Question about 2006 Subaru Forester

Open Question

Water in headlight of subaru forester - 2006 Subaru Forester

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 2006 SUBARU FORESTER HEADLIGHTS

open hood,unplug wire to bulb,pulloff rubber boot.There is a paperclip like thing you squeeze,ant bulb will come out.reverse the order.ok

Posted on Aug 21, 2008

  • 1986 Answers

SOURCE: How do i adjust the headlight beam on my Subaru

on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 14, 2009

techbuster
  • 5081 Answers

SOURCE: how to change a headlight in a 2005 subaru

THE BELOW IS THE PROCEDURE FOR REPLACEMENT OF BULB IN THE HEADLIGHT, IT ALSO CONTAINS DETAILS HOW TO REMOVE HEAD LIGHT ASSEMBLY ALSO
So step one - go get 3 (or 4 if you replace turn signal) bulbs. The front marker and side marker are the same bulb type.

Step two - remove the middle grill. The top connectors are visible and you can use a flat-bladed screw driver to compress the side or top and jiggle them so they pop loose. One you get the top part of the grill loose - DO NOT just pull outward - you will break the non-visible two lower connectors and get to go to the dealer again to get new ones. Instead, to remove the grill once the top part is loose, PULL UP. These light gray lower connectors are inbedded in the Head Lamp assembly.

The exterior trim piece is next. The two top black poppers need to be jimmied up 1/4 inch and then they pull out. The trim piece has 3 additional attachment points that are hidden. About the middle and a few inches to the outbound side, there are 2. They have an outbound facing notch, and the trim piece needs to be tapped towards the outward direction (side of the car) until it is free of them. This piece can flex a bit - its OK - but don't overdo. The final attachment is at the outermost corner that is a 1/4" male that plugs into a female fitting - This can be carefully pulled out and the trim piece is off.

The next part is the Head Lamp Assembly. There are 3 screws which the owners Manual actually correctly identifies. These come out. And the assembly is basically loose, but attached by 4 cables going into the Assembly. The Marker lights and turn signal are easy - just untwist them. When you reconnect them - they have VERY different slot keys, so you won't have trouble remembering which is which. The tough one is the headlamp.
The connector to the bulb has a rubberized cover. You can't see it while it is in place,but it has the word "PUSH" and two arrows on it pointing at the sides. You need to press in on the sides, a little higher than the middle, and disconnect the bulb connector. I had to gently use channel locks to do this.

When the connector is removed, you can remove the rubber dam material surrounding the light. It may stick, but this entire thing will come off, making removal of the bulb a much simpler task.

Once this is removed, you will see a wire latch holding the lamp in. Squeeze the wire latch (like pinching a clothes pin - kind of) at the top and it should release the bulb, which can now be simply removed from the enclosure.

Replacement is the reverse and will be much easier now that you see all the parts that were previously hidden. So step one - go get 3 (or 4 if you replace turn signal) bulbs. The front marker and side marker are the same bulb type.

Step two - remove the middle grill. The top connectors are visible and you can use a flat-bladed screw driver to compress the side or top and jiggle them so they pop loose. One you get the top part of the grill loose - DO NOT just pull outward - you will break the non-visible two lower connectors and get to go to the dealer again to get new ones. Instead, to remove the grill once the top part is loose, PULL UP. These light gray lower connectors are inbedded in the Head Lamp assembly.

The exterior trim piece is next. The two top black poppers need to be jimmied up 1/4 inch and then they pull out. The trim piece has 3 additional attachment points that are hidden. About the middle and a few inches to the outbound side, there are 2. They have an outbound facing notch, and the trim piece needs to be tapped towards the outward direction (side of the car) until it is free of them. This piece can flex a bit - its OK - but don't overdo. The final attachment is at the outermost corner that is a 1/4" male that plugs into a female fitting - This can be carefully pulled out and the trim piece is off.

The next part is the Head Lamp Assembly. There are 3 screws which the owners Manual actually correctly identifies. These come out. And the assembly is basically loose, but attached by 4 cables going into the Assembly. The Marker lights and turn signal are easy - just untwist them. When you reconnect them - they have VERY different slot keys, so you won't have trouble remembering which is which. The tough one is the headlamp.
The connector to the bulb has a rubberized cover. You can't see it while it is in place,but it has the word "PUSH" and two arrows on it pointing at the sides. You need to press in on the sides, a little higher than the middle, and disconnect the bulb connector. I had to gently use channel locks to do this.

When the connector is removed, you can remove the rubber dam material surrounding the light. It may stick, but this entire thing will come off, making removal of the bulb a much simpler task.

Once this is removed, you will see a wire latch holding the lamp in. Squeeze the wire latch (like pinching a clothes pin - kind of) at the top and it should release the bulb, which can now be simply removed from the enclosure.

Replacement is the reverse and will be much easier now that you see all the parts that were previously hidden.

Posted on Oct 11, 2009

techbuster
  • 5081 Answers

SOURCE: changing the bulb in a Subaru headlight

This is not a trivial job. I would recommend you get all four bulbs for whatever side you are replacing - do them all. The dealer-dude didn't have the orange turn-signal bulb in stock, and said they don't see too many replaced. I guess thats probably right since it was about ten years ago when I last saw someone actually use their turn signal.

