Question about 1995 Nissan Pickup

Open Question

Show picture of clutch fork ,the throw out bearing

Toyota workmate 2004 hilux ute two wheel drive petrol

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

duane_wong
  • 6826 Answers

SOURCE: what is needed to remedy right hand front wheel

replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.

  1. Raise the front of the truck and support it with safety stands. Remove the wheels.
  2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
  3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
  4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
  5. Pry the inner oil seal out and remove the inner bearing. To install:
  6. Clean and inspect the bearings and outer races.
  7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
  8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
  9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
  10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
  11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
  12. Install the lock-nut, new cotter pin and hub grease cap.
  13. Install the brake torque plate. Install the brake caliper.
  14. Install the wheels and lower the truck.
4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT
  1. Thoroughly clean all parts and pack the wheel bearings.
  2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
  3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
  4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
  5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
  6. Turn wheel hub several times in both directions.
  7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models 86718030.gif
    Fig. 2: Removing the bearing outer races 86718032.gif
    Fig. 3: Packing the wheel bearing with grease 86718033.gif
    Fig. 4: Pack the lip cavity of grease seal with grease 86718034.gif
    Fig. 5: Exploded view of the front axle assembly — 4wd models 86718031.gif

  8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
  9. Install lock washer by tightening the lock-nut within 15–30 degrees.
  10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
  11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.
prev.gif next.gif

Posted on Jul 28, 2010

  • 123 Answers

SOURCE: for the first gear there

not sure it come from the clutch... do you check your engine/gearbox mounting?

Posted on Nov 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New battery - battery is drained in the morning.Replaced voltage regulator. Disconnected aircon. Still drains overnight. Ute will start and run with full battery but it drains overnight.


Easyest thing to do is pull one cable off your battery. Start pulling fuses and each time touch the cable to the battery post. When you find one that reduces the spark drastically that is the circuit to investigate.

Jan 06, 2017 | Toyota Cars & Trucks

1 Answer

Engine won't start, will clutch but no key.


Neutral safety switch? At the clutch pedal.

Oct 29, 2016 | Toyota Hilux Cars & Trucks

1 Answer

I'm looking for cruise control for 06 B4000 Mazda


the best brand is commodore brand and they have a huge range to suit most every vehicle
I have one fitted to a toyota hilux and it is warranted as well as the vehicle itself It is a toyota recommended after market fit as the hilux (workmate ute) is not factory fitted with a cruise control
I self fitted the same brand to a mazda b2600 ute and it was faultless fir the time I had the vehicle
can be obtained from commodore on line or from off road shops

Aug 31, 2016 | Mazda Cars & Trucks

1 Answer

Can anyone please assist me? I'm looking for the specs on the 2.7 vvti hilux raider d/c


Herman, Google search your year,make and model# specifications or manual. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Toyota Hilux Wikipedia the free encyclopedia
Hilux facelift driven in Bloem
http://www3.toyota.com.au/hilux/specifications/workmate-4x2-single-cab-cab-chassis-4-cylinder-petrol-manual

Aug 22, 2016 | Toyota Cars & Trucks

2 Answers

Just bought a 2004 Elantra (93000 miles) with 5 speed tranny. With the hood up and my daughter behind the wheel I noticed a rattling sound (in neutral) coming from the clutch/transmission area when the...


I would be checking the throwout bearing. But, if the clutch isn't slipping, maybe leave it for now?

If you put it in 5th gear, let out the clutch with handbrake applied and it stalls--the clutch isn't slipping for sure.

Jan 31, 2011 | 2004 Hyundai Elantra

1 Answer

HI, I own a 1997 Toyota Rav 4 4 wheel drive 4 cyl, the other day it started to make this loud noise coming from the front sounds like a grinding noise, when you put the clutch in the sound goes away any...


it sounds like it is either your clutch or the throw out bearing. either way you more than likely need to have to install a complete clutch kit (pressure plate, clutch disc, throw out bearing, and have your flywheel resurfaced.

Nov 19, 2010 | 1997 Toyota RAV4

1 Answer

I need to adjust the clutch on a 1995 standard mighty max mitsubishi I changed the clutch disc, pilot bearing, throw-out bearing and pressure plate, but the clutch stays against the fly wheel when running...


You will need to turn the cable adjuster so there is only about 1/8 inch of free travel of the cable where it attaches to throw out fork before it starts to move the fork. Once the throw out bearing is achieving its full travel the clutch should release and enable gear selection.

Don't forget to rate this post !!

Oct 11, 2010 | 1995 Mitsubishi Mighty Max

1 Answer

Tapping noise on start up then fades away all together within 30-40 seconds, could this be wrong verosity oil or? 2004 workmate 2.7 petrol hilux


The tapping is normal at start up, and is caused by lack of oil at the top of engine. The sound goes away within the time frame you stated (30-40 seconds). You have nothing to worry about.

Jul 05, 2010 | 2004 Toyota Tacoma

1 Answer

Truck makes loud noise unless clutch is pushed in


chances are the adjustment of the throwout bearing fork is the problem . because of vibration that is the rattling that you are hearing. correct adjustment should be as follows.

#1...peddle travle should be no more than 1 1/2 inches

#2...the clearance between throw out bearing and fork no more than 1/2 inch

#3...clearance between fork and fork stops is 1/8 inch

also there should be grease zerts in the shaft that holds the fork and linkage make sure they are not dry of grease...please rate the solution....thanks

Sep 22, 2008 | 1987 Toyota Pickup

Not finding what you are looking for?
1995 Nissan Pickup Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...