Question about 1990 Dodge Ramcharger

Open Question

1990 dodge 150 heater core replacement - 1990 Dodge Ramcharger

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 141 Answers

SOURCE: 2000 dodge grand caravan rear heater core tubes need replacing

a lot of pain and heart ache. even on a rack they are a pain . check with your dealer there wae a recall on them for failing its worth the phone call to see kdc744

Posted on Feb 08, 2009

Ad
emissionwiz
  • 76164 Answers

SOURCE: 2002 DODGE 2WD HEATER CORE REPLACEMENT

first off, disconnect your battery for at least 30 min before touching any plugs or harnesses. next, bleed your A/C and disconnect the quick connects that go inside the firewall. drain your coolant, and disconnect hoses from firewall. note a certain bolt with nut on it that is going to the inside of the firewall, you'll need to take that off when you get to the airbox inside the truck which houses your heater core. next, take off the pillar handles next to the windshield, then pop off the plastic dash panel with defroster vents. there are a few bolts up there that need to be taken out all the way across. next, take off your glove box. remove plastic below the drink carrier. there are 2 bolts there on left and right once you remove the plastic. there's a yellow or red AirBag plug which you may or may not need to disconnect later. next, drop down the whole steering wheel column. 4 bolts I believe. look up under there on both sides, you will see a 2inch piece of tubing that goes from each side of the truck. your dash and everything you see in front of you is connected to that tube. find on each side of the truck where that tube is mounted to the body with brackets. There are 2-3 bolts on each side I think. When you get those out, and the steering wheel is sitting in the seat or on the floor, the whole dash and panel should tilt and lay on the seats. there are wires from your a/c controls and radio which you'll have to disconnect and some various other wires as well. I also think you'll have to disconnect a harness plug with bolt in it on the drivers side. (white) after you've done all that and don't have the dash and panel in a bind with wire hangups you can now get to the air box. I don't remember how many bolts, but don't forget the one in the engine bay going to it also. get the box unbolted, then roll it up, remove 2 clips holding the heater core in, replace heater core and do this whole process backwards. Hopefully you didn't lose any screws or bolts. charge your a/c, replace coolant, make sure all plugs are connected before connecting power. Should save you $400-$500 in labor.

Posted on Mar 25, 2009

  • 154 Answers

SOURCE: 95 dodge dakota heater blower not working

It has been a long time since I've replaced one of those. From what I remember you don't have to go through pulling the heater box out. You do need to remove the glove box assembly. Look up under the passenger side of the dash. If you see the bulge of the motor/cover hanging straight down then remove the cover and the motor will be there. If you don't see that then te motor is mounted horizonally. If that is the case then the fresh air door assembly will need to be removed and it is behind that.
Here is a quick check to see if the motor is bad. Thump the bottom of the heater box by the passenger's feet. if the motor comes alive or makes noise then it is bad. Also check the fuse and make sure that it doesn't work on any speed. (the resistor would prevent operation on only one speed or more but generally not all speeds)

Posted on Apr 05, 2009

LEFTY64
  • 69 Answers

SOURCE: Need to replace the heater core in a 1995 Dodge Grand Caravan SE

1991-95 Models

  1. Disable the air bag system by disconnecting the negative battery cable.
  2. Have the system discharged by a qualified professional mechanic using an approved recovery/recycling machine.
  3. Drain the cooling system.
  4. Remove the steering column cover and left and right side under panel silencers.
  5. Remove the center bezel by unclipping it from the instrument panel.
  6. Remove the accessory switch carrier and the heater/air conditioning control head.
  7. Remove storage bin and lower right instrument panel.
  8. Disconnect the blower motor lead under the right side of the instrument panel.
  9. Remove the right side 40-way connector wiring bracket.
  10. Remove the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  11. Disconnect the vacuum lines at the brake booster and water valve.
  12. Clamp off the heater hoses near the heater core and remove the hoses from the core tubes. Plug the hose ends and the core tubes to prevent spillage of coolant.
  13. If equipped with air conditioning, remove the H-valve and condensation tube.
  14. Disconnect the temperature control cable and vacuum harness at the connection at the top of the unit.
  15. Remove the retaining nuts from the package mounting studs at the firewall. Disconnect the hanger strap from the package and rotate it aside.

