Question about 1999 Volkswagen Jetta

Open Question

How to remove glove box 1999 VW Golf

Removing the 3 top screws and 3 bottom screws does not permit removal.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2000 vw golf how do I remove back hatch liner to

in each of those "holes" which are flanking the center hatch there is a screw in the bottom. remove those screws. then its pretty simple, yank out. the connectors to the actual hatch are in there really tight, so its kinda scarey on how much force you need to pull out. but it will just pop right out. be careful and keep a watchful eye out to where it connects to upper trim piece, it bends pretty easy... trust me i know

Posted on Mar 06, 2009

Ad
  • 10865 Answers

SOURCE: glove box lid golf mk4 2002

take it to any autozone. they will show u how to take it off and loan you tools to do it.

Posted on Apr 22, 2009

  • 1986 Answers

SOURCE: how to remove and repalce vw golf wing mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can remove the bolts securing the mirror to the door.

Posted on Sep 18, 2009

  • 811 Answers

SOURCE: how to remove 1999 vw jetta glove box door

lubricate lock with silicone spray lubricant, see if there are screws under door

Posted on Oct 09, 2009

  • 1 Answer

SOURCE: 2002 VW Golf Headreast Removal

Same proceedure as front headrests but tilt the back of the seats forward about halfway. Push the little clip in on top of the seat, by the chrome rail, pull the headrest up and slide out of the hole. Push the back of the seat back, lift up the bottom seat and tilt forward. Lay the back seats down. Done.

Posted on Feb 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing the evaporator box


http://mechdb.com/index.php/Ford_Escort_evaporator_core_%26_blower_replacement
Ford Escort evaporator core & blower replacement
Removing the dashboard is not required in order to replace the evaporator core or the blower box.
Procedure
  1. Disconnect the A/C lines sticking out of the firewall beneath the hood. They are quick disconnect fittings and require a disconnection too that is fairly cheap and available at any auto parts store.
  2. Remove the 2 (7mm) screws holding the glove box in.
  3. Remove the glove box.
  4. Take out the 4 (7mm) screws in the plastic that is closest to the passengers door.
  5. Remove the 3 screws (10mm) that hold the metal brace in that was behind the plastic previous removed.
  6. Remove that metal bar going across the bottom of where the glove box used to be. That has 2 (10mm) screws holding it on.
  7. Remove the wire harnesses that are attached to the blower motor. Optional: remove passenger kick panel.
  8. Remove the 3 (10mm) nuts that are holding the blower box in place. 1 is in the middle of the passengers side firewall at the bottom of the box, the second is to the right of that one about a foot over and the 3rd is in the middle of the firewall right behind the cable that controls the outside/inside air.
  9. Now remove the vent that goes to the windshield.
  10. Look to the left of the box you are removing. Then yank out the evaporator until it comes out, it's strong enough to not worry about breaking anything during removal. Don't forget to unhook your a/c lines on the inside the engine bay prior to pulling the box out.
  11. Install the replacement core in reverse order.
Also see
  • Ford Escort & ZX2 section for the entire index of all Ford Escort and ZX2 related articles.

Aug 06, 2015 | 1991 Ford Escort

1 Answer

How to remove glove compartment door


You need to remove the Glove Box first. Open the Glove box, there are usually three screws at the front bottom of the box, and two at the top. Gently pull the whole box forward and turn/pivot the box to the left. There will be some plug-in wires you need to disconnect... don't worry they only connect a certain way. Your box should be free now. You'll need to remove the screws (usually four) on inside door plate to detach the door stops (those curved parts). On the bottom front of the box you should find the screws that attach the door, via the hinges, to the box. Assembly is just the reverse order. It's not a quick process... so take your time.

Mar 02, 2015 | 1999 Cadillac Seville STS

1 Answer

Wgolf.mk4.reg2000.removing upper part inlet manifold.


If you have a 2000 VW Golf 2.0 liter, the answer is yes. Just remove the top part of the intake manifold. A magnet and long handle allen key set will make the job easier for removing/ reinstalling the cap screws. Once manifold off, cover the intake holes with blue painters tape, to avoid dropping any thing down in them. Take care on plug wire removal. Change each plug one at a time. ***Tighten spark plugs with a torque wrench, spec 22 ft-lb in the Bentley manual. AEG, AVH, AZG eng codes***

Jul 08, 2014 | 2000 Volkswagen Golf

1 Answer

Replacement of HVAC cabin filter


1. Remove the glove box behind it you will see a long cover with 4 screws you only remove 2 of these.
2. Remove the 2 screws the top left and the bottom right.
3. Replace the cabin filter re install screws
4. Re install the glove box door Done.

Apr 06, 2012 | Mitsubishi Cars & Trucks

1 Answer

The catch on the glove box lid on a vw golf 2001 is broken how do i fix it?


You need to replace the whole glove box door. Pry the panel on the right side of the dash off, remove the t25 screw, remove the 3 t20 screws along the bottom of the glove box, and the t20 screws that you can see inside the glove box. This will loosen it enough to pull the whole glove box loose. Then you need to remove the damper by prying the little plastic pin out. Then remove the bracket it secures to that has a t20 screw in it. There are 2 plastic pins in the hinges that need to be popped out, once this is done, the door will come off. Reassembly is the reverse.
If the pins are difficult to reinstall, file the new glove box door hinge holes with a round file. I usually shoot a little oil into the damper too, just to make operation easier.

Feb 04, 2011 | 2001 Volkswagen Golf

1 Answer

How to replace glove box latch The glove box latch is broken off and I can't get it open. I can get a new latch but don't know how to install it----am afraid I will break something. Help!


Remove the glove box: unscrew 3 screws inside the box (in a row towards the top) and 2 on the outside (one on the bottom right side- open the car door to access it, and one on the bottom left side). Grab the bottom of the box and pull it toward you. It will come off.

Once it's off, flip it over. There are 2 screws that hold the latch housing on the box (you'll find them in the 2 circles that are cut into the plastic). Unscrew them.

Next, flip it back over to the front and stick a small flat screwdriver between the latch housing and the glove box part that it's stuck into. Gently pull the latch and the whole thing should come out.

Pop the new one in, replace the screws, put your glove box back in your car, and you're good to go!

Mar 27, 2010 | 1998 Volkswagen Golf

1 Answer

How to remove 1999 vw jetta glove box door


lubricate lock with silicone spray lubricant, see if there are screws under door

Oct 09, 2009 | 1999 Volkswagen Jetta

3 Answers

How to replace the cabin air filter in a 2000 toyota avalon xls


lower the glove box and its forward of that, should be a plastic panel to remove.

Sep 23, 2009 | 2004 Toyota Avalon

1 Answer

1999 olds cutlass glove box removal


you need to remove all the screws on the bottom of the glove box on the outside, then on the inside remove all the screws too. and then pull it out. sometimes some glove boxes have stoppers on the edge of the door inside and you have to pry on them to pull the stoppers in front of the side of the glove box so you can remove it entirely from the dash.

Jul 19, 2008 | 1999 Oldsmobile Cutlass

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...