Question about Cars & Trucks

Open Question

How to remove headrest from 2000 Lincoln town car

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 lincoln ls heater not working...thermostat?

- If temp guage reads normal, the lack of heat may be due to the Heater Control Valve. Located in front of the radiator. Lower passenger side. A real bugger to replace.
- The plastic cap just over the thermostat is key in re-filling the anti freeze and bleeding air.

Posted on Dec 25, 2008

  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

old marine
  • 1917 Answers

SOURCE: need routing diagram for 2000 lincoln town car serpentine belt

There's a diagram at this link.

Posted on May 11, 2009

bschilz
  • 2049 Answers

SOURCE: i need the serpintiine belt diagram for a 2000

Here you go... 2000 Lincoln Towncar belt routing diagram.

1b31ff9.jpg

Posted on Oct 26, 2009

kennyz195
  • 61 Answers

SOURCE: 2003 Lincoln Town Car - Power window switch removal/installation

SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.

  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the front seat headrests from a 92 Lincoln Towncar with a split bench seat? Thank you


you should be able to pull up on the headrest and it should come out there might be a little button on the headrest bracket that the rods fit into that you would press in if not just pull straight up with some force also try spraying some W D-40 or PB blaster to loosen the rods in the tracks so you can pull up on them GOOD LUCK!STEPHEN

Jan 24, 2015 | 1992 Lincoln Town Car

1 Answer

How to remove a front bumper on a 2000 Lincoln town car


I would first google it looking for a U- Tube How To video?

Dec 16, 2014 | 2000 Lincoln Town Car

1 Answer

Cant remove the fron headrest on my 1992 lincoln town car


If you have 2 metal rods for the head rest the at the base of the rods in the moulding on the seat back there will be a press button that allows the rod locks to open and allow the head rest to be pulled straight up at the same time.

Jan 03, 2014 | Cars & Trucks

1 Answer

Remove third row headrest


Pull the headrest up toward the ceiling as far as you are able. There is a small plastic button on the side of one of the metal mounting rods (that go down into the seat). Depress and hold the button and pull up again. The headrest will come right out.

Jul 04, 2013 | 2012 Chrysler Town and Country

1 Answer

Heater core replacement in a 2000 lincoln town car


remove the whole dash to get the heater unit out ,sorry no short cuts available

Jan 28, 2012 | 2000 Lincoln Town Car

1 Answer

Hi i have 2000 lincoln town car.could u please let me know is there any other lightng cntrol module number that I could use instead of XW1T-13C788-AB. for a 2000 Lincoln Town Car? thank you


this is an engineering part number off the part. not the service number.
the service numbers you can use are yw1z-13c788-BA or YW1Z-13C788-AA, or XW1Z-13C788-AA.

However, Gino on ebay fixes these for $175. Go to ebay and type in the serach box LCM Lincoln town car, and you should find him. He is is California.

Good luck.

It's under the dash above the steering column. remove sound cover for access.

Jul 29, 2011 | 1999 Lincoln Town Car

2 Answers

2000 lincoln town car executive series sparkplugs


Between the rocker cover and the fuel rail are the coils, one per cylinder hed in place by a smill 8mm bolt. Remove the coil and find the spark plug wire, the arrangement is called a coil-on-plug or COP. Spark plug is in the tube from whince the spark plug wire came. 5/8" deep socket and long extension will reach it. Another hint find some way to clean out the tube before removing the spark plug least all kinds of junk winds up in the cylinder.......SMith

Jun 19, 2009 | 2000 Lincoln Town Car

1 Answer

Led radio station indicator light out on a lincoln town car


Most likely not. In order to replace the bulb you will have to remove it from the dash.

Mar 11, 2009 | 2000 Lincoln Town Car

3 Answers

Removal of headrest on 2005 Ford F150.


The headrest has on obvious button to adjust the height and another button kinda hidden to remove the headrest. The black plastic ring at the base where the metal poles insert into the seat is where the two buttons. You probably noticed the obvious on that sticks out of the side of one of the rings. The other plastic ring contains a similar button that is not noticeable due to it being flush with the side of the plastic ring. Adjust the headrest to its highest position, then locate the "hidden" button on the other plastic ring and depress it while lifting on the headrest and it should come out.

Dec 11, 2008 | 2005 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...