Question about 2000 Jeep Grand Cherokee

1 Answer

Is the cam counter bad would that make it fire out of time

Wayne 2000 jeep grand cherokee

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 278 Answers

Cam Sensor? Not sure exactly but will make for harder starts and even an occasional no start situations. Also rough running idle and poor performance.

Posted on Oct 29, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: setting timing on a 2002 jeep grand cherokee

how do you set the timing on jeep laredo 2002?

Posted on Oct 18, 2008

whispers76
  • 55 Answers

SOURCE: Changing the water pump on 2000 Jeep Grand Cherokee V6

WATER PUMP
The water pump is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

If water pump is replaced because of bearing/shaft damage, or leaking shaft seal, the mechanical cooling fan assembly should also be inspected. Inspect for fatigue cracks, loose blades, or loose rivets that could have resulted from excessive vibration. Replace fan if any of these conditions are found. Also check condition of the thermal viscous fan drive. Refer to Viscous Fan Drive in this group.

The water pump can be removed without discharging the air conditioning system (if equipped)

REMOVAL
Disconnect negative battery cable from battery.
Drain cooling system. Refer to Draining Cooling System in this group.
Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.

The thermal viscous fan drive is attached (threaded) to the water pump hub shaft. Remove fan/viscous fan drive assembly from water pump by turning mounting nut counterclockwise as viewed from front. Threads on viscous fan drive are RIGHT HAND. Using special tool spanner wrench 6958 with adapter pins 8346 and a suitable fan wrench loosen the fan drive Viscous Fan and Fan Drive Do not attempt to remove fan/viscous fan drive assembly from vehicle at this time.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS SPECIAL CLAMP TOOL (NUMBER 6094) SNAP-ON CLAMP TOOL (NUMBER HPC-20) MAY BE USED FOR LARGER CLAMPS. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

If water pump is being replaced, do not unbolt fan blade assembly from thermal viscous fan drive.
Remove two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware Do not attempt to remove fan shroud at this time.
Remove fan shroud and fan blade/viscous fan drive assembly from vehicle as a complete unit.
After removing fan blade/viscous fan drive assembly, do not place thermal viscous fan drive in horizontal position. If stored horizontally, silicone fluid in viscous fan drive could drain into its bearing assembly and contaminate lubricant.
Remove accessory drive belt as follows: The drive belt is equipped with a spring loaded automatic belt tensioner. Relax tension from belt by rotating tensioner clockwise (as viewed from front) Automatic Belt Tensioner - When all belt tension has been relaxed, remove accessory drive belt.
Remove lower radiator hose clamp and remove lower hose at water pump.
Remove seven water pump mounting bolts and one stud bolt
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

Remove water pump and gasket. Discard gasket.
INSTALLATION
Clean gasket mating surfaces.
Using a new gasket, position water pump and install mounting bolts as shown. Water Pump Installation - Tighten water pump mounting bolts to 54 N·m (40 ft. lbs.) torque.
Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
Connect radiator lower hose to water pump.
Relax tension from belt tensioner Automatic Belt Tensioner - Install drive belt
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to Belt Routing for correct belt routing. Or, refer to the Belt Routing Label located in the engine compartment. The correct belt with correct length must be used.

Position fan shroud and fan blade/viscous fan drive assembly to vehicle as a complete unit.
Be sure the upper and lower portions of the fan shroud are firmly connected. All air must flow through the radiator.
Install two fan shroud-to-radiator nuts Fan Shroud Mounting Hardware
Be sure of at least 25 mm (1.0 inches) between tips of fan blades and fan shroud.
Install fan blade/viscous fan drive assembly to water pump shaft.
Fill cooling system. Refer to Refilling the Cooling System in this group.
Connect negative battery cable.
Start and warm the engine. Check for leaks

Posted on Jan 10, 2009

  • 2 Answers

SOURCE: How to replace headlights on 2000 Jeep Grand Cherokee

One long bolt at the top - requires a 7mm socket to remove the bolt. The light housing will pry out with a screw driver. There are three ball and socket type connectors that hold the housing in and I just pryed off the plastic housing carefully and "balls" pop out of the sockets. Finally, I was replacing the faded plastic housing and it came with a new wiring harness. It's impossible to reach the connector to use the new wiring harness that comes with the new plastic light housing. So just use the existing wiring harness with the new light assembly.