So step one - go get 3 (or 4 if you replace turn signal) bulbs. The front marker and side marker are the same bulb type.

Step two - remove the middle grill. The top connectors are visible and you can use a flat-bladed screw driver to compress the side or top and jiggle them so they pop loose. One you get the top part of the grill loose - DO NOT just pull outward - you will break the non-visible two lower connectors and get to go to the dealer again to get new ones. Instead, to remove the grill once the top part is loose, PULL UP. These light gray lower connectors are inbedded in the Head Lamp assembly.

The exterior trim piece is next. The two top black poppers need to be jimmied up 1/4 inch and then they pull out. The trim piece has 3 additional attachment points that are hidden. About the middle and a few inches to the outbound side, there are 2. They have an outbound facing notch, and the trim piece needs to be tapped towards the outward direction (side of the car) until it is free of them. This piece can flex a bit - its OK - but don't overdo. The final attachment is at the outermost corner that is a 1/4" male that plugs into a female fitting - This can be carefully pulled out and the trim piece is off.

The next part is the Head Lamp Assembly. There are 3 screws which the owners Manual actually correctly identifies. These come out. And the assembly is basically loose, but attached by 4 cables going into the Assembly. The Marker lights and turn signal are easy - just untwist them. When you reconnect them - they have VERY different slot keys, so you won't have trouble remembering which is which. The tough one is the headlamp.
The connector to the bulb has a rubberized cover. You can't see it while it is in place,but it has the word "PUSH" and two arrows on it pointing at the sides. You need to press in on the sides, a little higher than the middle, and disconnect the bulb connector. I had to gently use channel locks to do this.

When the connector is removed, you can remove the rubber dam material surrounding the light. It may stick, but this entire thing will come off, making removal of the bulb a much simpler task.

Once this is removed, you will see a wire latch holding the lamp in. Squeeze the wire latch (like pinching a clothes pin - kind of) at the top and it should release the bulb, which can now be simply removed from the enclosure.

Replacement is the reverse and will be much easier now that you see all the parts that were previously hidden.

Posted on Jan 17, 2010

  • 10 Answers

SOURCE: 2000 subaru forester ignition coil wiring

Are there any other possible problems, or you are just not receiving spark at all now?

The coilpack could be dead and just need replaced. If you have a voltmeter or a test light, check the wiring on both sides of the coilpack harness to make sure it is receiving power.
I don't believe Subaru used ignitors past '99, but if they did, your should be located on the firewall behind the throttle body. Make sure it's plugged in and receiving power.

Coil packs do go bad from time to time. I had to replace mine in my
'98 Impreza a while back.

Goodluck!

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 99 subaru foresters headlights wont come on but the high beams and parking lights do. How can i fix it?


I would start simple and check the fuses and relays, also check the headlight switch to make sure your getting power out of it.

Feb 24, 2017 | 1999 Subaru Forester

2 Answers

How do you aim headlights on 1998 subaru forester


Each Headlight should have 2 adjusters directly behind where the lamp assy is fitted inside the engine bay. 1 will screw in or out to adjust the headlight left to right, the other adjusts up or down.

Apr 13, 2015 | 1998 Subaru Forester

1 Answer

Our 2002 Subaru Forester's headlights keep shutting off like there is a short. When we slam our hood sometimes one of them comes back on.


The headlight relay(s) could be defective. You should be able to read 12 volts at 15A FUSES 8 and 9. A defect in the DRL circuit also could affect operation.

Jan 30, 2015 | 2002 Subaru Forester

1 Answer

2000 subaru forester. lost the passenger headlight clamp. Can I just buy that part? Light works fine but keeps falling out.


try a scrap yard first the part will be less expensive otherwise your local dealership can get a replacement part.

Sep 03, 2011 | 2000 Subaru Forester

1 Answer

Instructions for replacing headlight bulb for '98 subaru forester.


Open the hood, reach behind the headlight assembly and carefully turn the lamp assembly counter-clockwise, then remove the pigtail. To install a new lamp, simply do the reverse procedure.

Jan 09, 2011 | 1998 Subaru Forester

1 Answer

I need to remove Subaru Forester headlight bulb


PULL BACK RUBBER BOOT BEHIND HEAD LITE UNSNAP CLIP THAT HOLS BULB IN ,REMOVE BULB INSTALL NEW ONE SNAP CLIP BACK ON SO IT DOESN'T FALL OUT,PUT RUBBER BAK ON,KEEPS WATER OUT

Dec 19, 2010 | 1998 Subaru Forester

1 Answer

Will a left headlight from a Subaru Forester 99 fit a Subaru Forester 98?


Yes. There are 2 types available. A 1 piece and a 2 piece. The 2 piece has a seperate turn signal. Good luck and have a good day.

May 26, 2010 | 1998 Subaru Forester

1 Answer

2006 SUBARU FORESTER HEADLIGHTS


open hood,unplug wire to bulb,pulloff rubber boot.There is a paperclip like thing you squeeze,ant bulb will come out.reverse the order.ok

Aug 07, 2008 | 2006 Subaru Forester

Not finding what you are looking for?
2006 Subaru Forester Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...