Question about 1994 Chevrolet Suburban

Open Question

Where is the ecm fuse located on a 1994 chevy suburban

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
1beertap
  • 32 Answers

SOURCE: PCM module, ECM module 1996 Chevy Suburban K model

Powertrain Control Module = under right side of dash, near blower motor.
Engine Control Module = same as above
Vehicle Control Module = same as above

All Suburban vehicles are equipped with only one of these choices. Good luck.

Posted on Oct 04, 2008

Ad
psds4
  • 293 Answers

SOURCE: no turn signals or side brake lights on 94 chevy suburban

the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Posted on Oct 18, 2008

  • 64 Answers

SOURCE: trying to find the fuse diagram for my 1992 chevy astro van

It should be marked on the fuse block

Posted on Mar 29, 2009

  • 1 Answer

SOURCE: Electronic Control Module Installation 1994 G20 Chevy Van

I just had the same problem. If it is a regular van try under the driver seat in a plastic box. If it is a conversion van try in a pannel just behind driver seat on side of van wall behind a pannel that looks like a vent.

Posted on Apr 09, 2009

BCAS1298
  • 3092 Answers

SOURCE: Underhood fuse panel on a 1994 Chevrolet Suburban K2500

Under the hood driver side close to the master cylinder and fender, has black cover , pull cover off.Hope this was helpful.

Posted on Dec 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I reset fuel shut off on 2002 Chevy suburban


their is no reset / inertia switch on suburban only fuses and relays ---will need to test fuses relays wiring connections and or pump for where failure is

Dec 16, 2016 | 2002 Chevrolet Suburban

1 Answer

Does an 87 chevy suburban have a chip (not an ecm) for the tbi? And if so where is it located?


Chevy Suburban replacement key ? Mile High Locksmith ™

www.denver-locksmith.net/2013/.../replacement-key-for-chevy-suburba...
If you have lost your key to your Chevy Suburban, and have no spare, the cost of ... 1976, 1977, 1978, 1979, 1980, 1981, 1982, 1983, 1984, 1985, 1986, 1987, 1988, ... and 2013 then your Chevy Suburban will require a transponder chip key.

Chip it! Finale- - YouTube

? 3:41
https://www.youtube.com/watch?v=CSFR7XldItE
May 23, 2010 - Uploaded by pearsonba350
Final installment of my Jet Performance chip install on my '94Chevy truck. ... Just throwing it out there i ...

Nov 19, 2015 | Cars & Trucks

1 Answer

1994 Chevy Suburban the fuel gauge stays on empty and the low gas indicator does not come on.


A common problem with older Chevy trucks is the fuel level sending unit. This is located in the fuel tank and is very likely your problem.

Jul 08, 2012 | 1994 Chevrolet Suburban

1 Answer

No s.e.s.lamp no spout voltage to tps map all fuses and fuseable links good .Won't camunicate with scan tool 1994 chevy sub 5.7 tbi 2wd auto trans .Also fuel pump does not come on ,can jumper fuel ,pump ok...


Remove the radio and make sure he did not cut any wires to the ECM engine control (module).The wires run along the back of the radio to behind the glove box to the ECM.If this is all good then check the connections.If all is good then you could have a bad ECM.Tyr the scan tool on another vehicle to make sure the scan tool is working properly.Hope this helps.Good luck.

Mar 24, 2010 | 1994 Chevrolet C1500

1 Answer

1994 chevy suburban silverado horn does not work and dash lights are not working


there is a 20 amp fuse in the fuse block that feed these circuits

Mar 05, 2010 | 1994 Chevrolet Suburban

1 Answer

Underhood fuse panel on a 1994 Chevrolet Suburban K2500


Under the hood driver side close to the master cylinder and fender, has black cover , pull cover off.Hope this was helpful.

Dec 15, 2009 | 1994 Chevrolet Suburban

3 Answers

PCM module, ECM module 1996 Chevy Suburban K model


Powertrain Control Module = under right side of dash, near blower motor.
Engine Control Module = same as above
Vehicle Control Module = same as above

All Suburban vehicles are equipped with only one of these choices. Good luck.

Oct 04, 2008 | 1996 Chevrolet Suburban

Not finding what you are looking for?
1994 Chevrolet Suburban Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...