Question about 1996 Chevrolet Blazer

Open Question

Intake manifold torque sequence on 2000 mercury sable

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ZX2Fast
  • 547 Answers

SOURCE: 02 Chevy avalanche 1500 need

1st pass 44 inch lbs
2nd pass 71 inch lbs, check the manifold joints for shifting and fix if needed
3rd pass 106 inch lbs
4th pass 11 ft-lbs

Start in the center and tighten in a criss-cross pattern.

Posted on Nov 27, 2010

Ad
  • 335 Answers

SOURCE: cylinder head bolt torque chevrolet 3.4

here is the troque spec for the cylinder heads.

Cylinder Head Bolt

  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees


Cylinder Head Bolt
  • First Pass
60 N·m
44 lb ft
  • Final Pass
95 degrees
first pass 44 ftlbs
second pass 95 degrees

Posted on Jun 19, 2010

ZJLimited
  • 17970 Answers

SOURCE: intake manifold torque specs and

8ef3de6.jpg

Fig. Exploded view of the upper and lower intake manifold and fasteners

- Position the rocker arms in their original locations and tighten to the proper specifications.

- Install lower the intake manifold attaching bolts. Apply sealant or equivalent thread locking compound to the threads of bolts. Tighten the vertical bolts first, then the diagonal bolts to 115 inch lbs. (13 Nm).

- Install the upper intake manifold and tighten the mounting bolts to 18 ft. lbs. (25 Nm).

Hope helps (remember to rate this).

Posted on Oct 05, 2010

jimmybrown67
  • 835 Answers

SOURCE: what is the torque specs for a 2000 chevy vortec

tighten in 3 steps 1) 26in-lbs 2)106in-lbs 3)132in-lbs

Posted on Nov 02, 2010

ZJLimited
  • 17970 Answers

SOURCE: What is the torque specifications and sequencing

zjlimited_198.jpg

Fig. 1: Intake manifold installation-4.3L engines (click over image for zoom)


zjlimited_200.jpg

Fig. 2: Intake manifold bolt tightening sequence-1996-98 4.3L engines

Install the bolts and tighten in sequence and in 3 steps as follows:

  1. First step to 26 inch lbs. (3 Nm).
  2. Second step to 106 inch lbs. (12 Nm).
  3. Final step to 11 ft. lbs. (15 Nm).

Hope this helps (remember to rate this answer). Good luck.

Posted on Dec 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The proper way to install intake manifold


You should use a light duty Torque wrench and use a sequence that usually starts in a middle bolt location and alternates side to side and works from middle holes to extreme ends. I have not tried a Web search but you could try a search that would say something like "1996 Mercury 4.6L intake manifold tightening sequence"

Sep 19, 2015 | 1996 Mercury Grand Marquis

1 Answer

2000 chevy v-6 4.3 torque sequence and settings for intake manifold


lower intake manifold

step 1 27 inch lbs.

step 2 106 inch lbs.

step 3 134 inch lbs.



johnjnail_54.jpg
upper intake manifold

step 1 44 inch lbs.

step 2 80 inch lbs.

Jun 01, 2011 | 2000 Chevrolet Blazer

2 Answers

I need lower manifold rocker and upper manifold torque instructions please help


Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

Dec 05, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Need the torque specs for the upper intake bults on a 2002 chrysler sebring conv. 2.7L


4022caa.jpg

Fig. Intake manifold bolt torque sequence 2.7L engine

Upper intake manifold with a new gasket on the lower intake manifold and torque the bolts, in sequence, to: 105 inch lbs. (12 Nm)

Hope helps (remember to rate this answer). Good job.

Oct 11, 2010 | 2002 Chrysler Sebring

1 Answer

Need to replace intake manifold how do you do this


Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

3.8L Engine
VIN 1 Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
To install:
  1. Install or connect the following:
    Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

VIN K Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

    a5adffa.jpg
    Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
To install:


140d431.jpg
Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


4950e4f.jpg
Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
  1. Install or connect the following:
    Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
  2. Refill and bleed the cooling system.
  3. Run the engine and check for leaks and proper engine operation.

Hope this help (remember rated this).

May 17, 2010 | 2001 Pontiac Bonneville

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold


Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

May 07, 2010 | 2001 Jeep Cherokee

1 Answer

Where is the thermostat located on my 2000 sable


it is in the housing from the top rad hose to the intake manifold,remove the top hose,after draining the coolant,and the thermostat will be under the the peice it fastens to on the engine.

Jul 30, 2009 | 2000 Mercury Sable

2 Answers

2000 Mercury Sable 24V 3.o engine. Need to know


yes about the upper intake and the only way i know how to check the coils is with a engine anilyser or if the check engine light comes on then you can have the codes pulled and that will tell you which cylender is missfiring this engine has a indevidual coil for each spark plug so thares 6 of them and thay slide right down over the sparkplugs

May 05, 2009 | 2000 Mercury Sable

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...