Door mirror glass replacement-P38

Question edited for clarity and toss in some CAPS.
Question moved to model category.

Exterior Mirror Replacement Glass for CITROEN C2 (2003 ...

Amazon.ca https://www.amazon.ca > Exterior-Replacement-CITR...

1.Remove all existing mirror glass from the mirror assembly plastic backing plate. 2.Clean the backing plate with rubbing alcohol and clean the back of the new ...
$70.50 · ‎In stock

Car Wing Heated Mirror Glass Lens, for Citroen C3 ...

Amazon.ca https://www.amazon.ca > Heated-Mirror-Glass-Citroen...

Easy to install: The damaged mirror can be replaced directly, and an alternative to replace the entire mirror housing is provided. If you have any questions, ...
$69.05

Low Price Guarantee on citroen c3 picasso Wing Mirror ...

Car Door Mirrors https://www.cardoormirrors.com > citroen > c3-picass...
Low Price Guarantee and Free Delivery on High Quality citroen c3 picasso Wing Mirror Glass, Replacement citroen c3 picasso Wing Mirrors and Stick on Mirror ...
£4.99 Videos
..

Power Dr Mirrors Diagnosis & Testing

Removal & Installation
Motor

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove or disconnect the following:
   
   Disconnect the negative battery cable. The mirror inside cover trim The door panel The electrical connector to mirror motor The nut attaching mirror assembly to door frame The outside rear view mirror
   
   

   Fig. Removing cover trim and nut
   Removing cover trim and nut
   
   

   Fig. Removing mirrored glass from assembly
   Removing mirrored glass from assembly
   

3. Remove the mirror glass:
   1. Fold the mirror glass forwards and inwards as illustrated.
   2. Grasp and pull the mirror glass lengthways until it releases.
   3. Work the glass out.
   
   
4. Remove electric motor:
   1. Remove the 3 screws from behind the mirrored glass.
   2. Separate the connectors
      NOTE Remember the positions of the connectors.
      
   3. Remove the mirror motor.
      
      

      Fig. Removing connectors and screws holding mirror motor
      Removing connectors and screws holding mirror motor

   
   

To install:

1. Install or connect the following:
   
   The electric motor The electrical connections The 3 screws that go behind the mirror Install the terminal pins Fold out the mirror mounting on the motor Hook the mirror glass into the inner mounting Press the mirror glass into place. Place mirror in position in door
   
   

   Fig. Reattaching mirror and electric motor connectors
   Reattaching mirror and electric motor connectors
   

2. Install or connect the following:
   
   The nut attaching mirror assembly to door frame The connector The door panel The mirror inside cover trim The negative battery cable
   

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.

1. Remove the door handle bezel.
   • Use service notch.

1. Remove the window control switch plate.
   • Use service notch and disconnect the electrical connectors.

1. CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   Remove the two bolts and three screws, and remove the door trim panel.

1. Remove the weather shield.

1. Disconnect the exterior mirror electrical connector.

1. Remove the exterior mirror.
   • Remove the nuts.

1. To install, reverse the removal procedure.
   • Install top nut first.

---
Exterior Mirror Motor Removal and Installation

1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.

1. Disconnect the heated mirror electrical connectors.

1. Remove the exterior mirror motor screws and exterior mirror motor.
   • Disconnect the electrical connectors.

1. To install, reverse the removal procedure.

Outside Mirrors REMOVAL & INSTALLATION Standard

1. Remove the door trim panel and detach the inner panel water deflector. With the glass in the down position, pull out the front portion of the glass run weatherstrip. Fig. 1: Unfasten the attaching nuts from the mirror base studs, then remove the mirror

1. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler, then rotate retainer rearward.
2. Remove the noise control patch to gain access to the screw at the belt, then remove the screw.
3. Remove the filler attaching screws at the top front of the window frame, then remove the mirror and filler from the door.
4. Remove the attaching nuts from the mirror base studs, then remove the mirror. To install:
   
5. Be sure that the mirror gasket is aligned.
6. Replace the mirror and filler on the door. Install the filler attaching screws at the top front of the window frame. Attach the nuts to the mirror studs and tighten.
7. Install the screw at the belt, then insert the noise control patch.
8. Insert the retainer, then install the attaching bolts and screws to the front glass run channel lower retainer to filler.
9. Replace the front portion of the glass run weatherstrip, insert the inner panel water deflector, then reinstall the door trim panel.

Manual Remote

1. Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector. NOTE: Right side remote mirror may require detaching part of the instrument panel.
   
2. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
3. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
4. Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
5. Remove the filler attaching screws at the top front of the window frame.
6. Remove the mirror base with mirror and cable assembly from the door.
7. Remove the mirror to filler attaching nuts and remove the mirror and cable from filler. To install:
   
8. Be sure cable is routed around front glass run channel retainer and installed to clip.
9. Install and connect the cable to the filler.
10. Attach the filler nuts to the mirror, then tighten to 72 inch lbs. (8 Nm).
11. Install the mirror base with the mirror and cable assembly to the door.
12. Insert the filler attaching screws to the top of the window frame, then install the screw to the belt.
13. Secure the noise control patch.
14. Attach the bolts and screws to the front of the glass run channel lower retainer and filler.
15. Install the glass run weatherstrip.
16. Attach the inner panel water deflector, door trim panel and mirror remote control escutcheon.

Electric Remote

1. Disconnect the negative battery cable.
2. Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector and the electrical connector for the mirror. NOTE: Right side remote mirror may require detaching part of the instrument panel.
   
3. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
4. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
5. Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
6. Remove the filler attaching screws at the top front of the window frame.
7. Remove the mirror base with mirror and electric connector from the door.
8. Remove the mirror to filler attaching nuts and remove the mirror and electric wire from filler.
9. To install, reverse Steps 1 through 6. Be sure electric wire is routed around front glass run channel retainer and installed to the clip. Tighten the nuts to 72 inch lbs. (8 Nm).
10. Connect the negative battery cable, then reset the clock, radio and any other accessories if required.

does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

here's repair procedure

Window Regulator, Front Door, Explorer Removal
WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.

1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .

Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation

1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .

1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.

1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .

1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
   

1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
   

1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.

1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .
   
   Trim Panel, Front Door, Explorer Hi-Series Four-Door
   
   

1. Remove inside door belt weatherstrip and glass stabilizer.

1. Remove front door window glass as described in this section.

1. Remove two nut and washer assemblies attaching the equalizer bracket.

1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .

1. Remove window regulator electric drive and front door window channel bracket from vehicle.

1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .

1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.
   
   
   
   

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.

1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.

1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
   

1. Install equalizer bracket.

1. Install inside door belt weatherstrip and glass stabilizer.

1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.

1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.

1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Hi

You need to put on a pair of gloves, and safety glasses. (Safety First !)
Prise off the broken mirror from the plastic base that it is stuck too.
Give the plastic a clean with nail polish remover or similar.
Peel off the backing on new mirror glass, and carefully stick it on.

Good Luck !

Don´t forget to FixYa Rate Me Please !

John.

If you need to replace the entire mirror - it's a little involved. First you need to take the upper extension panel off from behind the mirror (black triangle) - just pull it of starting at the top. It will snap back on later. Next - remove the different screws holding the door panel in place (not the ones behind the mirror yet!) One is under the handle (pull it out and pull out the filler panel - small plastic thing that has a hole to pry it out). Then take off the rear red light - also pops off - and remove that screw. Finally - pick up the rubber filler where your fingers pull the door shut and remove these torx bolts.

Now is the tricky part. Snapp off the entire interior panel. It will pop off - but very difficult. It will sound like it is breaking! Start at the outer bottom corner - and use a door panel remover tool - check Amazon or E-bay - to keep from breaking things. Pull it out from all around the bottom and sides and then lift it up over the door lock. It good to have a friend help here. The panel will still be held on by a cable - that is your door release - leave it alone and let the panel hang by it (or better, put a box under it to rest on).

Now...remove the three bolts holding the mirror on - have a friend help hold the mirror while you do this or it will scratch your new car! Since the inner panel is off - you can also disonnect the mirror plus and remove it. It sounds silly - but the only reason to remove the door panel is to unplug it!

Get you new mirror and reverse the steps.

If you are just replacing the glass (non-heated) - get a replacement from the dealer. Adjust the mirror all the way to the inside and reach behind and pop it off. CAREFUL - put tape over the entire glass as it will likely break even more! Remove your connectors if heated - and replace (and reconnect) with your new glass. It just pops back on!

Replacing glass is easy - just be careful of cheap imitations on e-abay). And never use cheap flat glass on the passenger side! The DOT has special requirements for mirror glass - buy it from gmpartsdirect.com or your local dealer.

kb

Hi,
I have a Mazda 6 Estate - I've just had the glass out of my mirror this evening, because my mirror heater is not working - there was a bunch of wires into the mirror unit - two of which went to spade connections on the back of the mirror.
The glass itself is on a plastic mount. The mount and the glass should just lever/pull out - that's what I did with mine - I was worried it was going to break though, it took substantial force! Once out I could see a plastic rectangle with rounded corners that it had been clipped onto. It clipped back into place with out any difficulty (on mine there is a wire guide behind the glass - just make sure that you haven't bent it upon removal - I had, but the pliers straightened it again).