Question about 2006 Ford Ranger

Open Question

Where is the egr valve on a 2006 ford ranger stx

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

Ad
davesmith_37
  • 94 Answers

SOURCE: where is the pcv valve located on a 2003 ford ranger

  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Posted on Feb 27, 2009

    csmock132
    • 4669 Answers

    SOURCE: location of the EGR valve/DPFE pressure sensor

    What engine? It won't cause any running problem but gas milage will be effected just because the light is on. Ford computers change parameters when the light is on and mileage will drop 1-2 miles per gallon.

    Posted on Jun 21, 2009

    daves944
    • 1050 Answers

    SOURCE: egr valve replacemebt

    It's bolted onto the intake, next to the throttle body. If you look into the engine compartment and see the oil dipstick, look up and to the right. It will have a steel tube coming up to it from the exhaust. Why do you want to replace it? They rarely fail. EGR problems (codes) on Fords are usually caused by the Differential pressure feedback sensor.

    Posted on Jan 24, 2010

    • 1 Answer

    SOURCE: EGR VALVE ON 96 FORD PROBE SE

    If it's a 2.0L, 5 speed (1994-7) there are two DPFE solenoids (both w/ 3 vacuum ports) near the oil filter, which control the EGR valve. They are discontinued and impossible to find except on junked cars. (FORD #'s K5T44093-4)
    I have to junk my 1996 Probe if I don't find them - Missouri emissions.

    Posted on Mar 03, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    My 2006 Ford Ranger w/ 3.0 v6 vhexk engine lite is on . My mechanic says his machine that he plugs in says its the egr valve but he says 2006 doesnt have one . Whats the correct answer?


    I went google and typed in-- location of egr valve on ford 3L v6 engine 2006--- and got pages showing exactly where it is
    the model that the engine is doesn't really matter as it is the assembled engine that has the egr valve, so 3L v6 engine will have one regardless if it is a ranger , taurus or what ever.
    part number is 18734-05059775 and has a listed price of $52.33
    ( parts geek.com)
    another point is that with every code there are several causes for a code number
    I might suggest an accredited service center with experience on your make of vehicle might be a better place to go

    Dec 17, 2016 | Ford Cars & Trucks

    1 Answer

    Either code 4000 or 1400 on 2002 ford ranger 4.0 ltr v6. the right code should equate to the egr valve. I have replaced the egr valve but check engine light comes on again after reset showing same code.


    code p1400 is a DPF EGR sensor CIRCUIT LOW VOLTAGE detected. most likely is a problem with the wiring to the egr or dpfe sensor. the pinpoint tests for code p1400 instruct you to test all wiring before replaceing the egr or dpfe sensor

    Jan 19, 2011 | 2002 Ford Ranger Regular Cab

    1 Answer

    Where is the egr valve located on a 1994 Ranger 4.0L V6?


    If your ranger has a egr valve it will be on the driver's side of the upper intake plenum (the top aluminum housing, very top of the motor) and about centered on the plenum.in 1994 I have seen Rangers with and without a egr valve. I believe it depends on if its California emissions or not.

    Dec 31, 2010 | Ford Ranger Cars & Trucks

    1 Answer

    My 2006 ford ranger is running very rough. i changed the plugs and plug wires but that didn't help. please help!


    Try replacing the fuel filter then remove and clean the EGR valve also check the purge canister valve to see if it is operating correctly. and if all else fails rent a fuel pump tester from auto-zone or Schucks and test fuel rail pressure.

    Aug 14, 2009 | 2006 Ford Explorer Sport Trac

    1 Answer

    My egr valve


    driver side front of intake hidden by black plastic cover look for small hose coming from exhaust to egr valve

    May 19, 2009 | 1993 Ford Ranger SuperCab

    1 Answer

    Egr valve


    The EGR Valve is #4:

    0521ced.gif

    Please don't forget to rate!

    May 19, 2009 | 1993 Ford Ranger SuperCab

    2 Answers

    Need location of the erg sensor 2000 ford ranger


    The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

    The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

    The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

    Feb 24, 2009 | 2000 Ford Ranger SuperCab

    2 Answers

    Location of the egr sensor on 2000 ford ranger


    The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

    Feb 24, 2009 | 2000 Ford Ranger SuperCab

    Not finding what you are looking for?
    2006 Ford Ranger Logo

    Related Topics:

    53 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    fordexpert

    Level 3 Expert

    5530 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...