Question about 1991 Chrysler LeBaron

1 Answer

Replace crankshaft oil seal - 1991 Chrysler LeBaron

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,101 Answers

You will need a chrysler harmonic balancer pulley to get the harmonic balancer off

Posted on Oct 29, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a nissan 1400 champ and is leaking oil on the front part of the manual 5 speed gearbox and the rear part of the gearbox. I have replaced the crankshaft oil seal but i still have oil leaking on


There are seals on the front and rear of the transmission. If the clutch wasn't covered in engine oil, then replacing the crankshaft seal wasn't necessary. Reseal the transmission.

Sep 29, 2014 | Nissan Cars & Trucks

1 Answer

How to replace front crankshaft seal


replace Front main oil seal mighty max 1988 can i get a digram

Aug 24, 2012 | Mitsubishi Mighty Max Cars & Trucks

1 Answer

How do I replace the rear seal on a cadillac cts


YOU NEED TO REMOVE FLYWHEEL REMOVE OIL PAN. REMOVE REAR OIL SEAL HOUSING BOLTS. USING THE PRY POINT LOCATED AT THE EDGE OF THE CRANKSHAFT REAR MAIN SEAL HOUSING SHEAR THE RTV SEALANT. REMOVE THE REAR MAIN OIL SEAL. INSTALL GUIDE PINS INTO THE TWO CRANK SHAFT REAR OIL SEAL HOUSING CORNER BOLT HOLES OF THE ENGINE BLOCK.INSTALL THE CRANKSHAFT REAR SEAL INSTALLING TOOL ONTO THE REAR OF THE CRANKSHAFT FLANGE. APPLY A 0.2 INCH 3MM BEAD OF SILICONE SEALANT TO THE REAR OIL SEAL HOUSING . INSTALL THE REAR HOUSING TO THE ENGINE BLOCK.REMOVE THE GUIDE PINS AND INSTALL THE HOUSING BOLTS TIGHTEN THE BOLTS TO 89 INCH LBS. REMOVE THE REAR SEAL INSTALLATION TOOL FROM THE CRANKSHAFT FLANGE.THEN INSTALL OIL PAN AND FLYWHEEL.

Sep 10, 2011 | 2008 Cadillac Cts

1 Answer

I was told I have to replace the crankshaft seal and oil pan gasket on my 2000 chevy malibu and will cost approx. $380.00. Also is the rear main seal the same thing as the crankshaft seal??? Thanks!


Well sometimes.... the front crankshaft seal is usually called a crank seal, or the front timing cover seal but the rear crank seal is (usually) called the Rear Main crank seal. In order to replace the rear seal , the transmission will need to be removed. If its the front, then the harmonic balancer will be removed. $380 sounds cheap. As you will need a oil seal, oil pan gasket, oil, filter, labor and tax. Maybe even a lower engine mount.

Feb 01, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

How to repair front crankshaft seal leaks oil


Need to get at the crankshaft seal, usually by removing the crankshaft pulley and using a seal remover to take out the old seal, then put a new seal in.

Here are some instructions on how to do the 'rear' seal:
Rear Main Seal Removal & Installation 2.4L, 3.3L & 3.8L Engines To Remove:
  1. Remove the transaxle and flexplate. CAUTION
    Make sure not to damage the crankshaft sealing surface when removing the oil seal.
  2. Insert a flat-bladed pry tool or equivalent through the dust lip at an angle.
  3. Carefully pry the oil seal out of the engine. Pry against the chamfered edge of the crankshaft, do not damage the sealing surface of the crankshaft or an oil leak may occur.
To Install:
CAUTION
Smooth any burr or rough edge on the crankshaft with 400 grit sandpaper to prevent seal damage during installation.
NOTE: When installing seal, no lube on seal is needed.
  1. Place special tool 6926-1 seal guide or equivalent on crankshaft.
  2. Place the seal on the guide. Make sure the seal lip is facing the crankshaft and the guide tool remains on the crankshaft. Rear crankshaft seal installation (2.4L engine shown, 3.3L & 3.8L engines similar) chry-03-24-827.gif

    CAUTION
    Do not drive the seal into the block past flush. An oil leak may occur.
  3. Drive the seal into the block using a seal driver or special tool 6926-2 and handle C-4171 until the tool bottoms out against the block and the seal is flush.
  4. Install the flexplate and transaxle.
3.0L Engine To Remove:
  1. Remove the transaxle and flexplate. CAUTION
    Make sure not to damage the crankshaft sealing surface when removing the oil seal.
  2. Remove the oil seal with housing from the rear of the engine block.
  3. Remove the oil seal from the housing.
To Install:
  1. Clean the sealing surfaces on the seal housing and engine block.
  2. Use a commercial seal installer to install the seal in the seal housing.
  3. Apply a light film of motor oil to the seal lip.
  4. Apply silicone sealant to the oil seal housing sealing surface and install the housing with seal on the engine block. Tighten all bolts to 104 in. lbs. (12 Nm).
  5. Install the flexplate and transmission.
prev.gif next.gif

Dec 31, 2010 | 1997 Plymouth Voyager

2 Answers

How hard is it change front and rear oil seals?