Posted on Feb 06, 2009

Molson02536
  • 3854 Answers

SOURCE: how do you change the tps on a 2000 jeep grand 4.7

The exact placement of the throttle position sensor generally is located on the side of the throttle body below the air intake tube on top of the engine.

To replace simply remove the air intake duct (usually one plastic screw), locate the sensor, disconnect wire plug in, remove the two sensor mounting screws (torx screw variety, size not remembered) and the sensor will come off. When replacing be sure to line up the throttle shaft with the proper groove inside the sensor...it should just slip in there pretty easily with a little bit of wiggling. Reinstall doing the reverse of the above.

Take's about 5 - 10 min to replace from start to finish and remember to clean the throttle body before starting this job to ensure no dirt will enter the engine. Good luck, Merry Xmass

Posted on Dec 24, 2009

  • 1 Answer

SOURCE: Replacing water pump on 2000 Jeep Grand Cherokee V6

i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ive tried to replace my pcm in my 94 jeep grand cherokee with used ones from a junkyard. I made sure part # was exact and made sure vehicles they came from did not have security systems. All three times I...


3 times, same symptoms-must be something else. Check crank position sensor and cam position sensor. Crank sensor is for ignition timing-advance and retard. Cam sensor is for fuel injector synchronization. If one is bad, it may cause problems like yours. Just a suggestion.

Nov 20, 2013 | 1994 Jeep Grand Cherokee

1 Answer

Changed coil in 1993 jeep grand cherokee lerado still not getting fire from coil


Have your ignition module checked. Also check codes for bad reference signal for cam or crank sensor.

Jul 29, 2012 | 1993 Jeep Grand Cherokee

1 Answer

On my 1999 jeep cherokee i change spark plugs and wires but number three cylinder still not firing consistently what could it be


Could be...no spark, no pulse to the fuel injector, no fuel out of the injector, bad compression due to poor rings or a bad valve, bad cam lobe, or lifter.

Jul 15, 2011 | 1999 Jeep Grand Cherokee

2 Answers

01 Jeep grand cherokee laredo won't start. No fire is going to engine. Changed spark plugs but didn't help at all


you might want to check you cam shaft sensor amd also there is a different sensor under the distutor i had to replace both of these on my 95 jeep grand cherokee laredo

Dec 04, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I own a 2000 jeep grand cherokee limited...I only get cold air coming out of the passenger side heat, driver side works fine...I think i need new blend doors.. Here are the fault codes i am receiving and...


Do you have dual zone control on the heat a/c control? It's been my experience that is the first thing to go. The blend door is more of a problem between blends, Like bi-level (defrost and floor etc..)

Feb 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

1996 Jeep Grand Cherokee Laredo won't fire. Was


check the cam sensor and crank sensor, also is the distributor turning,possible distributor gear pin broke

Nov 08, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Looking for the proper firing order diagram for a 2000 Jeep Grand Cherokee


Firing Order 4.0L 6 Cyl = 1-5-3-6-2-4
Firing Order 4.7L V-8 = 1-8-4-3-6-5-7-2

For more details check the repair manual: Section-08d-Ignition-System-Ewj8d (page 21 / Ignition Timing).

Good luck (remember rated this help).

Sep 08, 2009 | 2000 Jeep Grand Cherokee

2 Answers

When i drive my 2000 jeep grand cherokee some times it just shuts off and i cant get it started for 10 min at a time or some times after it runs it would only go 50 yards or so and then shuts off. im...


Check the automatic shutdown relay (ASR) in your fuse box under the hood close to the battery. Try switching the relay with an other relay and see if your still have the problem, the other thing that can cause this is a bad sensor like the cam shaft sensor or crank case sensor going bad. Try switching the relay first then if there is no change, try pulling a dtc code from the computer, Here is a link and hope it helps, keep me posted. Be glad to help http://www.allpar.com/fix/codes.html

Jun 19, 2009 | 2000 Jeep Grand Cherokee

3 Answers

1995 JEEP GRAND CHEROKEE RAN AND DIED WILL NOT START


IS IT THE 4.0L?IF SO U MAY HAVE A BAD CRANKSHAFT POSITION SENSOR.

Apr 28, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Jeep grand cherokee power seats


Try hitting the seat motor with a small hammer while you move the seat switch.

Oct 10, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...