Question about Chevrolet Impala

Open Question

Replacing a 2002 impala radiator support bracket

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove radiator on 2000 Impala


Removing the radiator requires more space than I am allowed here.

I have a 2002 Impala, and replaced the condensor (and removed the radiator)
I did a complete write-up at North America Impala www.naioa.com
http://www.naioa.com/v2/modules.php?name=Forums&file=viewtopic&t=31404.
You'll probably have to register for free to see the write-up.
Look under the Forums and then "Knowledge Database".

Here's a couple pictures:

.
first.jpg
second.jpg
.
third.jpg

fan2.jpg

Dec 28, 2010 | 2000 Chevrolet Impala

1 Answer

How to replace a radiator for a 2000 chevy impala


My Impala is a 2002 with a 3.8L. I had to replace my condensor and therefore remove my radiator. I wrote it up and saved the instructions and pictures at:
http://www.naioa.com/v2/modules.php?name=Forums&file=viewtopic&t=31404
I hope this helps, and good luck.

Jul 30, 2010 | 2000 Chevrolet Impala

1 Answer

Need to locate and replace coolant sensor


If you are refering to the coolant level sensor (causes low coolant light to turn on), it is located on the radiator near the battery on the passnger side. It is on the radiator tank, just below the radiator cap and the upper connection for the transmission line. Heres a picture of the sensor on my 2002 Impala when I removed the radiator (it's the square thing in the center of the picture):

07b01b9.jpg

Jul 12, 2010 | 2002 Chevrolet Impala

1 Answer

Dipstick 2002 impala


yellow handle, should be right there? between the motor and radiator?

May 13, 2010 | 2002 Chevrolet Impala

1 Answer

2002 chevy impala...wipers stay in the up position. why do i get a replacement transmission and install?


No what you need to ck first is take the windshield cowl cover off (the plastic cover at the bottom of the windshield) Then ck the wiper mounting bracket you will see a oval looking thing with a spring wraped around it on top of the wiper mtr. On the bottom of the oval is a little lever.ck and make shure that is still there.If it is than ck the big bracket under the crank arm there is a little tab sticking up (towards the left side at the back of the bracket.) that lever on the crank arm needs to hit the tab on the bracket when the wipers are turned off. If the lever is there than bend the tab untill the lever hits the tab. If the lever is missing on the crank arm than the crank arm needs to be repalced.Follow the instructions with the crank arm to the letter.

Feb 25, 2010 | 2002 Chevrolet Impala

1 Answer

My 2002 Impala has an A/C leak. The leak is on the driver's side around the top of the radiator but I'm unable to see the actual leak. Is this a condenser issue or possibly just an o-ring?


On my 2002 3800 V6 Impala the leak was at the bottom of the condensor on the drivers side. On mine the condensor connections were near the bottm driver's side. If you sure it's at the top, it's pretty certain to be the condensor.
I replaced my own. As I recall, the condensor was less than $100.

Jul 05, 2009 | 2002 Chevrolet Impala

1 Answer

Replace the radiator


Removal and Installation
On all engines
  1. Drain the engine cooling system. For additional information, refer to Cooling System Draining, Filling And Bleeding in this section.
  1. Remove the upper radiator sight shield.
  1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .
  1. Remove the six bolts and the two radiator upper support brackets.
  1. NOTE: 3.9L shown; 3.0L similar.
    Remove the upper radiator hose.
  1. Remove the bolt and position the receiver drier aside.
  1. Disconnect the dual flow coolant valve electrical connector and the A/C line from the fan shroud.
On 3.0L engines
  1. Disconnect the throttle position (TP) sensor and the idle air control (IAC) valve electrical connectors.
  1. Remove the bracket.
    1. Remove the bolts.
    1. Remove the bracket.
    1. Disconnect the high pressure cooling fan bracket and line.
    1. Using the appropriate special tool, install a new O-ring on the power steering pressure hose fitting.
    1. Separate the return hose from the fan shroud and position aside.
    1. Remove the two bolts and position the fan shroud assembly.
    1. Disconnect the return hose from the cooling fan and shroud and remove the cooling fan and shroud assembly.
    1. Remove the A/C condenser. For additional information, refer to Section 412-03 .
    1. Disconnect the lower radiator hose.
    1. Remove the two bolts and position the multi-cooler assembly aside.
    1. Remove the bolts and the condenser support brackets.
    1. Remove the radiator.

Apr 29, 2009 | 2002 Lincoln LS

1 Answer

Winshield wipers stay stright when you turn them off 2002 chevy impala


You need to replace the wiper crank arm that is bolted to the wiper motor. Then you need to bend the tab back up that got bent on the wiper motor bracket that the old crank arm bent. The crank arm has to hit this metal tab so the wipers will park down below the window istead of up.

Mar 06, 2009 | 2002 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...