony Ryan Jul 26, 2016

    Should the release bearing have play on the pressure plate?

×

6 Suggested Answers

  • 54 Answers

SOURCE: dual mass fly wheel

its the wrong flywheel the sensor pick ups on the back of it are different

Posted on Mar 28, 2010

  • 375 Answers

SOURCE: Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Posted on Jul 01, 2008

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 2 Answers

SOURCE: what is the 98 isuzu rodeo head bolt torque

joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Posted on Sep 01, 2008

stormbrewin
  • 426 Answers

SOURCE: isuzu trooper problem!with a 00 3 litre diesel engine not starting

Was it lined up right as the trigger point for the sensor is important.Is the fly wheel fitted one position only that the bolt holes line up or will it fit no matter which position it bolts up Line up the flywheel trigger with the sensor after you have put the engine to Top Dead Centre.Put at tdc and see if the trigger and sensor are together.

Posted on Oct 18, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 XL-7 Grand Vitara do they come standard with a dual mass flywheel and if so I need the torque settings for flywheel,and clutch pressure plate your help would be much appreciated Darren


which engine?\
1.6L G16
2L (j20 )
2.5L H25, H27? what?
ill try to guess, car is USA?
most are H25 v6
the book is clear, you can log in to mitchels and read too..

fly to crank, 51ft/lbs
PP bolts.?
step 3 , states Then tighten bolts to 17 ft. lbs. (23 Nm).
for real answers, using real books, the suzuki book is only 4bucks. to read
here
(all above is off clone , online books, not below which is real.

https://suzukipitstopplus.com/Category/3-suzuki-service-manuals.aspx

i never build engine off net rumors....

Jun 07, 2016 | Suzuki Grand Vitara Cars & Trucks

1 Answer

Isuzu trooper 2004 model 4jx1 engine what was the fly wheel marks if it was at tdc


if flywheel is fitted in correct position the timing mark on the front top cambelt gear is at 12 O clock and with starter motor removed you will see 3 lines stamped in the interuptor ring that is bolted to the rear of the flywheel if manual on early builds, also there is a notch in flywheel which you can see if gearbox is out this goes at 6 O clock
25312290-55d4lqh0wtq3cergg12nnjcv-3-0.jpg

Dec 07, 2014 | Isuzu Cars & Trucks

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

2 Answers

Isuzu 3.0 trooper no drive when in gear pressure


hi found out that it is a dual mass flywheeel and its allowing this problem as its faulty

Nov 17, 2009 | 2000 Isuzu Trooper

1 Answer

Settings on engine


WHAT SETTINGS DO YOU NEED TO KNOW WHEN CHANGING THE FLY WHEEL IS IT TORQUE OR ALLIGNMENT

May 10, 2009 | 1999 Isuzu Trooper

2 Answers

Fly wheel problem on a jeep


if its a 4JX1 diesel, yes it goes in 1 spot yet it can be bolted up in every location
put crank pulley timing mark to TDC can also check by removing cam belt top cover and check timing mark aligned up with mark at 12 O clock then flywheel has small notch in edge that must go at 6 O clock (facing down) look closely it is hard to see due to flywheel sunk into back of block.

Oct 19, 2008 | 2000 Isuzu Trooper

1 Answer

Isuzu trooper problem!with a 00 3 litre diesel engine not starting


Was it lined up right as the trigger point for the sensor is important.Is the fly wheel fitted one position only that the bolt holes line up or will it fit no matter which position it bolts up Line up the flywheel trigger with the sensor after you have put the engine to Top Dead Centre.Put at tdc and see if the trigger and sensor are together.

Oct 18, 2008 | 2000 Isuzu Trooper

2 Answers

Isuzu trooper 3 litre diesell oo year!


with no1 at TDC mark is on balancer and can take off top cam belt cover to check that cam gear is timmed on mark at 12 O clock there is notch in edge of flywheel that should be put at 6 O clock (facing down) it is hard to see with flywheel on engine look closely

Oct 18, 2008 | 2000 Isuzu Trooper

Not finding what you are looking for?
2001 Isuzu Trooper Logo

1,331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

71162 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...