Question about 1999 Jeep Grand Cherokee

1 Answer

How do I remove the drivers side head lamp - 1999 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 51 Answers

There should be two 8mm bolts on top of the healdlamp capsule that are visable when the hood is open. unscrew the bolts and pull them out they are about 8in long. once the bolts are removed you are going to need a small prybar or a big flathead screwdriver and you need to carefully pop the head light capsule out of its retaining clips. it will come out hard but be careful not to crack the headlight capsule or the plastic bracket it clips into. once the capsule has been removed you can gain access to change all the bulbs in the unit. some of the white clips may come off with the capsule. you must remove them and snap them back into the plastic bracket from which they came before installing the capsule otherwise you will break the bracket or headlight capsule. dont be afraid to use a little grease on the clips on assembly to ease installation.

Posted on Jan 07, 2009

2 Suggested Answers

reichweinj
  • 71 Answers

SOURCE: Driver's side head light

There is 2 plastic clips behind the headlight, lift these up and pull the headlight out. Then just twist the plastic cap out of the headlight and replace. (Do not touch the bulb when replacing). Then put headlight back in all the way and slide the plastic retainer clips back into position.

Posted on Oct 30, 2008

  • 1 Answer

SOURCE: Drivers side head lamp assy removal

if it is the torx head screw on the bottom, the metal feral might be spinning n plastic housing.

Posted on Feb 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why do all lights work except low beam driver side head lamp?


Seems like if your other low beam is lit, there's something wrong with the new bulb. Make sure it's the exact type needed, and switch the working bulb from the pass. side to drivers side to check.

Feb 22, 2016 | 2010 Nissan Altima

1 Answer

How do you change the low beam headlight on drivers side of suzuki kazahi


You need to remove the front bumper.
It is easy but tricky.
Once the bumper is off you need to remove all the plastic head lamp.
You'll see the light bulbs once you remove a round rubber cover in the back of the plastic head lamp.

Oct 24, 2013 | 2011 Suzuki Kizashi

1 Answer

How do I replace the front left (driver side) headlight? I have removed the cap and the electrical, but can't figure out how to remove the bulb so I can put a new one in. Your help is appreciated.


Removal & Installation
  1. Disconnect the negative battery terminal.

  2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.

  3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
    41311_tucs_g0048.gif

    Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)

  4. To install, reverse removal procedure.

Dec 12, 2010 | 2005 Hyundai Tucson

1 Answer

How to change headlights


this is regarding low beam head lamps. i have a 2006 kia optima and to change the head lamp, there is a cap right behind the head lamp area that screws off. remove the connection to the head lamp. oncece the cap is unscrewed and the connection is removed, you will see a clamp that keeps the lamp bulb in place. save yourself the headache and do not unscrew this clamp as it is aggrivating to screw back into place....on the opposite side of the screw u can push on the clamp ( i think it is downward) and it will swivel one side away from the lamp bulb, just that side, while the screw side keeps the clamp in place. remove the bulb, place your new on into place (there are 3 notches on the metal part of the lamp bulb that sit into place. take a look and u will see how they need to sit.) replace the clamp, replace the connection and screw cap back on and you are finished. the first time took a minute to figure out, but once u do it, it only takes about 5 minutes to do after that first initial time.

Oct 15, 2010 | 2004 Kia Optima

1 Answer

How to change the fog lamp bulb on an audi a6 avant 2003


First remove the driver's side fog lamp plastic cover out from front bumper. After that you will find torx socket head panel screws from fog lamp. See picture below:


4958043.png

Jun 12, 2010 | 2003 Audi A6

1 Answer

How do I replace the Drivers side fog lamp (not just bulb) on my 2002 Audi A4 18T?


First remove the driver's side fog lamp plastic cover out from front bumper. After that you will find torx socket head panel screws from fog lamp. See picture below:

de0b0fe.png

Feb 06, 2010 | 2002 Audi A4

2 Answers

How to replace headlights bulbs in a grand cherokee 2001


  1. Remove the jack screw attaching the top of the head lamp to the head lamp mounting module.
  2. Grasp the upper inboard and lower outboard corners of the head lamp and pull the head lamp outward.
  3. Remove the bad bulb socket from the head lamp module and remove bulb from socket.
  4. Install new bulb into socket and reinstall socket into head lamp module.
  5. Position the head lamp on the vehicle and align the ball studs with the sockets.
  6. Push the head lamp inward to secure the ball studs with the sockets.
  7. Install the jack screw attaching the top of head lamp to the head lamp mounting module.
Do not touch glass of halogen bulbs at the oil can cause the headlight to blow out

Nov 12, 2009 | 2001 Jeep Grand Cherokee

1 Answer

How do you remove the head lamp assembly on a 1993


1. Make sure headlamp is off and open hood.
2. Taurus model years 1990-1999: you must remove the whole headlamp to replace the bulb. Not a horrible task. Just annoying.
3. Facing the driver's side headlamp, and looking at the headlamp itself, at clock positions 8, 11 and 1 are the headlight housing screws. They all look the same. Using a 10mm socket wrench, remove these 3 screws and set them aside.
4. Just to the right of the "11 o'clock" housing screw is a bolt (same hexagonal 10mm sized top as the housing screws). This just needs a few turns to loosen it.
5. Gently pull the whole headlight forward. Now you can get at the bulb.
6. Disconnect the electrical connector from the bulb. Now the headlamp is free to work with. Remove the bulb, replace with a new bulb, make sure the bulb housing cylinder is in place and reconnect the electical.
7. Place headlamp back into position. Line up screw holes. Tighten the bolt. Replace housing screws and tighten.
8. Passenger side headlamp is mirror image of driver's side. Screws at 11, 1 and 4 o'clock positions. Bolt should be to the left of the "1 o'clock" housing screw.

Oct 12, 2009 | 1993 Ford Taurus

1 Answer

How change headlight on hyundai 2001 xg300


Remove the head lamp and disconnect the head lamp connector. 0f7fe9f.jpg Remove three 10mm bolts Unscrew the headlamp bulb CAPS to access bulbs. 5502d76.jpg

Jun 13, 2009 | 2001 Hyundai XG300

1 Answer

Drivers side head lamp assy removal


if it is the torx head screw on the bottom, the metal feral might be spinning n plastic housing.

Feb 02, 2009 | 1997 Jaguar XK8

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...