Question about 1988 Mazda B2200

1 Answer

1988 mazda b2200 gets spark from the coil but not the distributor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 75,066 Answers

Remove the distributor cap, crank the engine is the distributor rotor turning? Then check the timing belt.

Posted on Oct 29, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: can a bad ignition switch cause the truck to die

Yes, bad ignition switch can cause that, did on my B2200.

Posted on Dec 14, 2009

  • 1 Answer

SOURCE: Fan blower doesn't work

I have the same truck. Mine only worked on high. I replaced the blower motor resistor and it worked for a few seconds and then the resistor started to overheat and fry. I then removed the blower motor and found it to be pretty seized up so I replaced it along with another resistor and it works great. At any rate, be careful not to ruin a new resistor. If it shows any signs of getting hot when you first fire it up then turn off the blower motor immediately and replace it too. In my case, the worn out blower motor is probably what caused the original resistor and the replacement to fail in the first place.

Posted on Jun 30, 2009

erietrack
  • 37 Answers

SOURCE: 93 mazda mx6 (v6) no spark.

Coil resistance is not a good way to determine if the coil is good or bad. It might still need replacing. Check to see if your getting a pulse signal to the coil. You can do this by hooking a milivolt test light to the trigger wire and ground. If it doesn't flash as you crank the motor, check out your pickup coil in the distributor. Some of them you can change. Some you have to replace the entire distributor. Sometimes oil will leak into the distributors on certain models which use an optical pickup. If this is the case, change the seal to fix the oil leak and GENTLY clean the optical sensor and photo wheel.

Posted on Nov 08, 2008

  • 5 Answers

SOURCE: I have 1987 Mazda B2200 2.2 ltre, turns, fires, no fuel psi.

I had something like this before. There is a fuel saftey switch near the gas tank right by the rear end. Its a roll over sensor and mine fell off the mount and I guess the truck thought it was upside down :)

Posted on Jan 01, 2009

jingB
  • 19 Answers

SOURCE: mazda engine bad

yes, i believe you could put any engine on your pick-up provided it is the rear wheel type set-up and the engine comes with its own tranny. problem is, if changing the engine mounts, tranny mounts, wiring set-up and exhaust system layout would not be of any problem to you. might as well look for the same mazda engine you have as a replacement to ease installation.

Posted on Apr 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 MAZDA B2200 DIES AND WONT START UNTIL IT SITS AWHILE HAS NO FIRE TO SPARK PLUGS WHEN THIS HAPPENS


I'd say the coil is shot. However when ot does happen make sure you still have 12volts going to the coil. This will help eliminate wiring issues.

Jul 12, 2014 | 1988 Mazda B2200

1 Answer

I have a 1987 mazda b2200 and have ggone through all the parts on distrubutor and coil and the truck has no spark coming from the coil .. c an anyone save me from taking it to a shop and costing me...


If you have 12 volts ( or 7.5volts) to one side of the coil and nothing on the lead to the distributor then I would think that the coil is burnt out or faulty. If you have the voltage through the coil to the distributor but cannot generate a spark out of the coil lead then it points to the module in the distributor being faulty. IF you have spark out of the coil lead but not out of the distributor cap to plugs then check the inside of the distributor cap for cracks and /or the rotor button not turning

Jul 01, 2014 | 1988 Mazda B2200

1 Answer

Wont start..no spark computer problem?


many things will cause no spark bad distributor cap or rotor.bad plug wires.ignition timing to far advanced cause by loose distributor.could have faulty ignition coil or module.check ignition fuse.probably could be faulty PCM i would have it checked out.could have bad crankshaft sensor.

Aug 01, 2013 | 1988 Mazda B2200

1 Answer

What is the gap setting on the spark plugs. please, 1991 mazda b2200


1992 MAZDA B2200 L4 - 2.2L - FI - - GAS

Part Number RN12YC - .035"

Hope this help (remember rated this) Good luck.

May 15, 2010 | 1988 Mazda B2200

1 Answer

When im driving my truck,it starts to sputter and


I would try spark plugs and wires. If it was a fuel line you would see the leak or atleast smell it very strongly. If the problem still exists after new plugs and wires try the distributor cap.

Apr 21, 2010 | 1988 Mazda B2200

2 Answers

Ignition wiring diagram Mazda B2000 1986


my 88 mazda b2200. none of the lights or fuel pump come on when i turn the key over, but i know the wires aint hooked up. im just trying to figure out where they are located

Mar 25, 2009 | 1988 Mazda B2200

1 Answer

Will not start, no spark


get spark tester and start testing from the spark plugs back. first hook it to aplug wire and check for spark if no spark ten hook it to the coil wire and check for spark if no spark then there is a chance that your coil or ignition module is bad if it is equipt with electronic ignition.

Aug 18, 2008 | 1988 Mazda B2200

1 Answer

Wont Start


Have another look at your plug wires, and make sure that you have them in the right order. As you probably know, if the firing order is wrong, you can have problems. That is somewhere for you to start, anyway.

Jun 18, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...