To install:
  1. Remove the temperature control door from the unit and clean the unit out with solvent. Lubricate the lower pivot rod and its well and install. Wrap the heater core and/or evaporator with foam tape and place in position. Secure with the screws.
  2. Assemble the unit, making sure all vacuum tubes are properly routed.
  3. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  4. Connect the hanger strap from the package and rotate it aside. Install the 2 brackets supporting the lower edge of the heater housing. Connect the blower motor wiring, resistor wiring and the temperature control cable.
  5. Install the retaining screws from the right side to the steering column. Install the instrument panel trim covering and reinforcement.
  6. Assemble the unit, making sure all vacuum tubes are properly routed.
  7. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  8. Connect the hanger strap from the package and rotate it aside. Connect the blower motor wiring and temperature control cable.
  9. Install the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  10. Install the right side 40-way connector wiring bracket.
  11. Install the lower right instrument panel and storage bin.
  12. Install the heater/air conditioning control head and accessory switch carrier.
  13. Install the center bezel to the instrument panel.
  14. Install the under panel silencers and steering column cover.
  15. Install the vacuum lines at the brake booster and water valve.
  16. Connect the heater hoses to the core tubes.
  17. Using new gaskets, install the H-valve and connect the refrigerant lines. Install the condensation tube.
  18. Have the system evacuated and recharged by a qualified professional mechanic, utilizing the proper equipment. Add 2 fl. oz. (59 ml) of refrigerant oil during the recharge. Fill the cooling system.
  19. Perform the Air Bag System Check procedures outlined in this section before connecting the negative battery cable.
  20. Connect the negative battery cable and check the entire climate control system for proper operation and leaks.

Posted on Apr 08, 2009

BPALepine
  • 61 Answers

SOURCE: Dodge Interpid Heater Core

There is so many steps required in this procedure. I would recommend purchasing a repair manual so that you have it on hand.

Posted on Apr 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1990 RAMCHARGER NEEDS HEATER CORE REPLACED, CAN YOU TELL ME HOW TO DO IT?


For heater core replacing procedure. I suggest you to go through this related help links.Its all complete step by step procedure: ----How to replace heater core for All car models?

Click the link below: ---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

--------------
How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

---------------
How to Remove Heater Core ?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html
Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------
To replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html------

How to replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html
----------This will help.Thanks.

Dec 21, 2010 | 1990 Dodge Ramcharger

1 Answer

I have a 1990 Camaro, I had the heater disconnected - cost was $150, they said to replace it with a new heater would be over $800 - is this a fair price ?- The car is not worth more than $1,000


if you mean to replace a heater core,
the heater core is about $40.00 from Autozone,So the $150.00 is labor,this job can be done in one hour and at shop rates today that would be $50.00,
you need to buy the heater core yourself and find another shop.

Jan 23, 2010 | 1990 Chevrolet Camaro

1 Answer

Heater hose diagram for 1990 dodge dynasty. The heater hoses where conected togather due to a bad heater coil that has now been replaced I need to know how to put heater hoses back where they go and I am...


remove the hoses at the temp conection inspect them to make sure they are good them follow the one that comes from the pump housing goes to the top of the heather core outlet and the return one to the bottom this may be a bit diferent if the engine is 6cyl or 4cyl.

Sep 08, 2009 | 1990 Dodge Dynasty

3 Answers

When heater is on i smell coolant


Hi

This is caused by a leak in either the heater core itself or the hoses connecting to the heater core.

Rust and corrosion can clog the tiny passages in your heater core. Sometimes the block becomes so severe that pressure builds up in the heater core causing it to spring a leak of coolant - enough to give off the smell you describe.

You can find examples of the heater core at this link
http://www.autopartswarehouse.com/shop_parts/heater_core/dodge/ram_50.html

Solution: Replace heater core or hoses depending on what you find.

Hope this helps. Please do rate this answer. Many Thanks.

Sep 01, 2009 | 1999 Dodge Ram

1 Answer

Does the dash need to be removed on a 1990 F-150 to replace the heater core?


No, just remove the glove box and then the plastic cover behind it. Once the cover is removed, you'll find your heater core.

Jun 07, 2009 | 1990 Ford F150

1 Answer

How to fix heater core 1992 dodge spirit


Take my word for it, you don't want to fix it. Take it to your local radiator shop and have someone put a heater core in it for you. You will be way better off. I've done these before and it takes about 6- 8 hrs. The whole dash has to come out. The steering column has to be dropped. If I had one of those cars that needed a heater core, I would take it somewhere and have it done. Phil

Jan 20, 2009 | 1990 Dodge Spirit

2 Answers

1999 Dodge Durango is not getting enough heat. Replaced thermostat and still not much heat and the temp gauge only goes to about 150 degrees. Please help!!! My wife is so COLD!!!!


Make sure you chek out the coolent level and if the level is fine, the next step to go is the heater core. it should be one of these 2 solutions!!

Jan 17, 2009 | 1999 Dodge Durango

1 Answer

Heater core 1990 Ford F-150


I believe this is the easiest heater core ever invented. If it is like the 1986 model. I believe it is. You take out the glove box door. The heater core is right there under a cover in the duct work.

Oct 11, 2008 | 1990 Ford F150

Not finding what you are looking for?
1990 Dodge Ramcharger Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...