Question about 2000 Buick Century

Open Question

Rear brake lines 2000 buick century

Rear brake line diagram

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jeffk14
  • 16 Answers

SOURCE: how to replace a coolant level sensor, 2000 buick century

TRY THIS. Good luck!

Posted on Nov 22, 2008

Ad
davidkay61
  • 23 Answers

SOURCE: buick century 2000 wipers

I found the following description on the web, this covers a bunch of the questions I was going to ask...

I own a 2000 Silo and wondered the same thing and do see some GM vans with this problem.

When I bought mine I also bought the Haynes Repair manual (1997 thru 2001 all models GM) #38036 to learn how to fix this and a LOT of other components in/on the van.

For $20 it's worth it.

To answer your question: If the wipers stop at the position they're in when the switch is turned off (Fail to park), disconnect the multi-function switch electrical connector. (This is located under the dash next to the firewall and steering column)

If the wipers now park, replace the multi-function switch. If the wipers still do NOT park, check the wiring from the wiper motor to the switch for a short circuit. If the circuits are good, replace the wiper motor.

Note: There are other adjustments needed for proper operation than just bolting and new motor on.

You can have a look at this manual at any automotive parts supply store.

Posted on Dec 06, 2008

Papa Chan
  • 56 Answers

SOURCE: how to replace a coolant level sensor, 2000 buick century

The coolant level sensor is located on the radiator. If you are looking at the engine from the front of the car it will be on the left side. There will some kind of clip holding it in the radiator. Removed the clip and pull the sensor out. You will lose coolant so try to swap it out quick or drain some of the coolant out. Once new sensor is installed, install clip to keep the sensor in place and reconnect the wires to the sensor. Crank the engine and make sure the coolant level is full. This should correct your problem.

Posted on Jan 04, 2009

  • 3 Answers

SOURCE: heater blowing cold air Buick Century 2000

does the car not heat up in general? Whats the temp gauge doing and how long of a ride have you tried this for?

Posted on Jan 06, 2009

  • 335 Answers

SOURCE: need buick century egr diagram

If your car runs bad with an EGR code then I would suggest that the EGR valve be replaced. I would like to know what code was set on your computer. It would help greatly. When the EGR malfunctions, you will have rough idle and possible stalling. If you have a code indicating EGR it may also condem the cat converter.Please show any codes that are set. Thanks Moe

Posted on Apr 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lincoln town car 1993 rear brake line diagram


The rear brake line should run down the left frame rail from the master cylinder to the rear of the car. It will terminate to a bulkhead reverse flare fitting into a rubber hose above the center of the axel differential cover, a tee fitting will tee the lines to each rear wheel backing plate, reverse flare fitting for wheel cylinder. If brake fluid is present (droplets) at brake drums, Replace the wheel cylinders.

Aug 13, 2017 | Lincoln Cars & Trucks

2 Answers

Master cylinder diagrams


the on from smaller chamber

Aug 15, 2014 | 1995 Chevrolet Camaro

1 Answer

Need a diagram for 2000 plymouth voyager brake lines


Diagrams are next to non existent

Have to duplicate what is there,always
been that way

Dec 02, 2012 | 2000 Plymouth Voyager

1 Answer

Rear brake line diagram for 2001 volkswagon


There are no brake line diagrams,never have been

A factory service manual may show a partial on some
line,but is of no value as to what you want

You have allthe original factory lines
If they are rusted out ,etc,you copy what
you have & bend,form or change as you see fit.

If you have some type of braking issue or problem
you need to provide details & the question

May 30, 2012 | 2001 Volkswagen Golf

1 Answer

My brakes are leaking in the rear driver side need a diagram of brake lines to folllow.


Follow the brake line starting at the left rear wheel, there is no diagram for brake lines, take the tire off and inspect (look) left rear wheel, It will be wet where the leak is, if the inside of the tire is wet then you might want to check the brake cylinder, behind the brake drum. You might want to take it to a shop and get it fixed, It is your life and others, if you can't stop.

Aug 05, 2011 | Ford Taurus Cars & Trucks

2 Answers

Diagram of the brake system. my brake system is leaking in the rear back end of the car, on the block that runs the lines to the different rear braks. I need to know the name of the block so I can replace...


It's a rear brake tee. Nothing but drilled brass. Might want to try checking the threads and flares on the brake lines that go into the tee. It's not often they crack and leak so inspect well. Let me know.

Jul 24, 2010 | 1996 Geo Tracker 2 Door

2 Answers

Leaking brake fluid from rear driver side brake lines,need a diagram of how to replace the lines. 1994 ford taurus 3.o v6.thanks


They don't make diagrams for brake lines. The lines are sold in bulk. You need to measure and duplicate the bends in the orignal lines and cut/flare the lines yourself. You will need a tubing cutter, flare tool and tubing bender.

Feb 27, 2010 | 1994 Ford Taurus

1 Answer

Brake line diagram


Brake Lines and Hoses
Double-walled steel line is used in the hydraulic lines between the brake master cylinder and the front tube connector, and between the brake master cylinder and the flexible brake hose at the rear wheels.
Double-flared brake lines provide good leak-proof connections.
When replacing hydraulic brake lines, hoses, or connectors, tighten all connections securely. After replacement, bleed the brake system; refer to Section 206-00 .
The wet appearance of the outer cover of the rubber brake hose is referred to as "sweating." This is a normal condition for neoprene rayon braid hose and is not a sign of leakage or cause for replacement of the hose.

Hydraulic Brake System Components — Non-ABS

dff7165.gif
Item Part Number Description 1 2005 Power Brake Booster 2 2455 Brake Pedal 3 2261 Rear Wheel Cylinder 4 2552 Rear Disc Brake Caliper— (Mexico Only) 5 2B120 Disc Brake Caliper—, Front 6 2B091 Brake Pressure Control Valves 7 2140 Brake Master Cylinder

May 02, 2009 | 1998 Mercury Tracer

Not finding what you are looking for?
2000 Buick Century Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...