Question about Renault 181
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls
Posted on Sep 23, 2009
Most likely to be a faulty resistor block, which has 3 resistors and a thermal fuse controlling fan speeds 1,2 and 3, maximum speed 4 by-passes the resister block. It may also be poor electrical connections to the resistor block caused by overheating. Renault ask for approximately £350 to carry out repairs, a replacement resistor block will cost £50. If you decide to carry out the repairs yourself, be advised that if you are not competent to carry out such work you, could cause electrical damage or worse an electrical fire.
Posted on Nov 14, 2009
a renault ,real euro car this one ,no problem here at all ,bring the pistons to TDC the bring back a bit so no piston is at the top ,mark it whilst its at the top with a thin white paint mark on the sprocket ,then back it down a bit .fit head because i sure the head bolts are under the cams ,then fit cams and make sure the inlet and exhaust valves are closed on no1 .no4 should be open with the cam lobes pointing down ,now look for the timing marks,they could be a lug on the cam pointing at something or a slot on the back of the camshaft that has to horizontal with the head ,or even a hole in the front pulley that aligns with a hole indent in the head that has an 8mm bolt push in to hold gear wheel in place -then when you find the marks bring the bottom sprocket back to the mark ,the actual mark is on the flywheel as i remember a special tool with a spring loaded pin to locate flywheel is used ,the fit the belt ,seem to remember a white line here on the belt that aligns with the cams a well ?? look iam old and i forget things ,then make sure you turn engine over twice on bottom pulley with a ratchet to ensure valves clear before starting -
Posted on Jan 02, 2010
this exact problem on a megane coupe is caused by a small air pipe that connects to a 2 inch wide black box that is located under the bonnet near the windscreen on the passangers side. the zigzag light indicates an electrical fault (in this case lack of compression and will affect your revs) if you find this pipe and it has snapped off. the reason for this may be that your engien is lose and moves. grab the engien with 2 hands and see if you can wobble it with allot of play. if so your engien mountings need replaceing. you may also experiance juddering in low gears
Posted on Mar 04, 2010
Tips for a great answer:
Aug 23, 2016 | 2003 Renault Megane
Aug 21, 2016 | 2003 Renault Megane
Mar 23, 2016 | Renault Cars & Trucks
Dec 29, 2014 | 2006 Renault Scenic 1.6
Aug 20, 2013 | 2001 Renault Sportwagon
Oct 27, 2011 | 2000 Renault 181
Aug 25, 2010 | 2003 Renault 181
Mar 05, 2009 | 2006 Renault Sportwagon
37 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: