Question about 2005 GMC Envoy

Open Question

2005 gmc envoy axle nut size - 2005 GMC Envoy

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

hotrodtod38
  • 141 Answers

SOURCE: 2005 gmc envoy emissions light

maybe fuel fiter

Posted on Feb 15, 2009

Molson02536
  • 3854 Answers

SOURCE: 2005 GMC Envoy Locked in 4WD all the time

If your luck it's going to be a $15.00 vacuum switch on the transfer case that takes about 15 min to replace, if it's the electronic solenoid to the transfer case then it's going to be cost a little more and take a little longer. If your try switching from 4WD to 2WD and hear the solenoid working by hearing the cluck's when it engages and disengage then it's going to be the vacuum switch on top of the transfer case on the drivers side. Auto Zone Sell's them for $15.00 and they will have the step by step instructions to replacing the switch. They will also have the transfer case solenoid  too, if you don't hear the solenoid. Check the fuses, the fuse may have gone bad. Good luck and hope this helps.

Posted on Jun 19, 2009

  • 43 Answers

SOURCE: i have a 2005 gmc envoy and the driver seat gets hot

There may be a stuck relay Stuck in the "On" position. A relay is a remote switch that does the heavier work of a smaller or more delicate switch. It is probably under the seat but if you have "memory" seats that move the power seats back and forth it is probably the control box causing the problem. It has relays inside it.

Posted on Jun 30, 2009

canbruce75
  • 1776 Answers

SOURCE: I need the torque spec for the axle and the axle

Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Posted on Aug 18, 2009

Testimonial: "hey thanks for the help"

  • 95 Answers

SOURCE: I have 2005 GMC Envoy. I noticed the gas

The new design filler neck on newer gm vehicles don't have a flap. The flap was just to keep stuff from falling in. I've had problems with the fuel sending unit in the tank on these vehicles.

Posted on Jan 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

09 gmc canyon front hub nut size


Measure the nut in fractional size & divide by .0395
Then you will have your metric axle nut size.
34,36mm etc.

One would assume you work on your own vehicles,that you
have all the sockets, in 1/2" drive, from 10 thru 36mm

May 31, 2012 | 2009 GMC Canyon

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

How do u replace a front wheel bearing on a 2005 gmc envoy 4x4 and dose anybody have diagrams to follow how to


Remove center hub cap. Remove large nut behind hub cap.Lift wheel assembly off ground. Remove wheel. Remove brake calipher assembly by taking out larger bolts from back of calipher. Remove brake rotor. Pull axle toward middle of vehicle, you may have to tap axle end with small hammer being careful not to damage threads on end of axle. Remove three bolts from back, bearing housing should come out to the front.

Jul 12, 2010 | 2005 GMC Envoy

1 Answer

WHERE THE CV JOINT COMES OUT OF THE AXLE IT IS LOSE. IS THERE A NUT THAT IS COMEING OFF .I NEED A PARTS DIAGRAM.


If I am reading your question correctly, it does sound like the axle nut is loose. Is the cv axle loose near the wheel? I am not familiar with the envoy design so I don't know how to get to the nut. You may have to take the wheel off or there will probably be some sort of cap over it. You will need to find out what the nut is supposed to be torqued to and get a cotter pin on it, those types are usually a big castle nut. Good luck!

Mar 05, 2010 | 2005 GMC Envoy

1 Answer

How do I remove front axel from 2004 envoy


required a little bit of works
remove the wheel
loose the tie rod end, lower ball joint, axle nut
separate the steering knucke assembly from the axle
remove the axle, you may have to use a pry bar to pry it out of the transmission

Feb 28, 2010 | 2004 GMC Envoy

1 Answer

2002 gmc envoy xl front wheel bearing assy replace


take the wheel off,take the axle nut off,disconnect the spindle from the ball joint or joints, take the tie rod end out of the spindle and remove the spindle leaving the axle in the transmission. Now there is three bolts on the back of the spindle take theese out and beat the hub and bearing assy out. The new one wont be as hard to put in as the old one was to come out.

Dec 30, 2009 | 2002 GMC Envoy

2 Answers

How to replace front wheel bearing on 2003 GMC ENVOY


Jack up vehicle and support with jack stands
Take off wheel
remove brake caliper
remove caliper bracket
remove rotor
remove axle retaining nut cotter pin
remove axle retaining nut
remove axle from output flange
pull axle out of vehicle
hub and bearing assembly held in by 4 bolts

installation is reverse of removal. You will need to find out the torque specs for the axle retaining nut.

Jan 14, 2009 | 2002 GMC Envoy

Not finding what you are looking for?
2005 GMC Envoy Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...