Question about 2005 Chevrolet Silverado

Open Question

1988 chevy siverado instrument cluster wire diagram

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: have a 1988 chevy 1500,

Make sure your dimmer switch is turned all the way up to high. If it is not working your instrument cluster lights then replace your dimmer switch first. If your dimmer switch is good then the next thing to do is remove the instrument cluster from your dash and replace the mini lightbulbs. One of them has burned out and when one goes out, they all go out. You can get replacement bulbs at your local auto parts store for a few bucks each.

Posted on Sep 14, 2010

  • 2 Answers

SOURCE: Engine Wire diagram for S10

go to autozone.com and you can register any type car and they have pretty good prints and service manuals on line. I have an 89 chevy s10 I just rebuilt my motor and overhauled the complete truck just waiting on a new paint job. best of luck

Posted on Nov 28, 2008

Michael2010
  • 14 Answers

SOURCE: I have a chevy 1500 silverado and the instrument cluster stopped

Hello Ron Sadora, Your cluster is totally digital.. Mike www.kincerservice.com

Posted on Jan 27, 2010

  • 1 Answer

SOURCE: trying to convert a 1990 Chevy k1500 instrument

did you get an answer to this question?
Basically you need the DRAC out of the donor vehicle. It is located behind the glove box. 3"x3" square box. Depending on axle gear ratios and tire size you may need to change the jumper settings to allow your speedometer to read properly. This is a very simple procedure.
To convert any 88 and later to the 94 dash you will need not only the drac but get it's harness with at least 6" of its wiring as well.
You will need the 94 dash plug also with at least 6" of wiring on it too.

Posted on Feb 16, 2010

  • 10 Answers

SOURCE: Instrument cluster not working

if its not a fuse. try a relay. itll be under the hood in a little box. if thats not it than it could be a short in the wiring.check your running lights as well. most of the time they are ran on the same fuse so if one doesnt work the other one probably wont. also if you have recently replaced your stereo. check over the wiring on it because something could have got loose.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2004 chevy tahoe. Once the instrument cluster wire clip is detached and new bulbs are soldered on the cluster. Does the instrument cluster have to be reprogrammed ?


Shouldn't need reprogramming. I removed the cluster from my 04 Silverado and sent it in for repair and replacement of the bulbs. It was out of my truck for 2 weeks. When I got it back everything worked just fine, no problems at all.

Jan 15, 2017 | 2004 Chevrolet Tahoe

2 Answers

All gauges quit working. Replaced all stepper motors. Still nothing is working.


Is there power (B+) an ground's for instrument cluster ? When you turn the key to the run position ( not start ) do the gauges do the sweep test ?
Did you perform the Instrument Cluster Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Instrument Cluster
2
Turn the ignition ON, with the engine OFF.
Observe the instrument cluster.
Does the instrument cluster perform the displays test?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

Turn the ignition OFF.
Disconnect the IPC.
Turn the ignition ON, with the engine OFF.
Connect a test lamp between the ignition 1 voltage circuit and a good ground.
Does the test lamp illuminate?

Perform Diagnostic System Check - Instrument Cluster , Diagnostic System Check - Driver Information Systems or Diagnostic System Check - Audible Warnings before using the Symptom Tables in order to verify that all of the following are true:
• There are no DTCs set.
• The control modules can communicate via the serial data link.
Review the system operation in order to familiarize yourself with the system functions. Refer to the following:
• Instrument Cluster Description and Operation
• Indicator/Warning Message Description and Operation
• Driver Information Center (DIC) Description and Operation
• Audible Warnings Description and Operation
If you don't know about serial data communication an DTC'S I strongly suggest you take your vehicle to a Chevy dealer or an ASE certified repair shop .

Mar 04, 2016 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

I have a 1988 Alfa spider with a non working instrument cluster. Is it true that only the exact same year and month produced cluster will work in an 88?


First why is your cluster dead? If it's one of the circuits, it can probably be fixed. Since you live in CO there are plenty of places around Boulder and Ft Collins who can repair circuits.

So so without knowing more I'd need to trouble shoot why the entire cluster is dead.

Yes harnesses can can be modified. If your car has the mouse type belts you're going to need to trace the circuit that powers the mouse. All things being equal, the '87 and '89 wiring should be similar except for the mouse part. You'll need wiring diagrams for your car and the donor cluster. You can get copies at Alfa BB. You'll need your connectors off your old cluster.

Again in these are electronic circuits and can likely be modified by computer repair or electronic circuit repair shops.

Good luck. Personally I hate the automatic belts.

Feb 20, 2015 | 1988 Alfa Romeo Spider

1 Answer

Where are the two flashers located on 1988 chevy s10 extended cab pickup


One should be on the fuse box under the instrument cluster, and the other is in the wiring harness behind the radio.

Feb 18, 2015 | Cars & Trucks

1 Answer

Repair siverado cluster


Don't know what your question is but you can't fix an instrument cluster yourself. They have to be taken out and sent to a service center.

May 16, 2011 | 2003 Chevrolet Silverado 2500HD

1 Answer

Removal of truck radio


There are two, if it's 1/4 inch round it goes to the antena if it's a single black wire connected by itself in the middle radio it's the ground and connects to the chassis. All other wires run into the connecter and feed speakers and has the power to it.

Jul 04, 2010 | 1988 Chevrolet K1500

1 Answer

1992 ford escort wiring diagrams


I have the instrument cluster diagrams, need an email address to send to in pdf format

Feb 10, 2010 | 1992 Ford Escort 4 Door

Not finding what you are looking for?
2005 Chevrolet Silverado Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...