Question about Cars & Trucks

1 Answer

What are the head torqes and do I need to replace bolts. Kia picante 1.1

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,671 Answers

Yes the bolts must be replaced.

Posted on Oct 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: what are the torque specs for the head bolts for a 1999 sportage

hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .

1999 kia sportage 2.0 DOHC head torque

Thanks for using FIX YA !

J5

Posted on Jan 24, 2009

michigan man
  • 3533 Answers

SOURCE: U' m repairing the head on 05 kia rio timing belt

try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 21, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

duane_wong
  • 6826 Answers

SOURCE: need head bolt torqe for 3100 and should bolts be

The bolts should have thread lock on them when installing, and the torque is done in 2 steps. 33 ft lbs. and then 90 deg. after that on the second pass. 3.1L Engine CAUTION
Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. LEFT SIDE (FRONT)

  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Disconnect the top half of the air cleaner assembly, then remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Disconnect the spark plug wires from spark plugs and looms then route the wires out of the way.
  7. Remove the rocker arm (valve) covers.
  8. Remove upper intake plenum and lower intake manifold.
  9. Remove the left side exhaust manifold.
  10. Remove oil level indicator tube. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  11. Remove rocker arms nut, rocker arms, balls and pushrods.
  12. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To install:
  13. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  14. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP are showing.
  15. Coat the bolt threads lightly with sealer, then install finger-tight.
  16. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  17. Install the pushrods, rocker arms, balls and rocker arm nuts in their proper locations. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  18. Install the lower intake manifold and upper intake plenum.
  19. Install the rocker arm (valve) covers.
  20. Install the oil level indicator tube. Insert the dipstick.
  21. Connect the spark plug wires to spark plugs and looms.
  22. Install the left side exhaust manifold.
  23. Install the exhaust crossover pipe and heat shield.
  24. Refill the cooling system.
  25. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  26. Connect negative battery cable.
  27. Start vehicle and verify that there are no leaks. Fig. 20: Cylinder head mounting and bolt tightening sequence - 3.1L engine 86883134.gif
RIGHT CYLINDER HEAD (REAR) CAUTION
Fuel Injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove the top half of the air cleaner assembly and remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Raise and safely support the vehicle.
  7. Detach the Oxygen (O2) sensor connector.
  8. Disconnect the exhaust pipe from the exhaust manifold.
  9. Remove the right side exhaust manifold.
  10. Carefully lower the vehicle.
  11. Disconnect the spark plug wires from spark plugs and wire looms and route the wires out of the way.
  12. Remove the rocker arm (valve) covers.
  13. Remove upper intake plenum and lower intake manifold. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  14. Remove rocker arms nut, rocker arms, balls and pushrods.
  15. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To Install:
  16. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  17. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP showing.
  18. Coat the bolt threads lightly with sealer, then install finger-tight.
  19. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  20. Install the pushrods loosely retained with the rocker arm assemblies. Make sure all pushrods are in the correct locations. Coat the ends of the pushrods with prelube. The intake rods are marked yellow and are 5 3?4 inch long. The exhaust pushrods are marked green and 6 inches long. balls and rocker arm nuts. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  21. Install the lower intake manifold and upper intake plenum.
  22. Install the rocker arm (valve) covers.
  23. Connect the spark plug wires to spark plugs and wire looms.
  24. Raise and safely support the vehicle.
  25. Install the exhaust manifold.
  26. Connect the exhaust pipe to the exhaust manifold.
  27. Carefully lower the vehicle.
  28. Connect the Oxygen (O2) sensor wiring.
  29. Install the exhaust crossover pipe and heat shield.
  30. Refill the cooling system.
  31. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  32. Connect negative battery cable.
  33. Start vehicle and verify that there are no leaks.
prev.gif next.gif

Posted on Feb 04, 2011

  • 1116 Answers

SOURCE: i need torqe specs for

Check out this link for your answers:

http://www.autozone.com/autozone/repairguides/Suzuki-Vitara-Grand-Vitara-XL7-2000-06/Specifications/Torque-Specifications/_/P-0996b43f8037c5e2

Posted on May 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I NEED TO KNOW THE TORQ SPECS FOR THE ENGINE, HEAD BOLTS ETC


get a Haynes manual for your vehicle costs about 40 dollars.

Oct 26, 2017 | Cars & Trucks

1 Answer

Head torq settings on a 2005 1.8 opel corsa utility


use new bolts
25NM
90 deg
90 deg
90 deg
45 deg

Apr 30, 2016 | 2005 Opel Corsa 1.8

1 Answer

Torq settings on 3.7 cyl heads


This is the info for the 2.8d CRDI 2008-11 engine code ENS (51C)

1 Replace Head Bolts
2 Stage 1 Tighten to15 Nm
3 Stage 2 Tighten to 30 Nm
4 Stage 3 Tighten to 85deg
5 Stage 4 Tighten to 85 deg
6 Stage 5 Tighten to 85 deg

Sequence

w93gwmwpatg0gaaaabjru5erkjggg==
If it is the 01-08 model 2.8 CRD engine code R2816K4 then it is this one
Stage 1 - Bolts 1 -18 = 30 Nm
Stage 2 - Bolts 1 -10 = 75 deg
Stage 3 - Bolts 11 - 18 = 50 deg
Stage 4 - Bolts 1 - 18 - 75 deg

Sequence
aa5xdif9xa+aaaaaaelftksuqmcc

If it is the Grand Cherokee then they fit 3.0 CRD, 4.7, 5.7 and the 6.1 SRT-8 engines. I can supply the details if needed. I hope that helps you.

Feb 04, 2015 | 2008 Jeep Cherokee 2.5

1 Answer

When you replace the head gasket on a kia do you also need to replace the bolts?


Most likely, many others with aluminum? heads have what are called "stretch" bolts, a one time use to maintain the correct tention and the torqe calibration on instalation.

Aug 06, 2013 | 2001 Kia Spectra

1 Answer

What is the torque of nissan urvan qr25 engine head bolts


nissan urvan 2006 engine head bolt torqe

Jan 31, 2012 | Cars & Trucks

1 Answer

HI HILUX SURF WITH 2LT DIESEL ENGINE CAN I GET CORRECT TORQE FOR. 1-TORQE FOR HEAD BOLT? 2-TORQE FOR CON ROD BEARING BOLT? 3-TORQE FOR MAIN BEARING BOLT?


Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Jun 30, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


22 - 24 ft. lbs. for the rod caps and....
110795143Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:
  • Do not reuse the old cylinder head bolts.

May 31, 2010 | 2004 Kia Rio

1 Answer

U' m repairing the head on 05 kia rio timing belt slipped and juped time bending all the valves Now putting the head back on I need to know if the head bolts neeed to be replaced and how to torq


try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 19, 2009 | 2005 Kia Rio

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...