Question about 2011 Cadillac SRX
Battery needs replaced
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
Well according to my mitchell manuel you don't have to.here is the procedure.
1. open the hood.
2.Remove the push-pin retainer's that secure the top of the upper facia and grill assembly to the upper tie bar to allow the upper facia and grill assembly to flex forward.
3. remove ther bolt and push-pin retainer that secures the top of the headlight assembly to the upper tie bar.
4. Gently pull the upper facia and grill assembly forward to access the bolt on the inboard side of the headlight assembly
5. Pull the headlamp assembly straight out to disengage the the snap in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the inboard assembly clears the front facia.
6. pull the assembly out and away from the veh.From there you'll be able to access bulbs.
be careful not to touch the bulb with fingers or oil in skin will blow bulb.
Posted on Aug 19, 2009
Check fuel pressure with pressure tester, test power coming from coil packs to make sure that all spark plugs are getting power. You can test relays and fuses with an ohmmeter.
GM does have an anti-theft device that is know to cause problems.
First put in key and leave on for exactly 10 minutes, then as soon as the anti-theft light turns off, the immediately start the car.
Posted on Sep 16, 2009
If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.
Posted on Dec 15, 2009
Tips for a great answer:
Oct 26, 2016 | 2011 Cadillac SRX
Feb 03, 2016 | Cars & Trucks
Apr 14, 2015 | 2007 Cadillac SRX
Dec 12, 2014 | 2011 Cadillac SRX
Jul 17, 2014 | 2011 Cadillac SRX
Feb 28, 2011 | 2011 Cadillac SRX
Oct 24, 2010 | 2005 Cadillac SRX
Nov 13, 2009 | 2005 Cadillac SRX
248 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: