Question about 2002 Saturn L-Series

1 Answer

I just installed a new timing chain on 02 saturn l100. followed all instructions. rotated engine so chain rolled five times and coloed links do not line up with marks on sprockets. am i doing somethin

See above

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saturn Master
  • 22,156 Answers

No it will only alighn something like every 300 or so turns ,youre all ok

Posted on Oct 28, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

GM Elec
  • 1000 Answers

SOURCE: wiper motor replacement 2001 saturn l100

Steve, You can find information at several web sites. One is All Data but they will charge you for each individual vehicle but Auto Zone will provide most vehicles for free.
Good luck.
Regards,

Posted on Feb 12, 2009

  • 186 Answers

SOURCE: changed timing chain and need to align to cam with the crang

Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

Posted on May 22, 2009

  • 543 Answers

SOURCE: my '02 saturn l100 starts shaking really bad

when your car is shaking and the light blinks thatmeans its misfiring,not running on all cylinder,,,

Posted on Oct 05, 2009

postings909
  • 130 Answers

SOURCE: I am replacing the timing chain on my 02 saturn. I

okay i posted you a picture of the postion. be carefull not to turn the crank or the cams or you will damaged the valves. let me know if you need more hlep.

Posted on Jul 23, 2010

  • 300 Answers

SOURCE: Okay. I'm fixing my 1994

It is not rare for people to have problems with engine after replacing the timing belt. In all my cars I do it by myself. It is not impossible, but you will spend more time than a professional. If you decide to do it by yourself, then get the Haynes Repair Manual (Based on a complete tear down and rebuilt), specific for your car. I have one for each of my cars. Go to the part Engine, and use the chapter Timing belt removal inspection, and Top Dead Center (TDC) location, and put the number one piston at TDC on the compression stroke. This can be found by putting the thumb over the spark plug hole and the pressure will push your finger upward till piston reaches the upper point. You have the crank shaft with a wrench. Now you are in compression stroke. To locate Top Dead Center Location, this can be done by inserting a long blunt object into the spark plug hole. Note the point where the object stops moving out this is the TDC.
Are you sure that the piston at cylinder N#1 is at TDC on compression stroke. Please check it out, and if not correct.The timing marks can be lining up correctly, ONLY if the piston at cylinder N31 is at TDC in compression stroke. I repeat again in compression stroke.

Posted on Oct 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off


Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.
  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
117016938

  1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Remove the primary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installation.
  1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
117016941

  1. Lower the primary chain with left side sprocket through the left cylinder head opening.
NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
  1. Loosely position left side camshaft sprocket over camshaft hub.
  2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
  3. Position primary chain onto water pump drive sprocket (10).
  4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
  5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
  6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
  1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
117016942

  1. Purge oil from timing chain tensioner using the following procedure:
    1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
    2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
117016943

  1. Reset timing chain tensioner using the following procedure:
    1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
    2. Apply a downward force until tensioner is reset.
NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.
117016944

  1. Install the reset chain tensioner (1) into the right cylinder head.
  2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
117016945

  1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
  2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
  3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
117016946

  1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
117016947

  1. Install camshaft position sensor (2) and connect electrical connector.
  2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
  3. Install upper intake manifold.
NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
  1. Fill cooling system.

Mar 27, 2013 | 2001 Chrysler Concorde

1 Answer

When you rotate the sprockets the back one is out of time on a 1999 chrysler sebring lxi 2.5


the chain on the 2.5 engine has a very unique way of being timed.if you are replacing the chains there should be installation instructions to get the engine timed correctly. you have to follow the instructions to a"T".

Jun 09, 2012 | Chrysler Sebring Cars & Trucks

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

Need the timing marks for a 2000 alero


please let me know if you have questions.
2.4L Engine
NOTE It is recommended that the entire procedure be reviewed before attempting to service the timing chain.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following: Negative battery cable, Coolant surge tank, Accessory drive belt, Alternator
  4. Install an engine support.
  5. Remove or disconnect the following: Upper cover fasteners, Front cover vent hose, Right engine mount and bracket, Right front wheel, Right lower splash shield, Crankshaft balancer, Lower cover fasteners, Front cover
  6. Rotate the crankshaft clockwise, as viewed from front of engine (normal rotation) until the camshaft sprocket's timing dowel pin holes align with the timing chain housing holes. The crankshaft sprocket mark should align with the engine mark. The crankshaft sprocket keyway should point upward and align with the cylinder bores centerline. This is the normal timed position.
  7. Remove the timing chain guides.
  8. Remove the timing chain tensioner.
    NOTE Be sure all the slack in the timing chain is above the tensioner assembly when removing it. CAUTION The tensioner plunger is spring loaded and could fly out causing personal injury.
  9. Remove or disconnect the following: Timing chain, Camshaft sprockets

