Question about 2008 Chrysler Sebring Convertible

Open Question

Need plastic hinges for the two piece cargo shield,there broke , we're can I get them

Its a 2009 Sebring con. Touring. Any suggestions.?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: connvertible top malfunction chrysler sebring2008/set cargo shield door signal

Open the trunk & reposition the folding cargo shield tray the top sits in when it is down. There is a small switch in the tray's mounting notch that indicates when the tray is in place to recieve the lowered top.

Posted on Aug 26, 2012

Ad
  • 1986 Answers

SOURCE: Adjust the headlights on 2005 Sebring, Touring Sedan

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall. Also mark where the center of the bulbs would be (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall. For horizontal, aim the hot spot directly at the line you marked for the center of your bulbs

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

  • 236 Answers

SOURCE: Coolant Resevoir Tank Leak

A repair might buy a little time but you should replace.Either the junk yard or dealer will have this part.it is a coolant resevoir.

Posted on Aug 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of starter relay for a 2010 4 cylender touring sebring


The starter relay is called the starter solenoid and is located on the starter motor.

Sep 08, 2016 | 2010 Chrysler Sebring Touring

2 Answers

How do I change an oil pressure sender on a 2005 Chrysler Sebring Touring 2.7


on the back of engin fierwall side green conecter on engin block

Feb 25, 2014 | 2005 Chrysler Sebring Sedan

1 Answer

Owners manual


It could just be engine cover. My guess.

Jul 12, 2013 | 2006 Chrysler Sebring

1 Answer

Coolant Resevoir Tank Leak


A repair might buy a little time but you should replace.Either the junk yard or dealer will have this part.it is a coolant resevoir.

Aug 28, 2012 | 2002 Chrysler Sebring

1 Answer

Connvertible top malfunction chrysler sebring2008/set cargo shield door signal


Open the trunk & reposition the folding cargo shield tray the top sits in when it is down. There is a small switch in the tray's mounting notch that indicates when the tray is in place to recieve the lowered top.

Aug 25, 2012 | 2008 Chrysler Sebring

1 Answer

I have a 2008 sebring...top lifts up but will not go down. Top seems off track to me. Dealer said it needs a "bow kit" which looked like 2 metal brackets. said they were bent. any suggestions???


The mechanic is right. check hinges for bends.some people lift it up or put it down while moving,and that jacks the motor and hinges up. are you one of those people???

Apr 28, 2010 | 2008 Chrysler Sebring Convertible

1 Answer

How do I replace the cabin air filter on a 1997 mercury sable?


It is underneath the black plastic pieces under/below the wipers. There are just a few round fasteners that hold down the passenger side piece that need to be removed to access the filter.
You have to remove the windshield wiper arms, then take off the plastic molding that lies between your windshield. Once that is off (it comes out in two pieces) on the passenger side of the car, under the windshield just behind the firewall there is a plastic rain shield with two screws. Remove the rain shield. The cabin filter is under that rain shield. FYI...every bolt is metric, and be careful when removing the plastic molding-only turn those screws a half turn, they break very easily!

Jun 25, 2009 | 1997 Mercury Sable

1 Answer

Headlight piece


I would suggest going to a junkyard -- that's the best place to get pieces of assemblies without paying a fortune.

Apr 30, 2009 | 2000 Audi TT

1 Answer

Chrysler Sebring 2002 convertible door assembly


use a scraper and remove the water shield as its called, very slowly . make sure to try and keep as much of the sealer on the water shield as possible. if you want to completely remove it you also have to disconnect all the wires leading to the door panel

Jul 07, 2008 | 2002 Chrysler Sebring

Not finding what you are looking for?
2008 Chrysler Sebring Convertible Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...