Question about 1997 Dodge Intrepid

1 Answer

Engine light on

Low power to temp sensor need to know what controls voltage to temp sensor

Posted by on

  • Anonymous Jan 14, 2009

    1997 Dodge Intrepid....no heat, blower works, engine runs cool, put new thermostate in and still no heat. Engine lite and air bag lite stays on, bought 2nd. hand

  • John Jon May 11, 2010

    what is your fault code??PO???

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 350 Answers

Take it in for a code read.
Advanced Auto will usually do this for free!
Good Luck!

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What can cause trouble code p0118 engine coolant temp sensor ( high voltage input ) 99 intrepid 2.7 v6


The engine coolant temperature (ECT) sensor is a variable resistor, that measures the temperature of the engine coolant. The ECT sensor has a signal circuit and a low reference circuit. The engine control module (ECM) supplies 5 volts to the ECT signal circuit and a ground for the ECT low reference circuit. When the ECT is cold, the sensor resistance is high. When the ECT increases, the sensor resistance decreases. With high sensor resistance, the ECM detects a high voltage on the ECT signal circuit. With lower sensor resistance, the ECM detects a lower voltage on the ECT signal circuit. If the ECM detects an excessively high ECT signal voltage, which is a low temperature indication, DTC P0118 sets. You have A bad coolant temp sensor or a wiring problem !

Aug 05, 2015 | Cars & Trucks

1 Answer

Can you tell me the location of code reader 1991 capri ?


1991 is pre-OBD2. code readers will not work.
sorry.
however, all is not lost. Many cars have an alternate way of reading codes from the computer.
Toyota has a block under the hood and you short couple wires together and count engine light flashes
Chrysler you can turn the ignition key on and off a few times and count engine light flashes
in your case for GMs from 1982 to 1995
1: find the 12 pin connector under the dash and short the upper two rightmost terminals.
with the ignition "ON" and engine not running. The system will enter the diagnostic mode. In this mode, the computer will display a Code 12, three consecutive times, by flashing the "CHECK ENGINE", "SERVICE ENGINE SOON" or "MALFUNCTION INDICATOR LAMP" or light. A Code 12 consists of one flash, a short pause, then two flashes in rapid succession.
2:. After Code 12 is displayed, any stored trouble codes will be displayed by flashing the "CHECK ENGINE", "SERVICE ENGINE SOON" or "MALFUNCTION INDICATOR LAMP" light. All codes are displayed 3 times each then a code 12 will repeat. In the diagnostic mode, the computer will also energize all computer controlled relays and solenoids.

Tech -- GM 2 Digit codes for 82 and up (non OBD-II)
code - code definition
12- diagnostic mode
13- 02 sensor or circuit
14- coolant sensor or circuit/ high temp indicated
15- coolant sensor or circuit/ low temp indicated
16- system voltage out of range
19- crankshaft position sensor or circuit
21- throttle position sensor or circuit- voltage high
22- throttle position sensor or circuit- voltage low
23- mixture control (m/c) solenoid or circuit (carbureted models)
23- manifold air temperature (mat) sensor or circuit (1990 and earlier models)
23- intake air temperature (iat) sensor circuit (fuel-injected models)
24- vehicle speed sensor (vss) or circuit
25- manifold air temperature (mat) sensor or circuit - high temperature indicated (1990 and earlier models)
25- intake air temperature (iat) sensor or circuit - high temperature indicated (1991 and later models)
26- quad driver module circuit
27- quad driver module circuit
28- quad driver module circuit
29- quad driver module circuit
31- park/neutral position (pnp) switch circuit
32- baro sensor or circuit (carbureted models)
32- egr circuit (fuel-injected models)
33- manifold absolute pressure (map sensor signal voltage high
33- mass air flow (maf) sensor or circuit - excessive airflow indicated
34- manifold absolute pressure (map) sensor signal voltage low 34- mass air flow (maf) sensor signal - low airflow indicated
35- idle speed control (isc) switch or circuit (shorted) (carbureted models)
35- idle air control (iac) valve/ circuit
38- brake switch circuit
39- torque converter clutch (tcc) circuit
41- no distributor signals to ecm, or faulty ignition module ( carbed models)
41- cylinders select error- mem-cal or ecm problem ( fuel-injected models
41- cam sensor circuit (3.8 engine)
42- bypass or electronic spark timing (est) circuit
43- low voltage at ecm terminal l (carbureted models)
43- knock sensor circuit
44- oxygen sensor or circuit - lean exhaust detected
45- oxygen sensor or circuit - rich exhaust detected
46- power steering pressure switch circuit
48- misfire diagnosis
51- prom, mem-cal or ecm problem
52- calpak or ecm problem
53- egr fault (carbureted models only)
53- system over-voltage (ecm over 17.7 volts)
54- mixture control (m/c) solenoid or circuit (carbureted models)
54- fuel pump circuit (1986 and later models)
55- oxygen sensor circuit or ecm
55- fuel lean monitor (2.2l engine)
61- oxygen sensor signal faulty (possible contaminated sensor)
62- transaxle gear switch signal circuits
63- manifold absolute pressure (map) sensor voltage high (low vacuum detected)
64- manifold absolute pressure (map) sensor voltage low (high vacuum detected)
66- pressure sensor or circuit air conditioning

May 20, 2014 | 2002 Subaru Forester

1 Answer

What does codes 64 63 11 09 and 21 0n 2005 dodge stratus mean


CODE 11 No distributor referene signal detected during engine cranking....Check circuit between the distributer and the pcm.

CODE 12 Problem with battery connection.Direct battery input to pcm disconnected within the last 50 ignition key-on cycles.

CODE 13** Indicates a problem with map sensor vacuum system.

CODE 14** map sensor voltage to high or to low.

CODE 15** Problem with vehicle speed sensor signal.No vss signal detected during road load conditions.

CODE 17 Engine is cold to long.Engine coolant temp stays below normal operating temp(check thermostat).

CODE 21** Problem with oxygen sensor signal circuit.Sensor voltage to computer not fluctuating.

CODE 22** Coolant sensor voltage to high or to low.Test coolant temp sensor.

CODE 23** Indicates that the air temp sensor input is below the minimum acceptable voltage or sensor input is above the acceptable voltage.

CODE 24** Throttle position sensor voltage to high or low.Test the tps.

CODE 25** Idle air control (IAC) valve circuits.A shorted condition is detected in one or more of the IAC valve circuits.Or a vacuum leak has been detected.

CODE 27 One of the injector control circuit output drivers does not respond properly to the control signal.Check the circuits.

CODE 31** Problem with canister purge solenoid circuit.

CODE 32** An open or shorted condition detected in the EGR solenoid circuit.Possible air/fuel ratio imbalance not detected during diagnosis.

CODE 33 Air conditioning clutch relay circuit.An open or shorted condition in the compressor clutch relay circuit.

CODE 34 Open or shorted condition in the speed control vacuum or vent solenoid circuits.

CODE 35 Open or shorted condition detected in the radiator fan low speed relay circuit.

CODE 37** Open or shorted condition detected in the torque converter part throttle unlock solenoid control circuit.

CODE 41** Problem with charging system.An open or shorted condition detected in the generator Field control circuit.

CODE 42 Fuel pump relay or auto shutdown relay (ASD) control circuit indicates an open or shorted condition.

CODE 43** Multiple cylinder misfire detected.Peak primary circuit current not achieved with the maximum dwell time.

CODE 44 Battery temperature sensor volts malfunction.Problem with the battery temperature voltage circuit in the pcm.

CODE 46** Charging system volts to high>Computer indicates that the battery voltage is not properly regulated.

CODE 47** Charging system voltage to low.Battery voltage sense input below target charging voltage during engine operation and no significant change in voltage detected during active test or alternator output.

CODE 51** Oxygen sensor signal input indicates lean air/fuel ratio condition during operation.

CODE 52** Oxygen sensor signal input indicates rich air/fuel ratio during engine operation.

CODE 53** internal pcm failure detected.

CODE 54** No camshaft position sensor signal from distributer.Problem with the distributer synchronization circuit.

CODE 55 Completion of fault code display on check engine lamp.this is end of message code.

CODE 62 Unsuccessful attempt to update EMR mileage in the controller EEPROM.

CODE 63** Controller failure.EEPROM write denied.Check the PCM

Dec 12, 2012 | 1995 Dodge Stratus

2 Answers

What causes a p 0327 diagnostic code on a 95 contour


P0327 - Knock Sensor 1 Circuit Low Input Bank 1 or Single Sensor
First check the knock sensor connector. If the connector is clean and secure, replacing the knock sensor usually takes care of the problem.

- An excessively low voltage from the sensor is sent to Powertrain Control Module (ECM) or Engine Control Module (ECM)

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power

Possible causes
- Knock sensor circuit short to GND.
- Knock sensor circuit short to PWR.
- Knock sensor circuit open.
- Damaged knock sensor.
- Faulty Powertrain Control Module (PCM) or Engine Control Module (ECM).


