Question about 1996 Mazda Protege

1 Answer

The heat in my 96 mazda protege dosn't work

The blower motor does work but isnt getting power and i just replaced the fuse

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Mazda Master
  • 2,620 Answers

With the ignition and fan switches turned on check for power at fan motor.If you have power at the motor then wiggle and maybe pull on the blower motor resistor and if fan comes on just fix the connection.But when you check for power at the blower motor and don't have power then check the fan relay if it does'nt click when you turn it on then its faulty.

Posted on Oct 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Blown main fuse on 2003 mazda protege 5.

There are two bolts on the side of the fuse itself. Under the fuse box on each side. Unbolt those and it will come out.

Posted on Dec 23, 2008

  • 423 Answers

SOURCE: Replacing 2 belts on a 2000 Mazda Protege

I recommend that you go to any Auto Parts store and by a repair user manual for your 2000 Mazda Protege.  They have pictures and arrows and stuff that you will need to do the whole job.  The non-Mazda version will cost approximately $15.00.
Because of the tensioner that may come off when while you are doing these belt changes, it is too complicated to talk you through this.
But with the manual, I am confident you can change them.

Posted on Apr 16, 2009

  • 131 Answers

SOURCE: How to replace knock senor switch on 2002 mazda protege 5


Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

Posted on May 10, 2009

  • 1 Answer

SOURCE: Fan blower doesn't work

I have the same truck. Mine only worked on high. I replaced the blower motor resistor and it worked for a few seconds and then the resistor started to overheat and fry. I then removed the blower motor and found it to be pretty seized up so I replaced it along with another resistor and it works great. At any rate, be careful not to ruin a new resistor. If it shows any signs of getting hot when you first fire it up then turn off the blower motor immediately and replace it too. In my case, the worn out blower motor is probably what caused the original resistor and the replacement to fail in the first place.

Posted on Jun 30, 2009

  • 2 Answers

SOURCE: where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Blower motor not working on 4 1998 Mazda protege


check for power and ground at the blower motor. if this is good then hit motor. if it starts the motor needs replacing. then check the fuse then the fan speed switch for power and ground going to the switch and coming out of switch.

Jul 28, 2015 | 1998 Mazda Protege

1 Answer

Fan fuse blown?


I assume you have replaced the blower fuse before.
The compressor has probably failed and that is what is blowing the fuse. You may be able to unplug the clutch on the compressor and use the heat without blowing the fuse again.
Otherwise someone will have to trace the circuit with the blown fuse to find out what it powers.

Dec 19, 2012 | 1997 Mazda Protege

1 Answer

My 1997 Mazda Protege heater does not blow air, i replaced and tested blower motor, resistor and fuses inside the cab. Still nothing


Before replacing the blower motor, you should have checked the motor's input wiring loom for power.
Do you have power here?

If you don't have power, then you need to check your blower switch output wires.

Nov 04, 2012 | 1997 Mazda Protege

1 Answer

Is there a blower motor relay or fuse on a 1995 Mazda Protege lx?


That fuse sounds like it powers the ac compressor.
The blower motor usually takes a 30 amp fuse.
Does the blower motor work if you hook it to direct voltage ?

Jul 04, 2012 | Cars & Trucks

2 Answers

I have a 2002 protege a/c wont work on all blower speeds and my friends 2000 blower will only work on 2 settings


Replace fan switch in dash.Or may even just need connections cleaned with some wd/40. To replace switch you need to remove dash and knob's, Then you have a switch that has the wires from fan to connector. . If these are ok and clean you need to replace your blower motor, Best of luck to you.
.

Apr 04, 2011 | 2003 Mazda Protege

1 Answer

The blower motor for the heat doesnt work


Replace the resistor or the blower motor.

Dec 28, 2010 | 2000 Mazda Protege

1 Answer

No heat. The heather rad is ok. No circulation throught the heather rad


check blower motor fuse if it isnt the fuse maybe a bad blower motor do you also have no air flow when you turn ac on the radiator on the front of the car is no your heater core heater core sits inside your duck work for your air vents has this just started happing or did you buy the car this way

Nov 29, 2010 | 1995 Mazda Protege

1 Answer

What could be the problem with a1997 mazde protege when the A/C and deforst fan dose not work


check fuses ,switchs and relays first thenthe blower motor. chances are its the blower motor

Jul 11, 2010 | 1997 Mazda Protege

1 Answer

96 Mazda Protege is dead and has no power, wont turn over!


check all your fuses sometime when giving a jump start
a surge of power a cures and blows out the main fuse

Nov 14, 2009 | 1996 Mazda Protege

2 Answers

Fan blower fuse location on a ford f150 year 2000


FUSE #105 40A** Climate Control Front Blower, THIS FUSE IS LOCATED IN THE UNDERHOOD POWER DISTRIBUTIOPN BOX

Oct 14, 2009 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
1996 Mazda Protege Logo

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...