Question about Mazda Tribute

1 Answer

Code 118'112'122 It starts but no throttle respose

Posted by on

  • Allan Ordonez Oct 28, 2012

    And replaced TPS sensor

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,212 Answers

TPS wiring may not be connected, damaged or grounded/pinched, The new sensor may be damaged, or it may be well out of range due to not being cycled once prior to securing to make sure of correct engagement with throttle shaft.

And also possibly the throttle cable itself may have become disconnected or damaged

Posted on Oct 28, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Start and dies, codes p061f, p2106,p2104,p2111


code p2106 refers to throttle actuator control (TAC) system--limited power mode===causes ---wiring---TAC motor---APP sensor---ECM

code o2104 refers to TAQC systems ---forced idle mode===causes wiring---TAC motor--APP sensor--ECM

code p2111 refers to TAC system --actuator stuck open ==causes ---throttle body--throttle valve tight/ sticking

code p2111 also refers to TAC system --circuit malfunction==causes wiring---short to positive--short to ground---TP sensor---ECM

code p2111 also has a 3rd section---brake vacuum---implausible signal===causes---wiring---vacuum sensor--mechanical fault

Dec 21, 2013 | 2005 Ford Crown Victoria

1 Answer

Engine stalls under acceleration, shows code P1580, changed throttle body with new one but problem persists


I would worry or be concerned about the code.
The code is about the throttle sensor or actuator. If the sensor is faulty or the computer is not getting a good signal from the sensor it does not know what the throttle position is.
You might try resetting the throttle position - clear the code, key on but don't start, hold pedal to the floor, key off.

Aug 25, 2012 | Cars & Trucks

1 Answer

Code p2111


THE THROTTLE [FOOT PEDAL] AND THE THROTTLE PLATE ARE MOVING AT DIFFERENT ANGLES.MOST LIKELY THE THROTTLE PLATE IS CARBONED UP.REMOVE AIR INLET DUCT WORK AND OPEN THE THROTTLE PLATE,WITH A TOOTH BRUSH IN ONE HAND AND A CAN OF THROTTLE BODY CLEANER IN THE OTHER START SCRUBBING UNTIL ALL CARBON/VARNISH IS REMOVED.DISCONNECT BATTERY FOR 10 MINUTES TO CLEAR CODE AND DRIVE IT.IF CODE RETURNS THE DIAG WILL REQUIRE A MANUAL AND A VOLT/OHM METER AND LOTS MORE TIME.

Dec 07, 2011 | 2006 Kia Amanti

1 Answer

1990 chev K2500 5.7 TBI driving down highway and just quit like i turned it off. pulled over will idle fine but off idle tries to die. after shutoff for a few minutes starts an has throttle respose for a...


Fuel injection needs 20-30 pound pressure to fire the injectors. Try to check pressure before filter. If its low your pump is no good. If its ok then you have pressure drop after the filter. Filter on backwards or clogged.

Nov 25, 2010 | 1990 Chevrolet K2500

2 Answers

99 passat 2.8, vehicle was driven the night


That code is a Throttle Position Malfunction code.

This means one of two things:
1. The throttle body needs replaced
2. After the dead battery, you need to adapt the the throttle body.

The cheap way to do this is to leave the driver's door open, turn the key to the on position, but do not start the car. You will hear the throttle body self-adjust. This may take up to 2 minutes. That should get it close enough. To get it perfect requires a trip to the dealership.

If it does not help, the throttle body might be dead.

Dec 18, 2009 | 1999 Volkswagen Passat

1 Answer

My 00 pontiac grand prix starts 3 seconds and shuts down


P1122 is a throttle position sensor code. P1629 is a theft deterrent system code. P1122 will set when the voltage signal from the throttle position sensor drops below 0.1 volts. Normally, the sensor should measure between 1 volt at idle and 4 volts at full throttle. A failed throttle position sensor could easily cause your problem.

As for the theft deterrent system code, with that code set, the car shouldn't start at all (if the code is active). With P1629, the engine computer should refuse to deliver fuel to the engine. This code can be stored for up to 40 warm up cycles before clearing itself, so unless it is currently active, there may not be any need to worry about it.

I would inspect the wiring and connectors leading to the throttle position sensor. If that wiring is good, I would replace the sensor and see where that got me. Give that a try and let us know how things go.

Jul 28, 2009 | 1998 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...