Question about Lincoln Continental

1 Answer

Remove shift lever - Continental Lincoln Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 76,132 Answers

It has a roll pin that holds it on, remove it with a hammer and small drift punch

Posted on Oct 30, 2012

  • phillyitalia
    phillyitalia Oct 31, 2012

    so after i pop up the trim and pop out the shift indicator assembly to expose the lever i remove the 2 bolts closest to me and remove the 2 torx bolts that are under where the ash tray are then remove the roll pin and it should come loose ?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I REPLACE SHIFT CABLE


rtm? no symptoms so i must guess, ill say , cant shift. and is not park lock out causing that.
want to read the manual or me to you.'?
ill guess you.

http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

click 1996 to 2001
it replaces like all cables do
detach both ends and remove it. if clamps seen those too.
what matters is adjustment is needed.

some have 2 cables, one to gear box and one to ignition switch.
Chapter 21, page 150 states
REMOVAL
(1) Shift transmission into Park.
(2) Remove shift lever bezel and necessary console
parts for access to shift lever assembly.
(3) Disconnect cable at shift lever and feed cable
through dash panel opening to underside of vehicle.
(4) Raise vehicle.
(5) Disengage cable eyelet at transmission shift
lever and pull cable adjuster out of mounting
bracket. Then remove old cable from vehicle.
INSTALLATION
(1) Route cable through hole in dash panel. Fully
seat cable grommet into dash panel.
(2) Place the auto transmission manual shift control
lever in "Park" detent (rearmost) position and
rotate prop shaft to ensure transmission is in park.
(3) Connect shift cable to shifter mechanism by
snapping cable retaining ears into shifter bracket
and press cable end fitting onto lever ball stud.
(4) Place the floor shifter lever in park position.
Ensure that the pawl is seated within the confines of
the adjustment gauge clip.
(5) Snap the cable into the transmission bracket so
the retaining ears are engaged and connect cable end
fitting onto the manual control lever ball stud.
(6) Lock shift cable into position by pushing
upward on the adjusting lock button.
(7) Remove and discard the shift cable adjustment
gauge clip from the park gate of the shifter.

easy?

Aug 25, 2015 | 1996 Jeep Cherokee

1 Answer

I have a 02 saturan l200 and the shift stick broke off from place where the gears are. I know it sounds confusing but I don't know the name of all the parts. Can anyone help me


Pull up on the shift lever boot to disengage from the console. The shift lever boot is rubber or leather or some other material !
Using a small screwdriver, remove the lever assembly retaining clip.
Remove the lever assembly ! I know this may sound complicated but it's real easy ! The shift leaver goes to a shift linkage that goes to the gear box !

Mar 06, 2015 | Cars & Trucks

2 Answers

Why is it hard to shift gears on my 1997 lumina.


if the shift process is through a cable then check the cable for wear and fraying, rust or dry. If it is through linkage check for worn /rusted /tight connections

Nov 13, 2014 | 1997 Chevrolet Lumina

1 Answer

Brake shift interlock solenoid


column or floor shifter ?
Brake Shift Interlock Actuator - Floor Shift Removal and Installation
NOTE: The brake shift interlock actuator is not serviced individually. If replacement is required, install a new floor shift selector lever assembly.
For additional information, refer to Selector Lever - Floor Shift in this section.
Brake Shift Interlock Actuator - Column Shift Removal and Installation
  1. Set the parking brake.
  1. Remove the steering column shrouds.
  1. Turn the ignition to the accessory position and apply the brake or actuate the brake shift interlock actuator (BSIA) override.
  1. Put the selector lever into the NEUTRAL position.
  1. Disconnect the BSIA electrical connector.
  1. Remove the BSIA screw.
  1. Gently pry the clip up and remove the BSIA.
  1. NOTE: During installation, verify that the BSIA override has been activated and the slider is fully rearward. Before rotating the selector lever from NEUTRAL into PARK, align the selector lever tab into the BSIA. To install, reverse the removal procedure.

May 26, 2017 | Ford Expedition Cars & Trucks

1 Answer

How do you remove the manual shift lever from a 1994 acura legend


YOU HAVE TO UNSCREW THE SHIFT LEVER KNOB. REMOVE THE CENTER CONSOLE.REMOVE THE RUBBER SHIFT LEVER BOOT AND THE DUST SEAL.YOU NEED TO RAISE SUPPORT VECHICLE ON JACKSTANDS ON LEVEL SOLID GROUND.YOU HAVE TO DISCONNECT THE EXTENSION ROD FROM THE TRANSAXLE.SIMPLY REMOVE THE BOLT THAT ATTACHES IT TO THE EXTENSION BRACKET.TO DISCONNECT THE SHIFT ROD FROM THE TRANSAXLE PUSH THE DUST BOOT FORWARD REMOVE THE CLIP AND DRIVE OUT THE SPRING PIN WITH A PIN PUNCH.DISCARD THE SPRING PIN.DO NOT REUSE IT.TO DISCONNECT THE REAR END OF THE SHIFT ROD FROM THE SHIFT LEVER REMOVE THE NUTS AND BOLTS.THEN REMOVE THE TWO NUTS AND WASHERS THAT RETAIN THE CHANGE BALL HOLDER TO THE UNDERSIDE OF THE EXTENSION ROD AND REMOVE THE CHANGE BALL HOLDER LOWER THE SHIFT LEVER DUST SEAL,SHIFT LEVER BALL SEAT,SHIFT LEVER AND EXTENSION ROD.INSPECT THE BUSHING AT THE FRONT END OF THE EXTENSION ROD AND REPLACE IT IF ITS CRACKED TORN OR WORN. REPLACE THE ORINGS IN THE BASE OF THE LEVER.BESURE TO LUBRICATE NEW O RINGS AND BUSHINGS WITH A SILICONE GREASE.USE A NEW SPRING PIN TO ATTACH THE SHIFT ROD TO THE TRANSAXLE.INSTALL EVERY THING BACK VISA VERSA.

