Question about Cars & Trucks

Open Question

How to change rear turn signal bulb of a 2007 pontiac G7

How to change rear turn signal bulb

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75066 Answers

SOURCE: Replacing rear turn signal bulb in 2003 Mustang

remove the trim panel at the very rear of trunk, remove it and place it out of the way, remove tail light Assembly retaining nuts top and bottom, I think there are 6 per side, pull the tail light assembly straight back to access the bulbs for replacement.

Posted on Dec 04, 2008

  • 1 Answer

SOURCE: real right turn signal light - Pontiac Montana SV6 2005

If the 2005 Montana is similar to the 2001 Montana, I have a solution. First you'll need a hexagonal wrench (the 6-sided L-shaped wrench). The tail light assembly is held on by two screws. You'll need the hexagonal wrench to remove them, because a normal screwdriver won't do it. I also had to use a conventional adjustable wrench to get the leverage to turn the hexagonal wrench, because the screws were in there pretty tight. Once you remove the two screws, the whole tail light assembly should come off. Mine required a little force and I had to play with it a bit, but it came off without a lot of work. There will be one set of wires that connects the tail light assembly to the rest of the minivan--try not to damage that set of wires. Once you get the tail light assembly off, you'll have to take apart the assembly that actually holds the lights. No tools should be required. It's held on by four plastic catches. Just undo the catches (easier said than done, but still not too tough) and it comes apart. Then you can pop out the old light and pop in the new light. Then re-assemble. For me, it went back together much easier than it came apart.

Posted on Jan 03, 2009

motor1258
  • 6674 Answers

SOURCE: I have a 2007 Dodge Grand Caravan and the right

Usually that fast blink is a good warning that one of the signals is out. Double checked that bulb is same # and all that ? What number is on the bulb? if it's 2057 or 3057, try pulling wires on side of bulb with fingernail, outward to make better contact, to see if that helps.

Posted on Mar 07, 2009

  • 120 Answers

SOURCE: 2007 ford 500 rear turn signal bulb replacement

This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Posted on Jan 23, 2010

  • 57 Answers

SOURCE: 2004 Pontiac Grand Prix GTP front pass turn signal doesn't work

you would need to buy a blinker relay

Posted on Jul 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing the rear turn signal bulb


Some bulbs are really tough to remove on this car. Specially the front side lights. You have to first remove the panel in front of the tires. Hope this helps.

Apr 04, 2014 | 2007 Chevrolet HHR Fall

2 Answers

2007 chevy impala brake light and left turn signal not working


Fast flashing dash signals mean there is a bulb issue-DEFINATELY!

Aug 07, 2012 | 2007 Chevrolet Impala LS Sedan New Cars

3 Answers

I just noticed lately when I turn ON my turn signals, they start blinking twice normal then starts blinking really fast. And not all the rear light bulbs are ON. Could this be my turn signal...


If one of your rear bulbs is burnt out then the signals will react this way. 2007 is not very old of a car for a signal delay problem. It would be more likely a bulb.

Mar 01, 2011 | 2007 Ford Mustang GT California Special...

1 Answer

Turn signal is blinking fast. Brake light not working. Is it a fuse or do I need to change the entire bulb??


Turn signals sometimes blink fast when bulbs are burnt out-change bulb and you shuld be fine.

Feb 05, 2011 | 2007 Pontiac G5 Gt Coupe

1 Answer

How do I change the rear turn signal bulb on my 2007 pontiac g6 convertible


Probably too late for you, but others may benefit as I just did this.
In your trunk on each rear side panel, you will find several rubber stoppers approximately 1" wide. take a flat head screwdriver and pry underneath to loosen then pull the stopper out.
Take a socket set you and find the right size socket for your nut and take out the 2 nuts on top and the bolt at the bottom (my bottom bolt didn't have a stopper on it).
Pull out the tail light assembly. Remove the bad bulb from the back of the assembly and replace with a new bulb (look up type of bulb to buy in your owners manual). Replace hardware and test lights.

Dec 26, 2010 | 2007 Pontiac G6 GT Convertible

1 Answer

Driver front turn signal does not blink. front


This may have more then one bulb in the front or possibly a bad socket try wiggling the new bulb in the socket to see if it will work.Compare all turn signal lights that come on the passenger side to those drivers side.Some vehicles also incorporate sidemarker lights with the turn signals.

May 29, 2010 | 2001 Pontiac Aztek

1 Answer

How to change a turn signal on a 2007 impal


Open the trunk, inside the trunk is a liner. Pull the liner back and you'll see the wiring going to the back of the light. Remove the light bulb retainer by unscrewing it and change the bulb.

Apr 02, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

1998 pontiac transport/montana has not tail or break lights...turn signals blink fast or not at all. changed rear bulbs and noticed carbon on front build up on front bulbs. Help!


If one of the filaments in the bulbs is burned out, the remaining working lights will flash alot quicker.
Check the bulbs, and replace if the filaments are broken.
If the front bulb has a carbon build up it blown out...change it..
Once the bulbs are replaced your signals should work properly.

Dec 09, 2009 | Pontiac Trans Sport Cars & Trucks

1 Answer

2007 ford 500 rear turn signal bulb replacement


This is straight from the owner's manual.

#1 Make sure the headlamp switch is in the OFF position and open the trunk.
#2 Carefully pull the carpet away to expose the backside of the tail lamp assembly.
#3 Remove the nut and washer assemblies, then pull the lamp assembly away from the vehicle.
#4 Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly.
#5 Pull the bulb straight from the socket.

Install new bulb(s) in reverse order.
Good luck

Apr 01, 2009 | 2007 Ford Five Hundred Limited Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...