By front and rear oil seals, I am assuming that you are refering to the CRANKSHAFT front and rear oil seals.
The front crankshaft oil seal is under all the components that must be removed to replace the timing belt.
The standard labor time to replace this seal is 4.0 hours for the 4 cylinder and 4.8 hours for the V-6.

The rear crankshaft oil seal requires removal of the transaxle to replace it.
The standard labor time required to do this is 7.3 hours

This is not a job for a novice unless you want to purchace a service manual and spend a lot of time reading the instructions before jumping into it.

Dec 01, 2010 | 1995 Honda Accord

1 Answer

Rear barring an seal replaced


I'm not sure if this is the right part of your car but, are you talking about the rear seal on the engine for the crankshaft?

If so:

Rear Main Oil Seal REMOVAL & INSTALLATION Fig. 1: Rear main seal installation for the 2.3L and 2.5L engines 85553306.gif
Fig. 2: Removing the rear main seal 85553307.gif
Fig. 3: Installing the rear main seal on the 2.9L engines 85553308.gif
If the crankshaft rear oil seal replacement is the only operation being performed, it can be done in the vehicle as detailed in the following procedure. If the oil seal is being replaced in conjunction with a rear main bearing replacement, the engine must be removed from the vehicle and installed on a work stand.
  1. Remove the starter.
  2. Remove the transmission from the vehicle, following the procedures in Section 7.
  3. On a manual shift transmission, remove the pressure plate and cover assembly and the clutch disc following the procedure in Section 7.
  4. Remove the flywheel attaching bolts and remove the flywheel and engine rear cover plate.
  5. Use an awl to punch two holes in the crankshaft rear oil seal. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. Install a sheet metal screw in each hole. Use two large screwdrivers or small pry bars and pry against both screws at the same time to remove the crankshaft rear oil seal. It may be necessary to place small blocks of wood against the cylinder block to provide a fulcrum point for the pry bars. Use caution throughout this procedure to avoid scratching or otherwise damaging the crankshaft oil seal surface. To install:
  6. Clean the oil seal recess in the cylinder block and main bearing cap.
  7. Clean, inspect and polish the rear oil seal rubbing surface on the crankshaft. Coat a new oil seal and the crankshaft with a light film of engine oil. Start the seal in the recess with the seal lip facing forward and install it with a seal driver. Keep the tool, T82L-6701-A (4-cyl. engines) or T72C-6165 (6-cyl. engine) straight with the centerline of the crankshaft and install the seal until the tool contacts the cylinder block surface. Remove the tool and inspect the seal to be sure it was not damaged during installation.
  8. Install the engine rear cover plate. Position the flywheel on the crankshaft flange. Coat the threads of the flywheel attaching bolts with oil-resistant sealer and install the bolts. Tighten the bolts in sequence across from each other to the specifications listed in the torque chart in this section.
  9. On a manual shift transmission, install the clutch disc and the pressure plate assembly following the procedure in Section 7.
  10. Install the transmission, following the procedure in Section 7.
prev.gif next.gif

Oct 07, 2010 | 1994 Ford Explorer Limited

1 Answer

I have a 2006 Pontiac Grand Prix, it is supercharged 3800. I have about 115,000 miles on it and I change the oil every 3,000 miles, check fluids, regular preventative maintenance, etc. I noticed a small...


If it's oil, it's coming from the rear main seal.. I would go with this idea.

The seal doesn't cost much but the labor to get to it does.

To give you an idea what is involved the procedure is illustrated below from the service manual:

Removal & Installation 3.8L Engine To Remove:
  1. Drain the engine coolant.
  2. Drain the engine oil.
  3. Remove the oil pan.
  4. Remove the engine flywheel.
  5. Remove the rear oil seal housing and gasket. Rear seal removal 3.8L gm-03-38-1175.gif

