Question about Cars & Trucks
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the cover just pulls off and disconnect breather hose as u lift it.there is about 15 screws to remove then the cover opens
Posted on Jul 12, 2009
Remove plastic plug on the inside of door there is 10 mm hole use a hooked pick set pick put through the hole and pull the plastic cir clip towards the back of the door that will release the smaller part of the outer handle then the handle itself can be taken out.this is so simple but so deceiving the actual cir clip is hard to notice because of all the plastic **** on the inside backing plate the cir clip is just on the inside of hole look hard it is 2mm thick & 20mm high (black plastic) place point of pick in between backing plate & cir clip hook it and pull back the front door is based on the same principle but is a lot easier
Posted on Jul 16, 2009
SOURCE: Removing VW polo 2005 battery?
Removing a battery from a Beetle is a bit complex and tricky. I just changed the battery in a 2003 2.0 Beetle. However, the process is very similar in a TDI Beetle. You will need more than your standard generic tool set in order to complete this task. Your tool list needs to consist of a pair of pliers (prefer locking type), a # 20 TORX head screwdriver (You will also need this if you ever plan on changing the Beetle's internal dash pollen filter for the A/C. ), a 10 mm and 13 mm sockets, a long extension and a wobble or universal to allow flexibility in tight spaces, an allen socket for removing the power steering reservoir, and a small adjustable wrench or a 10mm to remove the battery cables. If you are changing the battery you might as well buy a new Air filter since you will need to remove the air box in order to replace the battery. If you do change the air filter you will need a phillips head screwdriver.
1. Pop the hood.
2. Remove the two 10 mm bolts that hold down the air filter box.
3. Undo the clamp that holds the large tubing to the air box using your pliers. Move the tubing away from the box.
4. Unclip hose attached to the back of the air box near the large hose (under it).
5. remove the small breather hose from the air box.
6. Pull air box up and out.
7. Remove snap on cover from top of battery.
8. Remove small snap on wiring cover from back of the battery covering.
9. Unbolt power steering reservoir (next to battery case).
10. Disconnect the battery cables. Positive side first.
11. Remove the 13 mm bolt at the base of the battery along with the hold down clamp.
12. Pull the top wiring away from the battery case and then slide the battery towards the engine.
13. Remove the plastic battery case.
14. Remove the battery
Posted on Oct 07, 2009
has to remove the inside panel door and remove the clip inside to open the handle cover then u can see the two nuts and remove them
Posted on Mar 28, 2010
Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing
Posted on Sep 12, 2010
Tips for a great answer:
Feb 01, 2015 | 2010 Mazda CX-7
Feb 01, 2015 | 2010 Mazda CX-7
Oct 20, 2014 | Cars & Trucks
Dec 06, 2013 | 1999 Volkswagen New Jetta
Mar 18, 2013 | Volkswagen Polo Cars & Trucks
Sep 20, 2011 | 2009 Volkswagen Tiguan
Jan 30, 2010 | 2003 Volkswagen Golf
Jun 15, 2009 | 1999 Volkswagen Golf
Apr 22, 2009 | 2001 Volkswagen Golf
May 24, 2018 | Cars & Trucks
1,282 people viewed this question
Usually answered in minutes!