Question about 2005 Citroen C8 2.0

Open Question

How do you bleed a Citroen c8 hydraulic clutch

Special tools needed

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

npwright174
  • 1 Answer

SOURCE: Citroen C8 totally dead

sounds like an earth problem, check the earth cable to the engine.

Posted on Apr 09, 2012

  • 80 Answers

SOURCE: citroen c8 not charging battery

Kindly run a scan.

Posted on Apr 13, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch , presure plate and gearbox remove


You need the right equipment and knowledge to do this job there are a lot of cables wires etc that need to be removed before the gearbox can be loosened and removed.
There are also a lot of special tools required and the job is best done on a ramp or pit to gain access.
Trying to do this on the ground would be difficult and very dangerous also the engine needs to be suspended when the gearbox mounts are removed.
It is impossible to remove the clutch pressure plate, plate and hydraulic bearing on the C4 without removing the gearbox.
Take it to a garage/ clutch specialist.

Dec 26, 2013 | Citroen C4 Cars & Trucks

1 Answer

Where is the slave cylinder on 91 gmc sierra


I had a 92 Chevy Cavalier which had the hydraulic clutch system like yours. I had intended to flush and purge the hydraulic clutch system at the same time I flushed and purged the brake system. I traced the hydraulic lines from the master cylinder into the front of the transmission where the clutch is located. This is the most likely place to look for the slave. I didn't find a way to bleed the lines with the transmission still in and the Hanes manual I had was unhelpful. The dealer told me it was a "special job" that had to be done in a shop.

Oct 04, 2012 | Cars & Trucks

1 Answer

Citroen C8 totally dead


sounds like an earth problem, check the earth cable to the engine.

Apr 09, 2012 | 2005 Citroen C8 2.0

1 Answer

How to bleed clutch


You will need a vacuum clutch bleeding tool, they are made my a company called "MITYVAC", inquire at your local NAPA or Carquest auto parts store, Autozone may carry them as well. Without a bleed due to the design of the clutch hydraulic circuit it is nearly impossible to get all the air out.

Dec 23, 2011 | 2003 Ford E150

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

Bleeding brakes, The front brakes will not bleed out


In order to bleed the brakes on this car u need a special tool that holds the ABS Hydraulic control units pop-it valves open, without this special tool that plugs into the ABS you can't bleed the air out of the ABS control valve module, u either have to have the dealer do this or someone who has a factory equivalent of the ABS special bleeding tool, Snap-On tools most likely makes these, they are horribly expensive.

Mar 30, 2010 | 1996 Land Rover Discovery

1 Answer

1994 Altima clutch master and slave replacement


easy replace both parts then fill the clutch reservoir,crack slave cly bleeder to let gravity bleed let 1 to 2 reservoirs flow through,tighten bleeder and pump clutch pedal,pump 4 or 5 times hold down pedal get 2nd person to crack bleeder while pedal is down,tighten bleeder before releasing pedal,should work fine

Nov 04, 2009 | 1994 Nissan Altima

1 Answer

95 pontiac firebird. 8th vin S 10th vin S . new


bleeding this clutch requires a special tool, take it to the dealer.

Aug 04, 2009 | Pontiac Firebird Cars & Trucks

Not finding what you are looking for?
2005 Citroen C8 2.0 Logo

Related Topics:

91 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citroen Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14228 Answers

Are you a Citroen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...