Test and check it. Hope helps.

May 12, 2011 | 1995 Ford Contour

1 Answer

Where could I find a list of Fault Codes for my 3.3 Litre Voyager?


CHRYSLER OBDII DTC

P1101 HCM/PCM Communication Performance

P1103 Turbocharger Waste Gate Actuator Malfunction

P1104 Turbocharger Waste Gate Solenoid Malfunction

P1105 Fuel Pressure Solenoid Malfunction

P1195 Slow Switching O2 Sensor Bank One Sensor One During catalyst monitoring

P1196 Slow Switching O2 Sensor Bank two Sensor one During catalyst monitoring

P1197 Slow Switching O2 Sensor Bank One Sensor two During catalyst monitoring

P1198 Radiator Temperature Sensor Input voltage too high

P1199 Radiator Temperature Sensor Input voltage too low

P1281 Engine is cold too long

P1282 Fuel Pump Relay control circuit

P1283 Idle select signal invalid

P1284 Fuel Injection pump battery voltage sensor out of range

P1285 Fuel Injection pump controller always on

P1286 Accelerator Position Sensor (APPS) supply voltage too high

P1287 Fuel Injection pump Controller Supply voltage low

P1288 Intake manifold short runner tuning valve solenoid circuit

P1289 Manifold tune valve solenoid circuit

P1290 CNG Fuel system pressure too high

P1291 No Temp rise seen from intake heaters

P1292 CNG Pressure sensor voltage too high

P1293 CNG Pressure sensor voltage too low

P1294 Target idle not reached

P1295 No 5 volts to TP sensor

P1296 No 5 volts to MAP sensor

P1297 No change in MAP sensor from start to run

P1298 lean operation at wide open throttle

P1299 Vacuum Leak detected (IAC fully seated)

P1300 Ignition timing adjustment circuit failure

P1388 Auto shutdown relay control circuit

P1389 No ASD relay output voltage at PCM

P1390 Timing belt skipped one tooth or more

P1391 Intermittent loss of CMP or CKP

P1398 Mis-Fire Adaptive Numerator at Limit (PCM is unable to learn the crank sensors signal

