Question about Cars & Trucks

Open Question

Telko s008 alarm manual / code reset

Im looking for info on reseting the code on my alarm it has run down for some time but wont take the code any more is there a default code?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 118 Answers

SOURCE: How can I reset my Factory Alarm on my Jeep it wont run

Alarm Module Reset Procedure
NOTE: This information applies to a Vehicle Theft Security System (VTSS) that was armed when the battery was disconnected and reconnected.
When the armed VTSS senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed following a battery reconnection.
The power-up mode will also apply if the battery goes dead while the system is armed and battery jump-starting is attempted. The engine no-run feature will prevent the engine from starting until the alarm system has been actively or passively disarmed.
Passive disarming of the Vehicle Theft Security System (VTSS) occurs when the vehicle is unlocked using the key to unlock either front door or the lift gate. Active disarming of the VTSS occurs when the vehicle is unlocked by depressing the Unlock button of the Remote Keyless Entry (RKE) transmitter.
Once the alarm has been activated (horn sounding, lights flashing, and the engine no-run feature), either disarming method will deactivate the alarm.
Depressing the Panic button (if equipped) on the RKE transmitter will also disarm the VTSS, but the horn will sound and the lights will flash for about three minutes as part of the Panic feature. The horn and lights can be stopped by pressing any of the RKE transmitter's buttons or driving the vehicle above 15 mph.

Posted on Jan 28, 2009

  • 5 Answers

SOURCE: 01 tiburon, alarm reset? wont start

I had the same problem because I store my car in the garage in the winter. I found that replacing the positive/negative cables with new ones and also if you still have your spare key, try putting one key in the ignition and turn to acc before turning it over click your alarm button on your spare set of keys and the alarm should reset itself and the car should start. i hope this helps you, i just finished changing my spark plug wires because I had a code P302 which made my 2nd cylinder misfire, so if your tiburon is around 180,000 km then you should change it too, I recommend Bosch they are the best.
take care
Sven

Posted on Jun 26, 2009

  • 490 Answers

SOURCE: im trien to reset the factory car alarm and code

usually if you go to the dealer they wont charge you.Let them help!

Posted on Jul 23, 2009

  • 1 Answer

SOURCE: my alarm shut my whole car down and it wont start

My 95 Lexus es300 has been shut down by alarm system

Posted on Mar 02, 2010

johnjohn2
  • 5763 Answers

SOURCE: i can not reset the alarm module because of that

Im not sure if this is a factory alarm or aftermarket, try locking and unlocking the pass/side door and see if car starts. if its aftermarket look under the dash for a red button, this is a default button,turn the key on and push this button in four times fast. then try to start the car. hope this helps.

Posted on Sep 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alarm kill switch will not let me start car and pulls battary down


im working on a 97 ford f-150 with a 4.2 l itre engine ive replaced the coil pack on it.has a a spark to plugs,but wont start,tied to retreive codes off computer could not get none.not avaiable it said .Do you think the computer is out,let me know.

Sep 14, 2012 | 2005 Ford Focus

1 Answer

Telko model S002 alarm instructions


Look up the Manufacturer on the internet or write to them and request an owners manual and they will probably send you one for free.
Gillight

Aug 27, 2012 | Cars & Trucks

1 Answer

How to reset service reminder alarm on Toyota aurion 2008?


I am not familiar with that model but most Toyotas reset like this. Tune the key off. Pess and hold the odo/trip reset button while you turn the key to the run position (do not start the engine). The odometer should change to all dashes which will disappear one at a time then change to all zeros and then back to the mileage. Release the button as soon as the mileage is displayed. Sometimes the trip A needs to be displayed before you turn off the key to start. Your owners manual should have this info as well.

Aug 07, 2012 | Cars & Trucks

1 Answer

2002 expedition theft light is blinking and car wont start


Thanks for choosing FixYa and welcome. The alarm is causing your car to not start. You need to reset it by entering the code. You should be able to find it by looking in your owner manual. If you can't, you may need to call the dealership to get the code. You will need your VIN number and vehicle info. They may require you to show up in person.

Apr 26, 2011 | 2002 Ford Expedition

1 Answer

I can not reset the alarm module because of that the car wont start so im just lost in this whole car.


Im not sure if this is a factory alarm or aftermarket, try locking and unlocking the pass/side door and see if car starts. if its aftermarket look under the dash for a red button, this is a default button,turn the key on and push this button in four times fast. then try to start the car. hope this helps.

Sep 05, 2010 | 1992 Chrysler New Yorker

3 Answers

THE CAR WONT START AND THE ALARM IS ACTIVATED IS THERE A WAY TO BYPASS OR RESET ALARM


sometimes disconnecting the battery works, also look in your owners manual. sometimes you can turn it off by a sequence in how you push buittons on the radio on your car.

Mar 11, 2010 | 1994 Chrysler LHS

1 Answer

Replaced battery in 99 Jetta and now the alarm goes off when we turn the key. The red light by the door lock stays on. How do we reset the alarm or get it to go off?


u have lost the alarm code when remove the battery .me think is go to electric shop or have a look the alarm book manual if u got it and look in there ,should tell u how to reset the alarm code

Nov 05, 2009 | 1999 Volkswagen New Jetta

1 Answer

What does service system stability mean on my 2001 Cadillac


This refers to the suspension and steering, you probably have a faulty sensor somewhere.
One of the most common sensors to fail in this system is the steering wheel position sensor.
You need to run a diagnostic check to pull the trouble codes to pinpoint the faulty component.

How to pull the codes.....

Use the 3 switches located to the right (LH drive cars) of the Driver Information Center (DIC) to activate and respond to the OBD prompts on the DIC.

ON/OFF = YES
INFO RESET = NO
INFO DOWN or INFO UP = manual toggle


Ignition ON, acknowledge any warning messages;.
Press ON/OFF and INFO UP together for 2 to 3 seconds. Everything in front of you lights up for 4 or 5 seconds, then you will see:

Display shows "ALL?"

Answering YES will display "ALL CODES?"
Answering YES will run automatic test sequence and display codes, if any.

"ALL CLEAR CODES?" will display at the end of the automatic test. If you are satisfied you have the information you need, answer YES to clear/erase all error codes.


Answering "ALL?" with INFO DOWN will toggle systems test manually in order.
Answering "ALL?" with INFO UP will toggle system test manually in reverse order.

Press INFO RESET to reset DIC to "ALL?" to start again.

Ignition OFF to exit.

Write down the codes as they appear on the DIC, you may need to run the check again as it tends to scroll through quickly.

Report back here with the codes.

Sep 21, 2009 | 2001 Cadillac Sts

1 Answer

01 tiburon, alarm reset? wont start


I had the same problem because I store my car in the garage in the winter. I found that replacing the positive/negative cables with new ones and also if you still have your spare key, try putting one key in the ignition and turn to acc before turning it over click your alarm button on your spare set of keys and the alarm should reset itself and the car should start. i hope this helps you, i just finished changing my spark plug wires because I had a code P302 which made my 2nd cylinder misfire, so if your tiburon is around 180,000 km then you should change it too, I recommend Bosch they are the best.
take care
Sven

Mar 19, 2009 | 2001 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...