Question about Cars & Trucks

1 Answer

Dear brothers ! 2006 toyota mark x what is error code B2281 p signal malfunction? about this case tell me,plz? help!!!

I always try car repairing work!

Posted by on

  •  ye gaung lay
    ye gaung lay Oct 29, 2012

    help me brothers in fixya?

  • Rohoma Fathi Jun 02, 2013

    I have the same code and need help too

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Cars & Trucks Master
  • 2,620 Answers

This code is for the right rear seat forward switch circuit perfomance.

Posted on Oct 29, 2012

Testimonial: "thanks bro!"

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 204 Answers

SOURCE: I have a 2005 Toyota

THAT IS NO WARRANTY GENERALLY DUE TO THE AGED OF THE CAR , OFTEN ITS AN ABS SENSOR THAT GONE BAD

Posted on Oct 12, 2010

Murphybanton
  • 2004 Answers

SOURCE: My Toyota Crolla 98 cars' Malfunction indicatore lamp is on, .

It simply means there might be an issue you need to resolve but not necessarily a problem.

Take it for a scan is the best advice but you could also remove your battery terminal for 5 minutes and replace back.

Rate this please.

Posted on Apr 03, 2009

messstat
  • 365 Answers

SOURCE: 2006 PT Limited. Engine Malfunction light is on.

First off, it's NOT the crank position sensor...Unless you've pulled the motor recently!
Get down to Advance Auto Parts and buy a car of "SeaFoam" ($9) and add it to your tank per instructions...drive AT LEAST 100 miles...problem should go away.
If not, your O2 sensor in the exhaust (x3) is faulty...look to spend $200-400 depending on your mechanic...DO NOT GO TO THE DEALER!
Good Luck

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a B2281 code where should I start


Right turn switch short to ground. B2281 OBD Code Description

Feb 06, 2015 | 2011 Toyota Land Cruiser

1 Answer

My car toyota srs porablm


air bags
get the bags scanned,
read the FSM on bags yet< (factory service manual)
or at alldata.com, DIY.
in what country? , did you read the TSB recall yet>?????
huge recall.
where is this 31 code? at>?
Trouble Code: B1000/31 (1.8L L4 VIN R Auto)
Airbag ECU Malfunction * Airbag sensor assy center

remove battery neg lug before touching any SRS parts.
B1000/31; Center Airbag Sensor Assembly Malfunction (2006 Corolla From 07/2005) DESCRIPTION The center airbag sensor assembly consists of a deceleration sensor, safing sensor, drive circuit, diagnosis circuit, ignition control, etc.
If the center airbag sensor assembly receives signals from the deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1000/31 is recorded when a malfunction is detected in the center airbag sensor assembly.

If only DTC B1000/31 is output, do not clear the DTCs, replace the center airbag sensor assembly.
If any DTCs other than DTC B1000/31 are also output, troubleshoot those DTCs first.


use a real scan tool
and see all errors.
if not you guess wrong.




Feb 02, 2015 | 2006 Toyota Corolla

1 Answer

NO POWER TO SPARK PLUG toyota noah 2003 showing error code p0105, p0110, p0115. some one help me plz.


code p0105 refers to manifold absolute pressure (MAP) sensor/ barometric pressure (BARO) sensor--circuit malfunction===causes --wiring---MAP sensor--BARO sensor--ECM
code p0110 refers to intake air temperature (IAT) sensor--circuit malfunction===causes---wiring ---IAT sensor--ECM
code po115 refers to engine coolant temperature (ECT) sensor--circuit malfunction===causes---wiring--ECT sensor---ECM

Dec 25, 2013 | Cars & Trucks

1 Answer

Toyota corolla 1997 engine code p1300 ignitor circuit malfunction #1 car starts after 2 minutes will stop


Error Code P1300/ 14. Igniter signal malfunction No.1
Problem Areas:
IGNITION SIGNAL--NO "IGF" SIGNAL TO ECU
--IGNITER/IGNITER CIRCUIT
--IGNITER AND IGNITION COIL/CIRCUIT
--IGNITION AMPLIFIER/ DISTRIBUTOR.
--ECU

Oct 18, 2013 | Toyota Corolla Cars & Trucks

1 Answer

My cd's are stuck in my cd player in my 2006 toyota avalon. error code 3


This type of malfunction usually requires removal of the unit and disassembly

Jan 19, 2013 | 2004 Toyota Camry

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

2 Answers

Fault code 21 and 42 on 98 toyota corolla,can u tell me what sensor it is?


21 Oxygen sensor voltage remained between .35 and .7V
continuously despite feedback correction
42 Vehicle speed sensor output doesn't reach the computer

Info From:


http://www.corolland.com/repairs.html

Sep 15, 2010 | 1998 Toyota Corolla

1 Answer

Replaced the hybrid battery after that car doesnt not start. it gives code B2281.


Well, you wanted it for free......so here it is......the code stands for a P signal malfunction...relating to the Push Button Start system.......check this pdf file to narrow it down....
http://hybrids.ru/PriusNHW20/rm/rm1076e/m_05_2143.pdf

Aug 26, 2010 | Toyota Camry Cars & Trucks

Not finding what you are looking for?

Open Questions:

0 Answers

My 2007 Dodge Ram 1500 4X4 with the 5.7 Hemi engine threw me for a loop yesterday. Stay with me on this as it gets weird. First the engine shut down as did the tach. Then started back up as I coasted down the road (in Mexico of all places). Next it did the same thing again but in addition the cruise would not work and the overdrive didn't work (usually @ 2000 RPM at 60 then the tach showed 2500 RPM. Sure enough by engaging the button on the shifter no change in RPM. Then the engine shuts down, tach inop, OD inop, cruise inop, and the check engine light comes on. Then (it gets better) all of the above happens and I coast to a stop. Shut the ignition off, turned it back on and the cruise works, the overdrive works but the engine shuts down BUT the tach is now working. Long story longer I limp back to Green Valley, AZ with the truck and run the codes and the only code is a P0300 (random cylinder misfires within a predetermined period of time (No S#@t). Also was able to determine the following codes. P0339 (crankshaft position sensor intermittent, P1128 Closed loopfueling not achieved-bank 1 as well as P1129 (the other bank). I'm leaning towards replacing the ECM. Could it possibly be the IPCM (integrated power control module)? OR do I have a loose connection somewhere? It seems the problem gets worse when I go over rough roads (about all of Mexico is ROUGH roads. LOL) Call me "Looking for answers before I pull the rest of my hair out".

May 26, 2018 | Dodge Cars & Trucks

Cars & Trucks Logo

Related Topics:

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13735 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...