Question about 1996 Ford Explorer

1 Answer

Timing chain cover

I took the cover off the timing chain, but now can''t remember where the brace goes.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

Have a look at this link & scroll down the page to see if what you need is there. Sometimes clicking on the picture will also expand it for you.

http://www.autozone.com/addVehicleId,2175001/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528018ec4f

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Click coming from timing chain x type 2.0 jaguar


if the noise is definately from the front engine timing chain cover area then the first thing i would do is remove the auxillary drive belt/fan belt then start the engine to see if noise is still there? if so the only option is to remove the front engine cover and from remember you may have to remove the cylinder heads also, even remove engine for access\,big job, the engine is normally a bullet proof unit, if the oil has been changed at service advised intervals then the hydraulic chain tensoiner etc should be ok and most noise problems at the front of engine area are caused by. ie. belt tensioner, air con compressor,pas pump etc. so if noise goes when aux belt removed look at the that area. hope this helps.

Jul 31, 2016 | Jaguar X-Type Cars & Trucks

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

Diragram on how to change the water pump on a 1995 z24 cavalier 2.3


Check this procedure, according with the repair guide for...

2.3L and 2.4L Engines
(see Figure 9)
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  1. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  2. Carefully lower the vehicle.
  3. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  4. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  5. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

zjlimited_2033.jpg

Fig. 9: Water pump and cover mounting - 2.3L and 2.4L engines (click over image for zoom)

To install:

  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Hope helps; remember to rating this answer and leave a testimonial comment. Thank you for using FixYa.

Oct 13, 2011 | 1995 Chevrolet Cavalier

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

1 Answer

What is timing cover and if this goes do you need to replace timing chain and water pump


engine with 3.3 liters and 3.8 liters are equiped with timing chain.
the timing chain cover is the cover that cover and protect the chain
it must be seal because there is oil that come from the oil pan to lubricate the chain.
normally the cover does not go bad unless the chain broke or some thing hits it.
the water pump is out side and not involed in the timing chain or it cover

Mar 05, 2010 | 1996 Plymouth Voyager

1 Answer

How do i change a water pump in a 97 grand am with a 2.4 litre engine


2.4L Engine
See Figure 3
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Disconnect the oxygen sensor wiring.
  4. Remove the upper exhaust manifold heat shield.
  5. Raise and safely support the front end of the vehicle securely on jackstands.
  6. Remove the exhaust manifold brace bolt.
  7. Unbolt and remove the lower exhaust manifold heat shield.
  8. Break loose the manifold-to-exhaust pipe spring loaded nuts.
  9. Unbolt the radiator outlet pipe assembly from the water pump cover.
  10. Disconnect the exhaust pipe from the manifold.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
Do not rotate the flex coupling more than 4°. this could damage the component.
  1. Separate the radiator outlet pipe from the oil pan and transaxle.
    1. On manual transaxle, remove the exhaust manifold brace.

  2. Next, leave the lower radiator hose attached and pull down on the outlet pipe to detach it from the water pump. Allow the outlet pipe to hang.
  3. Lower the vehicle.
  4. Remove the exhaust manifold-to-cylinder head nuts.
  5. Extract the manifold, seals and gaskets.
  6. Remove the timing chain cover. Refer to the procedure later on in this section.
  7. Remove the timing chain tensioner. Refer to Timing Chain removal later in this section.
  8. Unbolt the water pump from the cylinder block.
  9. Extract the pump assembly-to-timing chain housing nuts.
  10. Remove the water pump and cover assembly.
  11. Separate the pump from the cover.
  12. Clean all mating surfaces of gaskets and sealant materials.

To install:
Prior to installing the water pump, read the entire procedure. Pay special attention to the tightening sequence to avoid component damage and ensure a proper seal.
  1. Attach the water pump to the cover and hand-tighten the components.
  2. Lubricate the splines of the water pump drive with chassis grease or equivalent, then install the pump and cover assembly. Hand tighten the cover-to-block bolts.
  3. Install the pump-to-chain housing nuts and hand-tighten.
  4. Lubricate the O-ring on the radiator outlet pipe with an anti-freeze solution and slide the pipe into the water pump cover, install and hand-tighten the bolts.
  5. With the specified gaps, tighten in sequence as follows:
    1. Pump assembly-to-chain housing nuts
    2. Pump cover-to-pump assembly
    3. Cover-to-block, bottom bolt first
    4. Radiator outlet pipe assembly-to-cover

  6. Install the exhaust manifold using new gaskets.
  7. Install the manifold-to-cylinder head nuts, follow the tightening sequence and tighten to specifications.
  8. Raise and support the front of the vehicle.
  9. Index the exhaust manifold-to-exhaust pipe flange bolts.
    1. Turn bolt bolts in evenly to avoid cocking the exhaust pipe and binding the bolts. Turn the bolts in until they are fully seated.

