Question about 1998 Chevrolet Blazer

Open Question

Front turn signal on a 2004 chevy blazer - 1998 Chevrolet Blazer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

Ad
  • 324 Answers

SOURCE: how replace turn signal switch 2000 chevy blazer?

Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Posted on Oct 07, 2009

  • 3741 Answers

SOURCE: Where is the turn signal relay on a chevy s10

On 95-97 and 1998, both the turn signal and hazard flashers are located behind the lower dashboard trim just to the left of the cigarette lighter. You can not get to it without taking apart the trim (stupid design). Or you have to drill a 2" diameter hole in the trim with a velcro cover so you would never have to do it again1999 and later it is under the glove compartment
to disassemble it without drilling
It's behind the panel to the left of the cigarrette lighter. You need a Torx 25 screwdriver and another screwdriver for those hex shaped screws, forgot the size. First unscrew the 2 Torx 25 screws beneath the steering wheel. Then unscrew the rest of those Hex screws on the bottom. The panels overlap, so be prepared for a lot of unscrewing. You do need to unscrew the middle black panel on the bottom, right beneath the cig lighter. It's held by two Hex shaped screws, one on each side and are hard to unscrew. Also you need to remove your spare change sliding tray to unscrew the last hex looking screw. Once you pop your panel off, the turn signal flasher is the right one. The Hazard flasher is the left one. You can find a replacement part at Autozone, and DON'T get the $184 Flasher switch, all you need is the signal flasher. It's shaped like a cylinder with TWO prongs on it.

Posted on Nov 03, 2009

alicantecoli
  • 22246 Answers

SOURCE: 2004 Chevy Malibu turn signal issues

check the bulb with a test meter and alsof or a feed

Posted on Nov 25, 2009

  • 1 Answer

SOURCE: 91 Chevy K5 Blazer turn signal flasher

i agree with them, but you know when you open the door and thatgod damn buzzer goes off until you turn on the truck? how the hell do you shut that off?
please email me Steveracer8@hotmail.com
thanks

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 chevy blazer clunks only in 4whl drive, right front. Anyone know what it might be?


There is so much turning up there that it can be several things. The normal Balljoint problem can have the part slip in and out of its socket if it gets loose. Check your tierod ends for slack.
Sometimes Calipers can rock if they are failing to float properly with loose hardware. The front torque is changing from being pushed by the rear wheels to pulling with the front wheels.
This can affect how the Balljoints react as the sockets are getting torque differently than in 2WD. You are also using the CV joints to pull rather than coasting in 2WD. Check your end play for the front hubs; they used to be about .005 and you need Year model specific Specs to be sure.

Check out some 4-Wheeling Blog sites as they may know more about the common problems. There are so many things to check that a Blog may be your best source.

Dec 08, 2011 | 2004 Chevrolet Blazer

1 Answer

Can you take the left front signal cover off on a 1997 chevy blazer to change the signal bulb


No. Unfortunately you have to remove the whole headlight assembly. There are two long screws holding it in. You access them from under the hood. Once they are removed you will be able to get the headlight assembly out and be able to get to the turn signal bulb.

Dec 10, 2010 | 1997 Chevrolet Blazer

1 Answer

I have a 1997 chevy blazer the hazards work fine but the turn signal is not working I checked the fuse in the fuse panel. what else could it be


Replace the Turn Signal Flasher Relay. It has 2 relays. One for the Hazard lights and one for the Turn Signals. The Turn Signal Flasher Relay is located Front seating area, driver side, passenger side of steering column, under dash, mounted near cigarette lighter. Optional mounting location is under dash, on driver side of steering column. (Curtorsey Auto Zone)

Dec 15, 2009 | 1997 Chevrolet Blazer

3 Answers

How replace turn signal switch 2000 chevy blazer?


Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Oct 07, 2009 | 2000 Chevrolet Blazer

1 Answer

I have a 2000 Chevy Blazer. My turn signals click


Does it do it on both sides?If it is just on one side,a bulb could be the problem.When it does this,check the bulbs,by turning the signal on,and look at the front ,and the back,to see if one bulb is not burning.Replace it .One other problem ,check to see if the turn signal fuse is not blown,but melted in the fuse block.The battery voltage needs to be checked also.Check the charging system.it should be at about13.58 to 14.25.If the charging system is not at least 13.50 at idle,chatge battery at slow charge at 2 amps for 24 hours.If the voltage does not come up above 13.501 at idle,have the alternator replaced.The flashers,and the turn signals require a lot of amps.

Aug 29, 2009 | 1995 Chevrolet Caprice Classic

1 Answer

I have a 98 Chevy Blazer, the left front turn signal blinks really fast. What should i do?


This usually means that you have a bulb burnt out. Check the left rear

Mar 03, 2009 | 1998 Chevrolet Blazer

1 Answer

How do you replace a front turn signal on a 2002 Chevy Blazer


open your hood between the battery and the front core support is 2 black plastic clips pull them up and set aside then your head light fixture will come out for you to change your lights

Feb 10, 2009 | 2002 Chevrolet Blazer

2 Answers

Replace the front turn signal light bulb


you have to go under the front of the car. very easy to fix.

Oct 21, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...