Question about 2005 Dodge Ram 1500

Open Question

Location of the cam shaft sensor on a 2005 dodge ram 1500 4.7l

Checked code on 2005, dodge ram 1500 and the code i got was po344 which us a cam shaft sensor have a 4.7l need to know were it is located

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: location of dodge neon 2005 oxygen sensor

ask at the parts store where i bought the part

Posted on Jun 08, 2008

Ad
  • 3 Answers

SOURCE: Cam Shaft Sensor Problems

Had the same problem before on my 04 Neon SXT...camshaft sensor is on left side of engine block, take out the battery and to the left of it (face car) is the camshaft position sensor. To change it you'll have to move a few hoses but its plan to see there on the left side of the engine...pretty easy remove and replace. Fixed my problem of car not going above 2k RPM when i replaced the sensor.

Posted on Dec 29, 2008

66 chrgr
  • 1011 Answers

SOURCE: P0406 Code on '05 Dodge Ram Hemi 5.7

this is a egr problem lack off flow

Posted on Jan 25, 2009

  • 19 Answers

SOURCE: 2005 dodge noen cam sensor

I own a 2002 neon sxt and recently had to replace the cam sensor it should be in the same place.
look on the right side of the motor you should see it. it'll have a small wire harness that clips in the top and its fastend with 4 bolts. Oh and take the battery out before you do it it makes it a lot easier.

Hope this helps.

Posted on Feb 25, 2009

emissionwiz
  • 76848 Answers

SOURCE: knock sensor dont work for 2005 dodge durango

this problem is very seldom the knock sensor, it can be the harness connector at the sensor or the engine has excessive knock which will set a code, u did not mention the particular code so hard to say, the location of the knock sensor is the lower section of the engine block, it is screwed into what would normally be a block drain plug, if u replace it u need to torque it to whatever the factory spec is or it can cause it throw another code..

Posted on May 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 dodge started then died. now will not fire light indicates ETC. How can I troublehoot it?


ETC is electronic traction control. However I feel that the problem is more likely cam/crank position sensor related Check that the cam shaft is turning (broken timing belt/chain). Check for fuel pressure/injector faults. Check for HT spark to plugs. Run fault codes to determine the fault.

Jun 14, 2014 | Dodge Pickup Cars & Trucks

2 Answers

Eng starts hard,runs good until the rpm is over 2200 then it stumbles my input voltage on the cam sensor is 5volts ,on most cars i've read should have 8volts where


Both crank and cam sensors have a 8 volt reference I have found the wiring melted together where it cross over transmission shorting out the signal. also test your reference voltage at the computer with circuit unplugged at sensor watch meter and wiggle wiring going back to computer this will help find faulty area.

Nov 07, 2013 | 2005 Chrysler Sebring Conv

1 Answer

2004 dodge stratus 2.4 dohc po344 code


PO 340 thru PO344 are cam shaft position sensor issues

That does not tell you what is wrong or to replace anything

Have it diagnosed at a repair shop

A sensor could fail & it more than likely is just
reporting other issues you have to have resolved.

Oct 02, 2012 | 2004 Dodge Stratus

1 Answer

What does PO344 mean


Code PO344: Rationality error detected for intermittent loss of camshaft position sensor circuit

A problem with either your cam/camshaft sensor.

Apr 30, 2012 | 2006 Dodge Durango

1 Answer

Check Engine Light Code PO344


Cam sensor closed circuit. Does the car run poorly or get mad fuel economy? I would suggest getting both the cam and the crank sensors replaced at the same time as they usually go bad consecutively.

May 03, 2010 | 2003 Dodge Neon

3 Answers

How can i fix code po344 intrepid 2002


Before replacing the cam shaft sensor,verify good terminal tension and connection at the sensor.This carline has a history of faulty connections here and this could fixya before spending the cash on car parts....good luck

Jul 24, 2009 | 2004 Dodge Intrepid

1 Answer

I'm getting the engine light coming every so often. It seems that after I fill the tank and get down around 3/4 tank, The message I'm getting is "EVAP Emission Control System Purge Flow Fault". PO441 and...


I have a 2004 dodge stratus 2.4 dual overhead cam. When driving down the road, bell goes off, check engine light comes on, and it's like I'm driving on limp mode, when going over 2000 rpm's, there's a severe stutter. After getting code for light it points to cam shaft sensor, which i changed. I also changed crank shaft sensor. After all of this was done, drove great for about 30 miles and the same thing happened all over again. If anyone can point me in the right direction it would be greatly appreciated.

Jul 05, 2009 | 2004 Dodge Stratus

1 Answer

Po340 and po344 intrepid


Take a look at this link http://www.obd-codes.com/p0340.  The problem lies in the cam shaft sensor circuit which means that it isn't necessarily the sensor itself.  Read what that page has to say and just start from the top and work your way down the solutions.  As far as how much it cost, it obviously depends on what is wrong, but assuming it is your cam shaft sensor you can buy the part for around forty dollars at AutoZone.  Let me know if you have any other questions.  Thanks for rating my response and for using FixYa!

May 29, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...