To install:
  1. Install or connect the following: Camshaft sprockets. Torque the bolts to 52 ft. lbs. (70 Nm),
    Camshaft sprocket alignment pin through the camshaft sprockets holes into the timing chain housing holes to position the camshafts for timing.
  2. If the camshafts are out of position and must be rotated more than 1 / 8 turn in order to install the alignment dowel pins, perform the following:
    1. Rotated the crankshaft 90 degrees clockwise off Top Dead Center (TDC) in order to give the valves adequate clearance to open.
    2. Once the camshafts are positioned and the dowels installed, rotate the crankshaft counterclockwise back to TDC.
      WARNING Do not rotate the crankshaft clockwise to TDC or valve and piston damage may occur.
  3. Install the timing chain over the exhaust camshaft sprocket, around the idler sprocket and around the crankshaft sprocket.
    jturcotte_2361.gifjturcotte_2362.gif

    Fig. Timing chain and sprocket alignment positions-2.4L DOHC engine

  4. Remove the alignment dowel pin from the intake camshaft. Using a dowel pin remover tool, rotate the intake camshaft sprocket counterclockwise enough to slide the timing chain over the intake camshaft sprocket. Release the camshaft sprocket wrench. The length of chain between the 2 camshaft sprockets will tighten.
    NOTE If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated.
  5. Leave the alignment dowel pins installed.
  6. With slack removed from chain between intake camshaft sprocket and crankshaft sprocket, the timing marks on the crankshaft and the cylinder block should be aligned. If marks are not aligned, move the chain 1 tooth forward or rearward, remove slack and recheck the marks.
  7. Tighten the chain housing to engine stud. The stud is installed under the timing chain. Torque it to 19 ft. lbs. (26 Nm).
  8. Reload the timing chain tensioner as follows:
    1. Form a keeper from heavy gauge wire.
    2. Slightly, compress the shoe plunger and insert a small screwdriver into the access hole.
    3. Release the ratchet pawl and compress the plunger completely into the hole.
    4. Insert the keeper between the access hole and the blade.
  9. Install or connect the following:
    Tensioner assembly to the chain housing. Torque the bolts to 89 inch lbs. (10 Nm). Tensioner shoe and retainer. Torque the bolts to 89 inch lbs. (10 Nm). NOTE Recheck plunger assembly installation. It is correctly installed when the long end is toward the crankshaft.
  10. Remove the alignment dowel pins. Rotate crankshaft clockwise 2 full rotations. Align the crankshaft timing mark with mark on cylinder block and reinstall alignment dowel pins. Alignment dowel pins will slide in easily if engine is timed correctly.
    WARNING If the engine is not correctly timed, severe engine damage could occur.
  11. Install or connect the following: Timing chain guides, New seal into the front cover by lubricating the seal lip and tapping it into place, Front cover and gaskets. Torque the nuts and bolts to 106 inch lbs. (12 Nm), Crankshaft balancer. Torque the bolt to 129 ft. lbs. (175 Nm), Right front lower splash shield, Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm), Right engine mount bracket. Torque the bolts to 81 ft. lbs. (110 Nm) plus an additional 90 degree turn, Right engine mount. Torque the bolt to 49 ft. lbs. (60 Nm), Upper cover vent hose
  12. Remove the engine support.
  13. Install or connect the following: Alternator. Torque the bolts to 37 ft. lbs. (50 Nm), Accessory drive belt, Coolant surge tank, Negative battery cable.
  14. Refill the cooling system.
  15. Start the engine and check for leaks.

Oct 04, 2011 | Cars & Trucks

1 Answer

I have a 2001 Olds Aurora with a V6 3.5 and I need the timing diagram for this. I have looked everywhere and can not find a book with it in it. Would you happen to have this??


