Question about 2002 Hyundai Accent

2 Answers

Removal of disk brake

Have a 2002 hyundai accent. Trying to figure out how to remove and replace the front brakes.. help asap

Posted by on

  • Anonymous May 18, 2009

    1998 hyundai accent how do i change front brake discs

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Go to halfords and buy a haynes manual it will explain step by step on how to do this

Posted on Jan 19, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 98 Answers

Post is a month old but maybe someone else will read it and get the information. This is actually very easy. Make sure the parking brake is set and remove the wheel of whichever side you are working on. The calipers on this have one bolt on the top that needs to be loosened. Once the top bolt is loosened you will need to pull up on both sides of the caliper to disengage it from the brake pads/rotor. Once it is disengaged it is best if you have something available to tie it off for the moment so it does not just hang as that can damage the brake line. Once you have the caliper pulled out of the way-if you are new to brake jobs familiarize yourself with the alignment of the brake pads. Each side is going to have an inner and outer pad. The pad that goes on the inside is the one that has the sensor, it is a metal clip attached to the bottom of the brake pad. Before you take the old pads out compare their position with your new pads. Using a screwdriver as carefully as possible pop out the old "outer" brake pad and put the new one back in its place. Doing only inner and outer one at a time will help with your brake hardware brackets at the top and bottom of the pads not falling/coming out of place. Then replace the inner brake pad. Once that is done what you are going to need to do is to push the caliper back in. This is done with what is called a C-clamp-medium or large size-available at most parts places. They will know what you are talking about. When you are looking at the caliper what you will notice is that in the middle it is protruding out. You need to push it back into the caliper so that it will fit the new brake pads. Put one end of the C-clamp on the edge of this protrusion and put the other end of the C-clamp on the back of the caliper. Turn the handle until it is taut and at that point it will be harder to turn but as you turn the C-clamp handle the caliper will begin receding until it is flush at which point you are ready to put the caliper back on. Put the caliper over the new pads and where you took the bolt out-you may have to push the caliper guide pin out slightly to put the bolt back in but it should be no real problem. Once you have tightened the top caliper bolt back up, put the wheel back on and do the other side. Once both sides are done before you drive the car you will need to make sure and start the car, and pump the brakes a few times so that the caliper can make firm contact with the new brake pads. After that you should be good to go

Posted on Feb 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace front wheel bearing in a 2008 hyundai accent?


Hi there, I think from memory the whole hub assembly comes with new bearings when you replace it, it's a easy change, remove wheel, remove the brake calliper, remove the front axel nut and the hub should come off, hope this helps, it's a easy change

May 19, 2014 | 2006 Hyundai Accent

2 Answers

I have an 2006 Hyundai Accent Atlantic and I would like to know if front brakes have pads and rear brakes have shoes


2006 Accent Brakes, Suspension & Handling Specs • Four-wheel ABS • Four disc brakes including two ventilated discs • Electronic brake distribution • Spacesaver steel rim internal spare wheel • Strut front suspension independent with stabilizer bar and coil springs , torsion beam rear suspension semi-independent with stabilizer bar and coil springs

Read more: http://www.automotive.com/2006/12/hyundai/accent/specifications/handling-ride-braking.html#ixzz1JcYuzhff

Apr 15, 2011 | 2006 Hyundai Accent

1 Answer

How to replace the third brake light (hatch) on a 2005 hyundai accent. I took off the 4 screw on the the plastic cover and it still won't come off. Tried taking off cove of back hatch but don't want to...


Above the third brake light is a small panel, remove this panel using small screwdriver.
1. You'll see four (4) bolts, remove the three bolts that are painted black, do not remove the center bolt holding the plastic molding, this is for the door molding, and has nothing to do with the light.
2. Once those three bolts are out, you'll see two more small screws, remove them and you'll have access to the third brake light bulb.

Be careful when pulling out the bulb, my bulb broke, and I'm still trying to get pieces out! - Good luck.

Jan 16, 2011 | 2005 Hyundai Accent

1 Answer

Replace front brake pads


Losen your lug nuts on both front tires and jack up the front end. You need to remove the calipers (the piece that holding the brake pads) Two bolts behind the caliper. Pop the the brake pads off and depress the brakes ( you will need a clamp to depress it) Put on the new brake pads. Tools needed : clamp, flat head screww driver, soket set, brake cleaner

Jan 20, 2010 | 2000 Hyundai Accent

2 Answers

Change hyundai accent 2001 front brake pads


may have siezed caliper slide pins suggest buy reman loaded caliper assembly

Oct 05, 2009 | 2001 Hyundai Accent

3 Answers

How do i change the front brake pads


First make sure you have the park brake on
Raise the front end make sure to support with jack stands
Remove tires

this should leave the front brakes exposed

there are two slide bolts holding the caliper in place loosen both and remove

then wedge a screw driver between the inner pad and the rotor and lightly pry towards you to take some pressure off of the caliper

you should now be able to lift off the caliper it will still have the brake line attached to it so be sure to secure it to something ie a bungie strap to the suspension or something do not just let it hang by the brake line

slide out the old pads out of the caliper mounting braket

now take a caliper press and push the piston back into the brake caliper use the old inner pad do not push directly on the caliper piston (if you dont have a caliper press just substitute a c clamp it works fine)

if replacing the rotors remove the caliper bracket once again two bolts

remove the caliper bracket

remove rotor

Make Sure to inspect the caliper for leaks or damage

To install reverse and youll be done before you know it

Make sure to lube slide pins with a small amount of brake grease and make sure the caliper moves freely apon installation

After you have done both sides

set down car and slowly pump the brake pedal about 15 times to close the distance between caliper piston and brake pads thats all

I hope this helps

Jan 22, 2009 | 2002 Hyundai Accent

1 Answer

2002 hyundai accent needs brakes


hi from uk to renew front disc(rotors) and brake pads on the accent are not beyond the mech minded diy er and can easilly be done if you follow instructions on the haynes manual etc and would save$$$$s in dealer charges ? if you diy as for the rear brakes they are drum brakes with shoes that are auto adjust but again can be done by diy with help of manual ? as for cost of parts ? you can obtain/price of all parts from good auto shop/superstore also a manual ? then by all means obtain a quote ? for local garage to do the brakes with cost of labour and parts ? then consider option of diy? i am sure you will be tempted/inspired if you browse the work involved hope this helps? contact again if you feel lucky? will be glad to assist if you get stuck? or req info ? merry xmas from uk

Dec 19, 2008 | 2002 Hyundai Accent

1 Answer

2002 Hyunsai Accent rear brakes, do you have to remove wheel hub


Yes, it should be removed it makes the job a lot less difficuilt. 

Nov 30, 2008 | 2002 Hyundai Accent

Not finding what you are looking for?
2002 Hyundai Accent Logo

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...