for use in preparation for misfire diagnostics

P1399 Wait to start lamp circuit

P1403 No 5 volt feed to EGR

P1475 Auxiliary 5 volt supply is too high

P1476 Too little secondary air

P1477 Too much secondary air

P1478 Battery Temp Sensor Volts out of limit

P1479 Transmission Fan Relay Circuit

P1480 PCV Solenoid Circuit

P1481 EATX (Electronic Automatic Transaxle) RPM pulse generator performance

P1482 Catalyst Temperature Sensor Circuit shorted low

P1483 Catalyst Temperature Sensor Circuit shorted high

P1484 Catalytic Converter overheat detected

P1485 Air injection solenoid circuit

P1486 EVAP Leak Monitor found a pinched hose

P1487 Hi Speed Fan #2 Circuit

P1488 Auxiliary 5 volt supply output is too low

P1489 High speed fan control relay circuit

P1490 Low speed fan control relay circuit

P1491 Radiator fan relay control circuit

P1492 Ambient/ Battery Temp sensor input voltage too high

P1493 Ambient/ Battery Temp sensor input voltage too low

P1494 Leak detection pump pressure switch or mechanical fault

P1495 Leak detection pump solenoid circuit

P1496 5 volt supply, output too low

P1498 High speed radiator fan ground control relay circuit

P1500 General alternator 'FR' Terminal circuit fault

P1594 Charging system voltage too high

P1595 Speed control solenoid circuits

P1596 Speed control switch always high

P1597 Speed control switch always low

P1598 A/C pressure sensor input voltage too high

P1599 A/C pressure sensor input voltage too low

P1680 Clutch released switch circuit

P1681 No I/P Cluster CCD/ J1850 messages received

P1682 Charging system voltage too low

P1683 Speed control servo power control circuit

P1684 The battery has been disconnected within the last 50 starts

P1685 The SKIM (Smart Key Immobilizer Module) has received an invalid key

P1686 No SKIM (Smart Key Immobilizer Module) bus message received

P1687 No Mechanical Instrument cluster bus message

P1688 Internal Fuel injection pump controller failure

P1689 No communication between the ECM and injection pump module

P1690 Fuel injection pump CKP sensor does not agree with the ECM CKP sensor

P1691 Fuel injection pump controller calibration error

P1692 Fault in companion Engine control module

P1693 A companion DTC was set in both the ECM and PCM

P1694 No CCD message from PCM- Aisin transmission

P1695 No CCD message from body control module

P1696 PCM failure EEPROM write denied

P1697 PCM Failure SRI (Service Reminder Indicator) mileage not stored

P1698 No CCD message from TCM

P1719 Skip shift solenoid circuit

P1740 TCC solenoid or overdrive solenoid performance

P1756 Governor pressure not equal to target at 15-20 psi

P1757 Governor pressure is above 3 PSI when 0 PSI is requested

P1762 Governor pressure sensor offset improper voltage

P1763 Governor pressure sensor voltage to high

P1764 Governor pressure sensor voltage to low
P1765 Transmission 12 volt supply relay control circuit

Oct 03, 2010 | 1998 Plymouth Voyager

1 Answer

What is the 1987 pontiac fiero gt v6 check engine light code list?


CODE 12- NO DISTRIBUTOR REFERENCE PULSES ECM. CODE 13- OXYGEN CIRCUIT. CODE 14- COOLANT SENSOR HIGH TEMP CODE 15- COOLANT SENSOR LOW TEMP. CODE 21 - THROTTLE POSITION SENSOR VOLTAGE HIGH.CODE 22 - THROTTLE POSITION SENSOR VOLTAGE LOW.CODE - 23 MIXTURE CONTROL SOLENOID.FOR CARBURETOR ENGINE. CODE 24 -VECHICLE SPEED SENSOR. CODE 32 - BARO CIRCUIT LOW.CODE 32 - FUEL INJECTED EGR VALVE VACUUM SWITCH SHORTED TO GROUND.OR EGR VALVE SOLENOID CIRCUIT OPEN. CODE 33 - MAP SENSOR.CODE 34 - VACUUM SENSOR OR MAP SENSOR.CODE 35 - IDLE SPEED CONTROL. CODE 41 - EST CIRCUIT. CODE 42 - ELECTRONIC SPARK TIMING.CODE 43 - ELECTRONIC SPARK CONTROL UNIT. CODE 44 - LEAN EXHAUST.CODE 45 - RICH EXHAUST. CODE 51 - PROM OR MEM CAL.CODE 52 - CALPAK. CODE 53 -EGR VALVE CARBURETED ENGINE THE EGR VALVE VACUUM SENSOR HAS RECEIVED IMPROPER EGR VACUUM. CODE 54 - M C SOLENOID CARBURETED ENGINE MIXTURE CONTROL SOLENOID SHORTED OR FAULTY ECM.CODE 54- FUEL INJECTED ENGINE FUEL PUMP VOLTAGE IS LOW.CODE 55 - ECM MAKE SURE PCM GROUND CONNECTIONS ARE TIGHT.IF OKAY.REPLACE THE ECM.

Mar 27, 2010 | 1987 Pontiac Fiero

1 Answer

WHY IS THE SERVICE ENGINE LIGHT ON IN MY SATURN??


The Check Engine light will light when the ECU stores a trouble code.
Counting the Flashes
To retrieve trouble codes, turn the ignition key to the "on" position with the engine OFF.
The Check engine light will flash many short blinks. The total number of blinks equals the code number. For example, flash,pause, flash,flash = code 12.If more than one code is stored, the Check engine light will flash the codes in sequence (lowest to highest) with a pause between each code. The codes will repeat until the key is turned to the OFF position.

11 Transaxle codes present 12 Diagnostic check only 13 Oxygen sensor circuit 14 Coolant sensor/high temperature 15 Coolant sensor/low temperature 17 PCM fault - pull-up resistor 19 6X signal fault (92-95 models) 21 Throttle position sensor-voltage high 22 Throttle position sensor-voltage low 23 IAT circuit low 24 VSS circuit-no signal 25 IAT circuit-Temp out of high range 26 Quad driver output fault 32 EGR system fault 33 MAP sensor - voltage out of range high 34 MAP sensor - voltage out of range low 35 IAC - rpm out of range 41 Ignition control circuit-open or shorted 42 Bypass circuit - shorted or open 41/42 IC control circuit grounded/bypass open 43 Knock sensor circuit shorted or open 44 O2 sensor indicates lean condition 45 O2 sensor indicates rich condition 46 Power steeringpressure circit(91 models)open or shorted 49 High idle indicates vacuum leak 51 PCM memory error 53 System voltage error 55 A/D error 58 trans fluid temperature too high 59 Trans fluid temperature too low 66/67 A/C pressure sensor 81 ABS message fault 82 PCM internal communication fault