Please let me know if you have questions, and thanks for using Fixya.


jturcotte_1505.gif

To install:

  1. Rotate the crankshaft so the No. 1 piston is at TDC and the mark on the crankshaft is at the 4 o-clock position.
  2. Rotate the balance shaft so the timing mark is at the 5 o-clock position.
    NOTE Be sure the painted links are facing the front of the engine.
  3. Install the timing chain on the sprockets.
  4. Center the mark on the left intake camshaft sprocket between the 2 painted links.
  5. Lift the chain onto the right intake camshaft sprocket. While doing this, align the marks on the balance shaft and crankshaft sprockets with the painted marks on the chain.
  6. Verify that all of the timing marks are aligned.
  7. Install the primary chain tensioner shoe. Torque the bolt to 22 ft. lbs. (30 Nm).
  8. Compress the primary chain tensioner using the following steps:
    1. Rotate the ratchet release lever counterclockwise and hold it.
    2. Press the tensioner shoe in and hold it.
    3. Release the ratchet lever and slowly release the pressure on the shoe.
    4. Insert a pin through the hole in the lever as the lever moves to the first click. The ratchet should hold the shoe in the compressed position.
      NOTE Be sure the lever on the tensioner is facing you when installed.

  9. Install or connect the following:

    Primary chain tensioner. Torque the bolts to 18 ft. lbs. (25 Nm); then remove the chain tensioner pin. 4 chain guide access plugs. Torque the plugs to 44 inch lbs. (5 Nm). Front engine lift bracket. Torque the hex head bolt to 37 ft. lbs. (50 Nm) and the internal drive bolt to 18 ft. lbs. (25 Nm). CMP sensor. Torque the bolts to 80 inch lbs. (9 Nm).
  10. Remove the camshaft holding tools.
  11. Place a small bead of RTV sealant on the 3 areas indicated in the diagram.
  12. Install or connect the following:

    Front cover with a new gasket. Torque the bolts to 124 inch lbs. (14 Nm) and the coolant drain plug to 89 inch lbs. (10 Nm). Crankshaft balancer. Torque the bolt to 37 ft. lbs. (50 Nm); then an additional 120 degree turn.
  13. Raise the engine cradle and install new bolts. Torque the bolts to 133 ft. lbs. (180 Nm).
  14. Coat the sub-frame bushings with rubber lubricant.
  15. Install or connect the following:

    Water pump with a new gasket. Torque the bolts to 124 inch lbs. (14 Nm). Belt tensioner. Torque the bolts to 37 ft. lbs. (50 Nm). Idler pulley. Torque the bolt to 37 ft. lbs. (50 Nm). Power steering pump pulley Drive belt Underhood accessory wiring junction block Washer and coolant reservoirs Battery and tray Front diagonal brace Rocker arm covers. Torque the bolts to 80 inch lbs. (9 Nm). Negative battery cable
  16. Refill the cooling system.
  17. Refill the crankcase.
  18. Start the engine and verify no leaks.
Secondary Chain
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the rocker arm cover and install camshaft holding fixture J-42038.
  4. Remove the camshaft sprocket bolts and install the timing chain holding fixture J-42042 on the cylinder head.
  5. Remove or disconnect the following:

    Sprockets and chain Secondary timing sprocket and chain
To install:

jturcotte_428.jpg

Fig. Correct sprocket alignment for the left secondary timing chain-3.5L engine


jturcotte_429.jpg

Fig. Correct sprocket alignment for the right secondary timing chain-3.5L engine

  1. Install or connect the following:

    Secondary timing chain on the sprockets, with the drive pins at the 12 o-clock positions Sprockets and chain assembly onto the camshafts, with the chain properly aligned on the tensioner
  2. Remove the timing chain holding fixture
  3. Install the sprocket bolts. Torque the bolts to 18 ft. lbs. (25 Nm); then an additional 45 degree turn.
  4. Remove the camshaft holding fixture.
  5. Install or connect the following:

    Rocker arm cover Negative battery cable

Apr 09, 2011 | 2001 Oldsmobile Aurora

1 Answer

Need directions on how to install a timing chain on a 2002 Saturn L series 2.2 liter along with the allignment marks for the intake and exhaust cams


To Install:
  1. Install or connect the following:
    • Timing chain drive sprocket to crankshaft
      1. Rotate the crank so the mark on the sprocket is at the 5 o'clock position
  2. Assemble chain to the intake camshaft sprocket alignment copper link to the "INT" diamond timing mark on the camshaft sprocket sat_car_22_tmng-chn_pos.gif

    NOTE: When lowering the timing chain rotate the assembly 90° to allow the chain to fall between the cylinder block bosses then rotate the assembly back so the camshaft sprocket is facing forward.
    sat_car_22_tmng-c_hsng_opng.gif

  3. Lower the assembly through the chain housing opening on top of the cylinder head. Use care to ensure that the chain goes around both sides of the cylinder block bosses NOTE: The crankshaft sprocket timing mark will be at approximately the 5 o'clock position.
  4. Route chain around crankshaft sprocket and align silver link to the timing mark sat_car_22_set_tdc.gif

    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  5. Install or connect the following:
    • Intake camshaft sprocket loosely onto the intake camshaft then install the new camshaft sprocket bolt finger tight NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    • Adjustable timing chain guide through the opening on top of the cylinder head then install the chain guide bolt; torque to 89 lb-in. (10 Nm) sat_car_22_ajst_tmng-ch_guid.gif

      sat_car_22_cm-shft_sprkt_blts.gif

    • Exhaust camshaft sprocket loosely onto the exhaust camshaft with the timing mark on the sprocket aligned with the silver link then install a new camshaft sprocket bolt finger tight
    NOTE: It is not necessary to align the sprocket-to-camshaft offset notch at this time.
    NOTE: The camshaft sprocket bolts are not reusable; they are torque-to-yield and must be discarded to prevent premature failure.
  6. Align the camshaft sprocket-to-camshaft then tighten the camshaft bolt using the following procedure: sat_car_22_crnk_tmng-c_mrk.gif

    NOTE: Do not rotate either camshaft more than 1/2 turn in either direction with the crankshaft at Top Dead Center (TDC). To do so may cause valve to piston contact resulting in a damaged valve and/or a damaged piston.
    • Ensure that the sprocket timing mark is at the 5 o'clock position
    • Rotate the intake camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
    • Rotate exhaust camshaft using a 24mm wrench on the flats of the camshaft until the sprocket-to-camshaft alignment notch seats
    • When the sprocket seats on the camshaft tighten the sprocket bolt finger tight
  7. Verify that all colored links are aligned with the appropriate marks on the camshaft and crankshaft sprockets NOTE: If they are not repeat steps 1C through 4.
  8. Install the fixed timing chain guide and bolts; torque to 89 lb-in. (10 Nm)
  9. Install the fixed timing chain guide bolt access hole plug; torque to 30 lb-ft. (40 Nm)
  10. Install upper timing chain guide and bolts; torque to 89 lb-in. (10 Nm) NOTE: Use a 24mm wrench to support the camshaft while applying torque to the camshaft sprocket bolt. Do not torque the camshaft bolts against the timing chain as it may damage the timing chain.
  11. Torque the intake and exhaust camshaft sprocket bolts; torque as follows:
    • First Pass: 63 lb-ft. (85 Nm)
    • Second Pass: Turn an additional 30° using a torque angle gauge
  12. Install the sealing ring and tensioner assembly; torque to 55 lb-ft. (75 Nm)
  13. Install or connect the following:
    • Timing chain oil nozzle and bolt; torque to 89 lb-in. (10 Nm)
    • Camshaft cover assembly
    • Engine front cover
    • Negative battery cable; torque to 13 lb-ft. (17 Nm)

Nov 12, 2010 | 2002 Saturn L-Series

1 Answer

How do i reset the timing in a 1997 z24 Chevrolet Cavalier 2.4 twin cam? Where are the timing marks on the cam gears?


2.3L and 2.4L Engines Before attempting to remove the timing chain, read the entire procedure.
  1. Disconnect the negative battery cable.
  2. Remove the timing chain front cover, as outlined earlier in this section.
  3. Rotate the crankshaft clockwise, as viewed from the front of engine/normal rotation, until the camshaft sprocket timing dowel pin holes line up with the holes in the timing chain housing. The crankshaft sprocket keyway should point upwards and line up with the centerline of the cylinder bores. This is the "timed'' position. Fig. 8: The chain must be in the "timed'' position - 2.3L and 2.4L engines 87953108.gif
    Fig. 9: Remove the timing chain guides 87953109.gif

