2005 accord hybrid blinker door mirror

fuse diagram for Ford escape

https://ricksfreeautorepairadvice.com/2006-ford-escape-fuse-diagrams/

Instructions1.

• 1

Remove thedoor panel. Refer to your Honda Accord repair manual for theinstructions in removing the door panel. Unhook the rods and connectors on theinside of the door panel and set it on the floor.

• 2

Remove thefilm covering the access to the side mirror. It's difficult to avoid damaging thefilm while removing it so you will need to purchase a new piece of filmcovering when you buy a new side view mirror.

• 3

Reachthrough the service hole into the mirror housing with a screwdriver. Loosen thescrew that holds the mirror. Twist the screw out with your hand.

• 4

Reacharound the door and support the mirror with your other hand. Continue to twistthe screw out, then catch the mirror as it drops out when you remove the screwcompletely. Put the screw in a safe place so you don't lose it.

• 5

Installthe new side view mirror by positioning it where the old mirror was. Insert thescrew you took out in Step 4 and twist it in with your hand. Insert ascrewdriver into the service hole to tighten the screw.

• 6

Replacethe film covering that was damaged when you took out the old mirror. Push itinto place in the indentation on the door.

• 7

Sit in thecar seat and adjust the mirror so you can use it properly.

Hello,

To replace the mirror of your car all you have to do is follow the process below,

1. Remove the plastic shards of mirror lens from the mirror shell,
2. If any of the shards are still stuck to the mirror, pull them off the motor and discard them,
3. Sweep any small shards out of the shell with a vacuum cleaner,
4. Place the new mirror lens into the mirror shell, the lens has a small metal bracket on the back of it that fits over the motor.
5. The tight fit of the mirror in the shell forces the bracket to line up with the motor.
6. Push the mirror bracket onto the motor by pushing on the center of the mirror lens with your hand. You will feel the bracket snap into place.

But if you want to remove the entire mirror, then you will have to follow the steps below for the DIY process:

1. To replace the outside mirror, the door panel needs be taken off to get to the retaining nuts and the wiring.
2. You will need a few common tools, Phillips screwdriver, flat head screwdriver, and a 10mm socket and ratchet. No special tools are required.
3. Remove the Phillips screws located in the arm rest.
4. Remove the screw in the door handle.
5. Remove any screws that may be located around the circumference of the door panel.
6. Use the common screwdriver and insert it in between the door panel and the door and pry out the trim fasteners around the circumference of the door panel.
7. These trim fasteners are plastic plugs with serrated edges on the shank and pushed into holes on the door. Once these are removed, lift the bottom of the door panel straight up to unlatch the panel from the top horizontal ledge.
8. If the vehicle happens to be a Ford, it uses downward facing hooks on the door panel that hook into the door. Simply lift straight up to remove the hooks.
9. Bring the door panel just far enough to remove the door handle rods if necessary.
10. Disconnect the power window electrical connectors. Remove the lower door panel's marker light connector.
11. Disconnect the power outside-mirror electrical connector and then using the 10mm socket, remove the three retaining nuts on the backside of the outside mirror.
12. Withdraw the mirror and studs from the door.
13. Install the electrical connector for the new mirror through the opening in the door and line up the studs on the mirror with the holes in the door and push it through.
14. Install the nuts on the backside. Connect the electrical connector.
15. Hold the door panel close to the door and connect all the electrical connectors.
16. Tip the bottom of the door panel outward slightly to attach the top curved surface to the horizontal channel.
    
17. Lower the bottom of the door panel and line up the trim fasteners with the holes in the door. Once lined up, push them into the holes to hook the door panel.
    
18. Replace all the screws in reverse order of removal.

Take care.

1. check to see if there is a fuse for the mirrors and replace if bad.
2. check mirror control switch to make sure its working, also check contacts and make sure there clean, u can use a volt meter to see if there is power going to and from the switch, but if both mirrors are not working the rule of thumb is it must be something that would effect both and not just one mirror such as bad fuse bad switch or a break in the power line goting to the switch.

hope this helps

you have to remove the door panel and upholestry as well as the side shield blocking the bolts to the mirror.

1.)remove door upholestry by unscrewing the screws,

• under a hide cap by the door handle,
• under the door opening lever
• and some other places Look closely
• remove the clips by prying the panel back.
• remove electrical jacks connecting to the switches of the door
  

2.)remove the side shield blocking the bolts to the mirror

install new mirror.

1) Disconnect the Corolla's negative cable to the battery.

2) Remove the triangle-shaped interior mirror cover from the top of the
door panel. Pry the cover off with your hands, a blunt plastic or
wooden tool to prevent damage to your door trim.

3) Take out the mirror wiring connection.

4) Remove the door trim bracket around the mirror. Take out the
mounting nuts.

5) Pull the power mirror off the Toyota Corolla.

1) Put the new mirror in place on the Camry.

2) Re-install the mounting nuts making sure they are securley holding
the mirror in place. Replace the mirror insulation.
3) Reconnect the wiring to the new mirror.

4) Install the triangle interior cover by snapping it back in place.

5) Connect the negative battery cable.


Thanks
Xeeshan

your new mirrors should come with the instructions shor installing and wiring them up, if ordered for your car.

2005 Freestyle/Five Hundred/Montego Workshop Manual

1. Remove the exterior mirror trim cover.(on inside of door)
   

1. Disconnect the exterior mirror electrical connector.

1. Remove the 3 exterior mirror nuts.

1. Remove the exterior mirror.

1. To install, reverse the removal procedure.

For a 2005 Honda Pilot, I am a complete Amateur and I had no problem installing this mirror.

1) Lower the window, and only remove the Interior MIRROR panel, NOT the entire DOOR Panel, as some sites my recommend.
2) Once the Interior Panel is removed, the power cable is attached to the mirror, remove this cable.
3) There are 3 Bolts that are BLACK (atleast in my vehicle) that need to be removed.
3) Once the bolts are removed, the mirror should come off easily.
4) Place the new mirror in place of the old one and secure all three bolts, and then secure the power cable.
5) Then place the interior panel back.

That is it!

try a glass place or take back to dealer to get the correct adhesive for the indicator