  10. Install and secure the radiator outlet pipe to the transaxle and oil pan.

On manual transaxles, install the exhaust manifold brace.
  1. Install the timing chain tensioner and chain cover.
  2. Attach the lower heat shield.
  3. Lower the vehicle.
  4. Attach the exhaust manifold brace. Tighten the manifold-to-exhaust pipe nuts to specification.
  5. Attach and secure the upper heat shield.
  6. Connect the oxygen sensor wiring.
  7. Fill the radiator with coolant water mixture until it reaches the heater hose coolant outlet, then install the hose and continue to fill. This will assist with the complete cylinder block fill.
  8. Connect the negative battery cable.
  9. Start the engine and top off the cooling system and check for leaks.
ec6ae2e.jpg

Dec 28, 2009 | 1997 Pontiac Grand Am

1 Answer

WHERE THE WATER PUMP IS LOCATED on a 2.3 liter 4 cylinder quad hoc


it is driven off the timing chain, here is how you replace it
2.3L And 2.4L OHC Engines
  • Disconnect the oxygen sensor harness connector
  • Raise the vehicle and support it securely on jackstands
  • Remove the exhaust manifold brace and loosen the exhaust manifold bolts
  • Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine
  • Remove the exhaust manifold pipe from the exhaust manifold
  • Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging
  • Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head
  • Remove the timing chain cover from the engine
  • Remove the timing chain tensioner
  • Remove the water pump cover bolts from the engine block and the timing chain housing
  • Remove the water pump bolts and separate the assembly from the housing


Dec 01, 2009 | 1994 Pontiac Grand Am

1 Answer

IDLE PULLEY


Look like this?

56f293b.gif

Jul 24, 2009 | 1995 Nissan Altima

1 Answer

Oil pump replacement


This MAY seem Strange But It IS ALL necessary for Oil Pump Replacement. And Please Don't Forget to Rate Me as Most Folks Do Not. Thank You and GOOD LUCK with the Oil Pump Job Also


OIL PUMP
It is necessary to remove the oil pan, oil pickup and chain case cover to service the oil pump rotors. The oil pump pressure relief valve can be serviced by removing the oil pan and oil pickup tube. Refer to Timing Chain Cover Removal and Installation for procedures.

DISASSEMBLY
  1. To remove the relief valve, proceed as follows:
  2. Drill a 3.175 mm (1/8 inch) hole into the relief valve retainer cap and insert a self-threading sheet metal screw into cap.
  1. Clamp screw into a vise and while supporting chain case cover, remove cap by tapping chain case cover using a soft hammer. Discard retainer cap and remove spring and relief valve.
  2. Remove oil pump cover screws, and lift off cover.
  3. Remove pump rotors.
  1. Wash all parts in a suitable solvent and inspect carefully for damage or wear.
Oil Pump Assembly
  1. Assemble pump, using new parts as required. Install the inner rotor with chamfer facing the cast iron oil pump cover.
  2. Tighten cover screws to 12 Nm (105 inch lbs.).
  3. Prime oil pump before installation by filling rotor cavity with engine oil.
  4. Install chain case cover. Refer to Timing Chain Cover Installation.
REMOVAL of Timing cover
REMOVAL
  1. Disconnect negative cable from battery.
  2. Remove timing chain cover.
REMOVAL Of Oil Pan to gain Access to OIL PUMP
  1. Disconnect negative cable from battery and remove engine oil dipstick.
  2. Raise vehicle on hoist and drain engine oil.
  3. Remove bending brace to transaxle attaching bolt.
  4. Remove bolts attaching dust cover to transaxle housing. Lower dust cover to gain access to oil pan bolts.
  5. Remove oil pan screws and remove oil pan.
INSTALLATION
  1. Clean surfaces and apply a 1/8 inch bead of Mopar (R) Silicone Rubber Adhesive Sealant or equivalent, at the parting line of the chain case cover and the rear seal retainer.
    1. Use a new pan gasket.
    2. Install pan and tighten screws to 12 Nm (105 inch lbs.).
    3. Install dust shield and bending brace to transaxle housing.
    4. Lower vehicle and install oil dipstick.
    5. Connect negative cable to battery.
    6. Fill crankcase with oil to proper level.

Mar 27, 2009 | 1998 Chrysler Town & Country

Not finding what you are looking for?
1996 Ford Explorer Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...