  4. Remove the timing chain guides.
  5. Raise and safely support the vehicle.
  6. Make sure all of the slack in the timing chain is above the tensioner assembly, then remove the tensioner. The timing chain must be disengaged from any wear grooves in the tensioner shoe in order to remove the shoe. Slide a suitable prytool under the timing chain while pulling the shoe outward. WARNING
    Do NOT attempt to pry the socket off the camshaft or damage to the sprocket or chain housing could occur.
  7. If difficulty is encountered in removing the chain tensioner shoe, remove the intake camshaft sprocket, as follows;
    1. Carefully lower the vehicle.
    2. Hold the intake camshaft sprocket with a suitable tool and remove the sprocket bolt and washer.
    3. Remove the washer from the bolt and rethread the bolt back into the camshaft by hand. The bolt provides a surface to push against.
    4. Remove the camshaft sprocket using a three-jaw puller in the three relief holes in the sprocket.
  8. Unfasten the tensioner assembly retaining bolts, then remove the tensioner. NOTE: The timing chain and crankshaft sprocket MUST be marked before removal. If the chain or sprocket is installed with the wear pattern in the opposite direction, noise and increased wear may occur.
  9. Mark the crankshaft sprocket and timing chain outer surface for reassembly, then remove the chain.
  10. Clean the old sealant off the bolt with a wire brush. Clean the threaded hole in the camshaft with a round nylon brush. Inspect the parts for wear and replace as necessary. Note that some scoring of the chain shoe and guides is normal. To install: WARNING
    Failure to follow this procedure may result in severe engine damage.
  11. Position the intake camshaft sprocket onto the camshaft with the surface marked during removal showing.
  12. Install the intake camshaft sprocket retaining bolt and washer, tighten to 52 ft. lbs. (70 Nm) while holding the sprocket with a suitable tool. Use GM sealant 12345493 or equivalent on the camshaft sprocket bolt.
  13. Place GM tool J 36008, or equivalent camshaft aligning pins, through the holes in the camshaft sprockets into the holes in the timing chain housing. This positions the cams for correct timing.
  14. If the camshafts are out of position and must be rotated more than 1?8 turn in order to install the alignment dowel pins, proceed as follows:
    1. The crankshaft MUST be rotate 90°clockwise off of TDC in order to five the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft counter clockwise back to TDC. WARNING
      Do not rotate the crankshaft clockwise to TDC; valve or piston damage could result. NOTE: The side of the timing chain that was marked during removal must be showing when the chain is installed.

  15. Place the timing chain over the exhaust camshaft sprockets, around the idler sprocket and around the camshaft sprocket.
  16. Set the camshafts at the timed position and install the timing chain. Remove the alignment dowel pin from the intake camshaft. Using GM tool J 39579, rotate the intake camshaft sprocket counter clockwise enough to slide the timing chain over the intake camshaft sprocket. Release the camshaft sprocket wrench (J 39579 or equivalent). The length of the chain between the two camshaft sprockets will tighten. If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are NOT timed correctly and the procedure must be repeated.
  17. Leave the alignment dowel pins installed. Raise and safely support the vehicle.
  18. With the slack removed from the chain between the intake camshaft sprocket and the crankshaft sprocket, the timing marks on the crankshaft and cylinder block should be aligned. If the marks are not aligned, move the chain one tooth forward or rearward, remove the slack and recheck the marks. Fig. 10: Timing chain assembly retaining bolts - 2.3L and 2.4L engines 87953111.gif

  19. Reload the timing chain tensioner assembly to its "zero'' position as follows:
    1. Form a keeper from a piece of heavy gauge wire, as shown in the accompanying figure.
    2. Apply slight force on the tensioner blade to compress the plunger.
    3. Insert a small prytool into the reset access hole, and pry the ratchet pawl away from the ratchet teeth while forcing the plunger completely in the hole.
    4. Install the keeper between the access hole and the blade. Fig. 11: Reloading the tensioner to its "ZERO'' position, then install to the chain housing 87953110.gif

  20. Install the tensioner assembly to the timing chain housing. Recheck the plunger assembly installation, it is correctly installed when the long end is toward the crankshaft. Install the tensioner retaining bolts; tighten to 89 inch lbs. (10 Nm).
  21. Carefully lower the vehicle enough to reach and remove the alignment dowel pins. WARNING
    Severe engine damage could result if the engine is not properly timed.
  22. Rotate the crankshaft clockwise (normal rotation) two full rotations. Align the crankshaft keyway with the mark on the cylinder block and reinstall the alignment dowel pins. The pins will slide in easily if the engine is correctly timed.
  23. Install the timing chain guides, then install the front (timing chain) cover.
  24. Connect the negative battery cable.
prev.gif next.gif

Oct 02, 2010 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
2002 Saturn L-Series Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...