  6. Remove the rear main seal by placing the housing face down on 2 blocks of wood. Using a drift tool and hammer tap the seal out of the housing.
To Install:
NOTE: Do not lubricate the rear main oil seal or the installation tool. Do not touch the sealing lip of the rear main seal once the protective sleeve is removed.
NOTE: Use a clean lint free cloth to clean the crankshaft sealing surface. Remove sharp edges or burrs that could damage the rear main oil seal. Remove burrs or sharp edges with a crocus cloth.
  1. Carefully remove the rear oil seal from the protective sleeve.
  2. Install the oil seal onto the seal driver EN-47623 or equivalent by placing the seal at an angle and twisting until it is fully seated.
  3. Install the seal into the housing using the seal driver EN-47623 or equivalent and driver handle J-8092 or equivalent. Apply downward force until the seal is seated. NOTE: Ensure that the housing gasket is installed correctly and that the oil passages are not blocked.
  4. Using a new gasket Install the rear oil seal housing on the engine being careful not damage the rear main seal. NOTE: The plastic inserts are used in production and are not needed for assembly.
  5. Hand tighten the bolts. Rear seal housing alignment 3.8L gm-03-38-1176.gif

  6. Place a straight edge on the crankshaft rear oil seal housing flange and the engine block oil pan flange. Using a feeler gauge check that there is no more than .0004 in (0.10 mm) step on each side. Rotate the housing to make the steps equal on both sides.
  7. Tighten the housing bolts 11 ft-lb (15 Nm) plus an additional 50 degrees.
  8. Ensure that the housing did not move out of specification. Repeat step 6 if the oil seal housing is not within the specified range. Replace the rear oil seal housing if the specified measurement can not be reached.
  9. Install the flywheel.
  10. Install the oil pan.
  11. Fill the engine oil and the cooling system.
  12. Check for leaks
5.3L Engine To Remove:
  1. Remove the flywheel from the crankshaft.
  2. Remove and discard the crankshaft rear oil seal from the rear cover.
To Install:
  1. Use clean engine oil to lubricate the outside diameter of the crankshaft rear oil seal and rear cover oil seal bore.
  2. Install the tapered cone and bolts of a J 41479 or equivalent crankshaft rear oil seal installer onto the crankshaft.
  3. Place the crankshaft rear oil seal onto the tapered cone.
  4. Install the threaded rod of the J 41479 crankshaft rear oil seal installer into the tapered cone. Rear main seal installer 5.3L gm-03-53-3872.gif

  5. Install the crankshaft rear oil seal by turning the handle of the J 41479 clockwise.
  6. Remove the J 41479 crankshaft rear oil seal installer from the crankshaft.
  7. Install the flywheel onto the crankshaft.
prev.gif next.gif--- I'm not sure what the exact cost would be as the hours were not listed for this procedure on my online resource.

Sep 02, 2010 | 2006 Pontiac Grand Prix

1 Answer

I need but cant find a Chilton manual for my 1995 tercel. All I find are up to 1994. 1995 was the first year of the fifth generation Tercel so I doubt 94 would work. I need to find something so I can...


I only found a front crankshaft seal replacement not the whole crankshaft: Front Crankshaft Seal REMOVAL AND INSTALLATION 1.5L (5E-FE) Engine Tercel NOTE: The front oil seal can be removed from the engine without removing the oil pump.
  1. Disconnect the negative battery cable from the battery. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding.
  2. Remove the front covers and the timing belt.
  3. Remove the crankshaft timing belt sprocket. WARNING
    When removing the front seal, be extremely careful not to damage the crankshaft.
  4. Using a knife, cut off the oil seal lip.
  5. Tape the end of a flat bladed tool to avoid damaging crankshaft. Pry out the oil seal using the taped end of the tool.
  6. Inspect the oil seal riding surface on the crankshaft for signs of wear or damage. To install:
  7. Wipe the seal bore with a clean rag.
  8. Apply multipurpose grease the lip of a new oil seal.
  9. Drive the oil seal into place using tool SST 09309–37010 or an equivalent seal installer tool. Make sure the seal surface is flush with the oil pump case edge. Work from the front of the cover. Be extremely careful not to damage the seal.
  10. Install the sprocket without disturbing the Woodruff key.
  11. Install the timing belt and front covers.
  12. Connect the negative battery cable to the battery.
  13. Start the engine and check for leaks

Aug 01, 2010 | 1995 Toyota Tercel

1 Answer

1999 cross country v70 awd crankshaft seal replacement


Your info is confusing. The rear cam seal is not inside the timing belt cover, and the crank seal is at the bottom of the engine, while the cam seal is at the top.

Is there oil at the top, around the cam seal? Or just at the bottom? It's common for the oil pump seal to leak. If you get the oil pump reseal kit, it contains the oil pump seal and gasket, as well as the crankshaft seal. Make sure you seal the oil pump bolts, Volvo has special copper washers for this purpose.

Just try to locate the oil leak before replacing any more parts. Sometimes it can be something simple like the oil cap seal or the oil trap housing.


Bret
RepairPal.com

Nov 23, 2008 | 1999 Volvo V70

Not finding what you are looking for?
1991 Chrysler LeBaron Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...