Mar 10, 2010 | 1992 Saturn SL2

1 Answer

I need all the engine diagnostic codes for a 94 plymouth sundance


11 Timing belt2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

Jul 08, 2009 | 1994 Plymouth Sundance

1 Answer

My 1995 neon has ~105K miles, just passed emmissions with flying colors 1 week ago, and the ''check engine light'' came on. I have checked oil, coolant, brake juice, fan belt and air conditioner belt. Car...


the light has nothing to do with oil or coolant levels. it comes on for one of the following reasons. You will need to have the system computer memory tested to see which fault the system has.
CODE Description of Trouble Code
11 Timing belt skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failure

Jun 11, 2009 | 1995 Dodge Neon

1 Answer

Error codes, oil pressure sensor and engine control moduale


Hello, It should actually be an oil sending unit, and is located on the back of the intake manifold to the left of the distributor. *The P0523 is Oil Pressure Sending Unit Voltage too high *P1693 Generic fault indicating a fault in the bus or PCM/ECM interface *P1682 - I can't find this code Anyways, I will post here all the error codes for future reference. Dodge Cummins Check Engine Error Codes Cycle Key on-off-on-off-on to read codes in odometer display P0002 ECM fuel calibration error P0016 Crankshaft/Camshaft Timing Misalignment/Out-of- Sync P0071 Ambient Temperature Sensor Performance / Rationality P0072 Ambient Temperature Sensor Low P0073 Ambient Temperature Sensor High P0088 Fuel Rail Pressure Too High P0106 Manifold Absolute Pressure Sensor Performance / Rationality P0107 Manifold Absolute Pressure Sensor Low P0108 Manifold Absolute Pressure Sensor High P0111 Intake Air / Charge Temperature Sensor Performance / Rationality P0112 Intake Air / Charge Temperature Sensor Low P0113 Intake Air / Charge Temperature Sensor High P0116 Engine Coolant Temperature Sensor Performance / Rationality P0117 Engine Coolant Temperature Sensor Low P0118 Engine Coolant Temperature Sensor High P0121 Accelerator Position Sensor (APPS) Signal Voltage Too Low P0122 Accelerator Position Sensor (APPS) LowAPPS Voltage Input Too Low P0123 Accelerator Position Sensor (APPS) Signal Voltage Too High P0128 Cooling System Error / Thermostat Rationality P0148 Fuel Delivery Error P0168 Fuel Temp Too High P0169 Water-in-Fuel Detected For Too Long P0192 Fuel Rail Pressure Sensor Low P0193 Fuel Rail Pressure Sensor High P0201 Fuel Injector 1 Circuit P0202 Fuel Injector 2 Circuit P0203 Fuel Injector 3 Circuit P0204 Fuel Injector 4 Circuit P0205 Fuel Injector 5 Circuit P0206 Fuel Injector 6 Circuit P0216 Fuel Injection pump Timing Malfunciton [new injector pump time] P0217 Coolant Temperature Too High P0219 Engine Overspeed P0230 Transfer pump circuit out of range P0234 Turbocharger Overboost Condition P0235 Turbocharger Boost Sensor A Circuit P0236 Turbocharger Boost Pressure Sensor Performance / Rationality P0237 Turbocharger Boost Pressure Sensor Low P0238 Turbocharger Boost Pressure Sensor High P0251 Fuel Injection Pump Mechanical Failure Fuel Valve Feedback Circuit P0252 Injection Pump Fuel Metering Control "A" Range/Performance P0253 Fuel Injection Pump Fuel Valve Open Circuit P0254 Fuel Injection Pump Fuel Valve Current Too High P0300 Multiple Cylinder Misfire P0301 Cylinder 1 Misfire P0302 Cylinder 2 Misfire P0303 Cylinder 3 Misfire P0304 Cylinder 4 Misfire P0305 Cylinder 5 Misfire P0306 Cylinder 6 Misfire P0335 Crankshaft Position Sensor Circuit P0336 Crankshaft Position Sensor Performance P0337 Crankshaft Position Sensor Circuit Low P0338 Crankshaft Position Sensor Circuit High P0340 Camshaft Position Sensor Circuit P0341 Camshaft Position Sensor Performance / Rationality P0370 Timing Reference High Resolution Signal "A" P0380 Intake Air Heater #1 Control circuit