Question about 2009 Chevrolet Traverse
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Front lights
look at the head lights assembly. find some phillips screw there. two of them .either one on top and one on the side. these are the adjusting screws.
do it at night. park the car in front of a wall about 6 feet away and adjust the lights.
tnx 4 using fixya,
Posted on Nov 05, 2008
Posted on Oct 30, 2009
FACE THE VEHICLE SO THAT BATTERY IS ON YOUR RIGHT;
2.REMOVE THE BLACK PLASTIC PIECE THAT RUNS OVER RADIATOR BETWEEN HOOD LATCH AND FAN. IT IS ABOUT 53 1/2" LONG AND HOLDS THE HOOD PROP CLIP. (3 PLASTIC PUSH RETAINERS & 2 SHEET METAL SCREWS);
3.REMOVE THE GRILL ASSEMBLY UNDERNEATH THE PIECE IN STEP 2 BY PUSHING DOWN FIRMLY ON 4 RETAINER CLIPS WHICH RUN ALONG THE TOP. USE A WIDE SLOT SCREWDRIVER. PULL UP GENTLY ON GRILL ASSEMBLY. IT WILL POP OUT. THE GRILL ASSEMBLY EXTENDS UNDER EACH HEADLIGHT ASSEMBLY (HA) AND IT DISPLAYS THE CHEVROLET LOGO IN THE MIDDLE. MY GRILL ASSEMBLY POPPED OUT EASILY AND ALL THE OTHER RETAINER CLIPS ON THE BOTTOM AND BENEATH AND TO THE SIDE OF HA WERE AUTOMATICALLY RELEASED WITHOUT ANY FUSS;
4.ON TOP OF HA SEE ONE TAB (ABOUT 1" LONG)ON THE RIGHT SIDE AND ONE ON THE LEFT (THE ONE ON L IS CLOSER TO THE FENDER);
5.PULLUPWARDDIRECTION ON TABS. THEY WILL SLIDE UPWARD A COUPLE OF INCHES AND WILL RELEASE THE HA WHICH YOU CAN THEN PULL OUT TOWARDS YOU;
6.AT BACK OF THE HA, REMOVE 2 ROUND RUBBER CAPS (ABOUT 4" IN DIAMETER)--ONE FOR LOW BEAM--ONE FOR HIGH. REVEAL BULBS. UNSNAP THE WIRE HARNESS FROM BULB BASE AND TURN BULB 1/4 TURN CLOCKWISE (REMEMBER YOU ARE FACING THE TRUCK)
7.REPLACE BULB(S). #9006 BULB IS GRAY-BASE, FOR HIGH BEAM ON OUTSIDE. #9005 IS BLACK-BASE, LOW BEAM TO INSIDE OF HIGH BEAM.
CHANGING HIGH AND LOW AND REASSEMBLY TOOK ABOUT HALF HOUR. GOOD LUCK. ALTERNATIVE: IF YOU ARE REPLACING THE PASSENGERSIDE HEADLIGHT JUST REMOVE THE AIR FILTER COVER AND PULL PLUG OUR FROM BEHIND HEADLIGHT AND REPLACE. BE CAREFUL HANDLING LIGHT BULB. TO CHANGE THE ONE ON THE DRIVER'S SIDE JUST REACH IN FRONT OF THE BATTERY TO ACCESS THE PLUG AND HEADLILGHT. TOOK ABOUT 5 MINUTES. ENJOY YOU TRAILBLAZER, GREAT TRUCK.
Posted on Feb 21, 2010
Problems like these are more often the front wire harness that runs across the inside of you bumper and plugs in underneath the battery tray. A lot of shorts are found in these harnesses. Glad you got yours fixed.
Posted on Nov 05, 2010
SOURCE: I have a 1998 Chevrolet
THE HIGH BEAM LIGHTS WIRE COLOR LIGHT GREEN AND LOW BEAM WIRES TAN COLOR,YOU NEED LOOK IN A HAYNES REPAIR MANUAL IN THE ELECTRICAL SECTION AT HEAD LIGHT CIRCUITS.
Posted on Apr 07, 2011
Tips for a great answer:
Feb 06, 2015 | 2005 Chrysler Pacifica
Dec 21, 2014 | 2002 Chevrolet Cavalier Coupe
Nov 08, 2014 | 2007 Chrysler Sebring Sedan
Aug 20, 2014 | 2011 Chevrolet Traverse LS
Mar 28, 2013 | 1991 Nissan 300ZX
Nov 21, 2012 | 2009 Chevrolet Traverse
May 05, 2011 | 2010 Chevrolet Traverse
Apr 20, 2011 | 2001 Pontiac Sunfire
Nov 29, 2009 | 2007 Mercedes-Benz C230 Sedan
77 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: