Question about 2000 Chrysler Town & Country

1 Answer

I just changed fuel pump and filter in my 1999 chrysler town and country pump comes on for second then no power to pump

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 61 Answers

Make sure that the old pump is likely close to new one, or see the socket of your pump may be your new one is loosen to couple of your old pump. or try to loose or remove your new fuel filter then switch at the ignition, if the fuel is continues running the problem is your fuel filter, try another new filter.

Posted on Oct 29, 2012

  • bobbyjoemill
    bobbyjoemill Oct 29, 2012

    I unhooked both fuel lines from pump when the key is turned on the pump comes on for a second and cuts off it shuold stay on if no lines hooked up

  • Ronald Candia
    Ronald Candia Oct 29, 2012

    your new fuel pump wire line i think it loose try to fix it or your pump motor is defective

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

garyq1970
  • 73 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

  • 51 Answers

SOURCE: 1999 chrysler t&c needs a fuel pump

yes you need to drop the tank i worked for chrysler for a few years and i tried everything to try to slip the pump out with out fulling removing the tank and in the end its just easier to take the whole thing out.

Posted on Mar 15, 2009

reisdos
  • 1297 Answers

SOURCE: van will not start, I changed fuel pump and

can you confirm you have spark, fuel and injector pulse

additionally, what is the cranking speed of the engine?

Posted on Jun 04, 2010

  • 2 Answers

SOURCE: fuel filter on a 1999 chrysler town and country

I belive the filter is in the fuel tank, its an integeral part of the pump/pickup assembly

Posted on Aug 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the alarm system stop my 1999 town and country van from starting


Probably needs the fuel safety shutoff switch resset. I am not sure where it is on a Town and Country van.

Nov 29, 2014 | 1999 Chrysler Town & Country

1 Answer

Fuel filter on a 1999 chrysler town and country


I belive the filter is in the fuel tank, its an integeral part of the pump/pickup assembly

Aug 08, 2012 | 1999 Chrysler Town & Country

2 Answers

1999 chrysler town and country


Start with the simple fixes first; Try a new fuel filter. Then a new pcv valve. Both are very cheap & you can probably install them yourself.

Mar 31, 2009 | 1999 Chrysler Town & Country

1 Answer

1999 chrysler t&c needs a fuel pump


yes you need to drop the tank i worked for chrysler for a few years and i tried everything to try to slip the pump out with out fulling removing the tank and in the end its just easier to take the whole thing out.

Mar 15, 2009 | 1999 Chrysler Town & Country

1 Answer

Changing fuel filter on 2004 chrysler town and country


  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Aug 23, 2008 | 2004 Chrysler Town & Country

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...