P0381 Wait-to-Start Lamp Inoperative P0382 Intake Air Heater #2 Control circuit P0460 Fuel Level Sensor A Circuit P0461 Fuel Level Sensor 1 Performance / Rationality P0462 Fuel Level Sensor 1 Low P0463 Fuel Level Sensor 1 High P0477 Exhaust Pressure Control Relay Low P0478 Exhaust Pressure Control Relay High P0480 Cooling Fan 1 Control Circuit/Open (Low Speed Fan Relay) P0483 Cooling Fan Speed P0500 Vehicle Speed Sensor 1 Circuit, or No Vehicle Speed Reference Signal 1 P0514 Battery Temperature Sensor Performance / Rationality P0516 Battery Temperature Sensor Low P0517 Battery Temperature Sensor High P0521 Oil Pressure Sensor Performance / Rationality P0522 Engine Oil Pressure Sensor/Switch Circuit Low Input P0523 Oil Pressure Sending Unit Voltage too high P0524 Oil Pressure Too Low P0532 A/C Pressure Sensor Low P0533 A/C Pressure Sensor High P0541 Intake Air Heater Relay 1 Low P0542 Intake Air Heater Relay 1 High P0562 Battery Voltage Low P0563 Battery Voltage High P0572 Brake Switch 1 Low P0573 Brake Switch 1 High P0576 Cruise Control Input Circuit Low P0580 Speed Control Multiplexed Switch 1 Low P0581 Speed Control Multiplexed Switch 1 High P0602 Control Module Programming Error/NotProgrammed P0604 Internal Control Module RAM Integrity Failure P0606 Internal ECM Processor P0607 ECU Internal Performance P0622 Generator Field Control Circuit P0628 Fuel Pump Relay Circuit Low, or Fuel Lift Pump Control Circuit Low P0629 Fuel Pump Relay Circuit High, or Fuel Lift Pump Control Circuit High P0630 VIN Not Programmed in PCM P0633 SKIM Key Not Programmed in PCM P0642 Sensor Reference Voltage 1 Circuit Low P0643 Sensor Reference Voltage 1 Circuit High P0646 A/C Clutch Relay Circuit Low P0647 A/C Clutch Relay Circuit High P0652 Sensor Reference Voltage 2 Circuit Low P0653 Sensor Reference Voltage 2 Circuit High P0698 Sensor Reference Voltage 3 Circuit Low P0699 Sensor Reference Voltage 3 Circuit High P0700 Transmission Control System (MIL Request) P0743 Torque Converter Clutch Circuit Electrical P0753 Shift Solenoid "A" Electrical P0837 Four Wheel Drive (4WD) Switch Performance / Rationality P0838 Four Wheel Drive (4WD) Switch Circuit Low P0839 Four Wheel Drive (4WD) Switch Circuit High P1488 Auxiliary 5 volt supply output is too low P1492 Ambient/batt temp sensor volts too high P1493 Ambient/batt temp sensor volts too low P1596 Speed Control Switch always high P1597 Speed Control Switch always low P1652 J1850 Communication Bus P1687 No Cluster BUS Message or No Messages from the Mechanical Instrument Cluster P1688 Internal Fuel Injection Pump Controller Failure P1689 No Communication Between ECM & Injection Pump Module P1690 Fuel injection pump CKP Sensor Does Not Agree With ECM CKP Sensor P1691 Fuel Injection Pump Controller Calibration Failure P1693 Generic fault indicating a fault in the bus or PCM/ECM interface P1757 Governor pressure is above 3 PSI when 0 PSI is requested P1762 Governor Press Sensor Offset Volts Too Low or Too High P1765 Transmission 12 volt supply relay control circuit P2121 Pedal Position Sensor 1 Performance / Rationality P2122 Pedal Position Sensor 1 Low P2123 Pedal Position Sensor 1 High P2127 Pedal Validation Switch 2 Low P2128 Pedal Validation Switch 2 High P2146 Fuel Injector Group 1 Supply Voltage Circuit P2149 Fuel Injector Group 2 Supply Voltage Circuit P2266 Water in Fuel Sensor Circuit Low P2269 Water in Fuel Condition P2502 Charging System Output Voltage P2503 Charging System Output Low P2504 Charging System Output High P2509 ECM/PCM Power Input Signal Intermittent P2607 Intake Air Heater Relay 2 Low P2608 Intake Air Heater Relay 2 High P2609 Intake Air Heater System Performance Hope this will help you. Cheers! Ryan

Jun 11, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
1997 Dodge Intrepid Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...