Question about 1993 Jeep Cherokee Country

1 Answer

I own a 93 jeep grand cherokee and the brake lights seem to always be on as if they are pressed... but only when the lights are turned on does this happen. also the turn signals stopped working comple

The brakes seem to not work but light up at their brightest when the lights are turned on. also the turn signals stopped working altogether

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

The muti frunction switch has to be replaced.

Posted on Oct 28, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: turn signal

try a flasher

Posted on Sep 19, 2008

  • 1 Answer

SOURCE: the tail lights are out, so the brake lights-Jeep Grand Cherokee

i have a 2002 jeep grand cherokee i had the same problem when i would apply my brakes when the headlights were on my brake lights would go out, i found that my bulbsocket was not making good contact with the socket housing, if you notice when you take off a bulb, look at the light fixture where you unscrewed your breaklight bulb you will notice 3 medal contacts-they should be silver in the socket housing and like a copper on the socket bulb, in the socket housing their should be 2 silver contacts together and 1 by itself the one that looks by itself is making bad contact with the copper one thats by itself on the bulb, what you can do for a quick fix is; get a small piece of low cage wire or a thin piece of metal like copper stick that in to the bottom or top of that metal contact--i did it through the bottom leave the wire or piece of medal sticking out enough for where it can get contact with the bulb (just a little wire is enough to make contact, now screw the bulb on and test it---it will work----i did it to mine, if you need more assistance let me know lmadrid82@yahoo.com

Posted on Feb 20, 2009

wikkidd420
  • 96 Answers

SOURCE: 1995 Jeep Grand Cherokee Limited - flasher relay location

More than likely you have a bad ground. Under the rear of the vehicle, behind the rear bumper there will be a few wires running to a bolt in the frame (left side i think) Check that no wires are loose or boken. Also if you have a trailer wiring harness, check to see if it has not been damaged. Let me know if this helps :)

Posted on Apr 30, 2009

  • 17 Answers

SOURCE: turn signals on my 2004 jeep don't work what to

If one of your bulbs has blown you will get a faster relay click when you activate the indicators. It sounds as though the relay itself could be sticking / broken.

Of course it could just be a blown fuse, I would check that first before changing relays

Posted on Nov 12, 2009

  • 398 Answers

SOURCE: How to install a brake light switch on a Grand Jeep Cherokee

Dont do it... It will take you bout 30 minutes to remove and replace it on the steering column

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 93 Jeep cherokee brake lights don't work


Check the Brake peddle switch, or the turn signal switch ( all the lights go through the turn sig switch ) Or check the brake light fuse. Make sure the lights are not burned out by chance also.

Sep 29, 2012 | Cars & Trucks

1 Answer

My 93 jeep grand cherokee is not getting fuel...if I disconnect the negative post for awhile and then reconnect it, the jeep gets fuel and will run....what is going on?


If the check engine light does not light up on the dash when you turn on the ignition, at those times when your jeep doesn't want to start, then your main jeep ecm is in need of repair. The fuel pump relay will get energized only after that check engine light comes on. It's a known problem, especially with the first and second year production Grand Cherokees, 93 and 94.

Jun 30, 2012 | 1993 Jeep Grand Cherokee

1 Answer

My brake lights will not turn off when the motor is off what is wrong?


Well, the brake light circuit is always energized. If you have the vehicle off and press on the brakes, the lights should illuminate.

If the brake lights remain on without the pedal being pressed, something is wrong with the switch, located under the dash, along the pedal arm. This switch may need adjustment or replacement.

Dec 11, 2010 | 1996 Jeep Grand Cherokee

1 Answer

All of the lights work on my 93 Jeep Cherokee 6 cyl except the taillights. Can't seem to find a fuse out and I've replaced bulbs which I've tested and know they work.


There is a plug under the dash, directly under the steering column, that sometimes gets unplugged accidently. From what I remember, it's white. Check to see if any of them white plugs directly under there are slightly unplugged. Happened on my 93 grand cherokee once and I almost got rear ended from having no brake lights.

Oct 24, 2010 | 1993 Jeep Grand Cherokee

1 Answer

How to change a heater core in a 93 jeep grand cherokee


When I turn my heater on, after my 1993 Jeep Grand Cherokee has warmed up, there is a dusty, watery smell for a few minutes, then it goes away. Also, it doesn't put out as much heat as I think it should. I don't think the heater core has a leak, because I always seem to have the same amount of coolant in the radiator and the heater core is not leaking on the inside of the truck.

Jan 26, 2010 | 1993 Jeep Grand Cherokee

2 Answers

My 2004 jeep grand cherokee's drivers side brake light goes out when i press the brakes with the head lights on but it. it works normal when the head lights are not on. any suggestions


I would suggest that you take a look here (I used this to correct brake-light issues on my '01):

http://www.topix.com/forum/autos/jeep-grand-cherokee/T63DRCOTUFKMHQ207

Many Grand Cherokees have had this type of issue. The thread is lengthy, but does cover just about every type of issue known with the tail/brake lights.

Dec 07, 2009 | 2004 Jeep Grand Cherokee

2 Answers

When lights are on and brake pedals are pressed all brake lights go off except for top brake light on 99 jeep grand cherokee laredo...


i take it the brake lights work ok when the lights are not on??? check the ground going to the lights

Jan 04, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Jeep seems to slip into neutral when the brake is on


the throttle position sensor can cause this also.

Dec 11, 2008 | 2004 Jeep Grand Cherokee

1 Answer

1997 jeep grand cherokee laredo cannot turn off exterior lights


maybe the brake pedal is not returning all the way to top position when pressed.

Dec 06, 2008 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
1993 Jeep Cherokee Country Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...