Mar 02, 2011 | 1994 Acura Legend

1 Answer

Replace auto shift lever


You need to remove the shift handle first...key must be on...no need to start...pull shift lever down to low gear...look on the back side of the knob...you should see a u-shaped clip head...pry gently under the u-shape with a scredriver to begin removal...then use needle nose pliers to completely pull the clip out...after this is removed...you will be able to kift the shifter knob off...Don't know if you mean replace shift knob...(known for breaking) or actual metal shift lever...if you need the shifter arm, your best find would be at your local salvage yard...some will remove for you...some will let you find your model and remove yourself...To re-install put the shift knob back on the shift lever...to lock in place then re-insert the u-clip to lock in place...Many good mechanics are not familiar with removing these shift knobs...Hope this helps.

Feb 14, 2011 | 2001 Oldsmobile Alero

1 Answer

Trying to remove the stick shift from a 1992 toyota pickup to replace the clutch


REMOVE TRANSMISSION SHIFT LEVER FROM INSIDE OF VEHICLE
    • Remove the four screws and remove the shift lever boot retainer.
    • Pull up the shift lever boot.
    • Cover the shift lever cap with cloth.
    • Then, pressing down on the shift lever cap, rotate it counterclockwise to remove.
    • Remove the shift lever.
62409690

Jan 22, 2011 | 1992 Toyota Pickup

1 Answer

The 4 wheel drive shifter is broken. How does the linkage to the transfer case come apart?


Shift Lever NOTE: Remove the shift ball only if the shift ball, boot or lever (7E067) is being replaced.
Removal
  1. Raise vehicle on hoist and position suitable safety stands under vehicle.
  1. Prior to removing the control lever assembly (7E069), be sure the shifter is in the 2H position.
  1. Loosen (do not remove) the nut retaining the shift handle (7E067) to the control lever assembly (7E069). Remove the shift handle (7E067) from the control lever assembly (7E069).
  1. Remove the vent hose (7D494) from the notch in the detent plate.
  1. Remove the control rod (7A315) from the control lever assembly (7E069). ani_caut.gif CAUTION: When removing the control rod (7A315) off the control lever assembly (7E069), do so very gently so as not to damage the control lever assembly.
  1. Loosen (do not remove) the large pivot bolt holding the control lever assembly (7E069) to the detent plate.
  1. Swing the control lever assembly (7E069) out of the way and remove the two bolts (39129-S2) retaining the detent plate to the transmission extension housing. Remove the entire control lever assembly from the vehicle.
Installation
  1. Prior to installing the control lever assembly, be sure the transfer case link (7B106) is in the 2H position (pointing upward).
  1. Install the two bolts (39129-S2) to retain the control lever assembly (7E069) to the transmission extension housing and tighten to 92-125 Nm (68-92 ft-lb). Refer to the following illustration for bolt hole application.
  1. Attach the control rod (7A315) to the control lever assembly (7E069).
  1. Tighten the large pivot bolt to 92-125 Nm (68-92 ft-lb).
  1. Attach the vent hose (7D494) into the notch in the detent plate so the white mark is flush to the outside surface of the plate.
  1. Install the shift handle (7E067) into the control lever assembly (7E069). Tighten the retaining nut to 27-38 Nm (20-28 ft-lb).
  1. Check transfer case for proper shifting and operation.

    c10894a.gif



    cc10895a.gif

Feb 27, 2010 | 1992 Ford F250

1 Answer

How do you replace the shift lever shaft on a 06 yamaha ttr 230?


Yes. You need to remove the crankcase cover, oil pump, brake lever and clutch to remove it.

Sep 19, 2009 | 2006 Pontiac G6

1 Answer

Removal of gear shift knob


There are two types of shift knobs. One that unscrews and one that the lower trim of the shift knob separates from the knob using a trim stick. After separating the lower trim from the knob pull upward to release the knob from the shift lever. If a new shifter assembly is being installed, unscrew the original shift knob or separate the lower trim from the knob and pull up to remove the knob from the shift lever. Screw the knob onto the new shifter assembly's lever no more than 14 turns or install the lower trim onto the shift lever then push the knob onto the shift lever and install the lower trim piece onto the shift knob.

Jul 02, 2008 | 2007 Dodge Magnum SRT8 Wagon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...