Question about 2005 Land Rover Range Rover

Open Question

L322 blank screen

The screen on my 2005 L322 shows the Land Rover logo but does nothing else. Also the power button light flases continually

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 105 Answers

SOURCE: range rover l322 power steering not working

check the power steering oil and try to check the cable too


rate this

Posted on Oct 29, 2009

  • 3600 Answers

SOURCE: Replace cv joint rubber boot on front near side,

If the boot is torn it is a good possibility that the shaft may need to be changed. Auto zone and schucks sell aftermarket boots that are called split boots so you don't have to remove the axle. other wise if you buy a new boot you will have to remove the hub cap break the nut loose on the axle then jack up that side and remove the tire remove the brake caliper remove the lower control arm remove the lower ball joint out of the ball joint then force the shaft of the ball joint out of it,s socket pull axle assembly away from the axle and force axle out then remove the old clamps then remove the boot. If it is the outer that's all you need to do if it's the inner boot which some models have then the axle has to be removed from the trans-axle. Be sure to clean the Area where the new boot goes on and clean the U-joint that the boot it covers, when you buy a new boot they should supply you with new grease if they do be sure to pack the grease in the u-joint then install the boot making sure the boot slips into the groove of the axle and slip clamp on and hook it in the spot and bend it forward then bend the tabs over that hold the clamp in place. Be sure where the boot fits it is clean or you will not get it tight enough and it will come off..

Posted on Nov 10, 2009

Testimonial: "Thanks for your help, sounds like i'll be calling Auto Zone or Schuks."

otorres
  • 33 Answers

SOURCE: Hi is there any up date disk for my 54 plate touch

Yes! there it is!
but before you do anything check with the dealer if they work on your system. i heard some people having issues buying updates for their Rovers and they got issues using the software and it was because they were not compatible.

Posted on Dec 01, 2009

Testimonial: "Nice to get some info for free great site "

  • 54 Answers

SOURCE: range rover l322 2002 heavy power steering renewed

The Solenoid fitted on the Steering Rack is not getting the command from The Body Control Unit. Kindly Replace your BCM and then your problem is solved. You can try to make sure by giving direct current of 12v to the solenoid and check the Steering. if it works then simply change the BCM as it's not giving d command to the Solenoid. Salman EiD

Posted on Jul 05, 2010

tunde007
  • 2382 Answers

SOURCE: RANGE ROVER 2004 L322 DRIVER DOOR WONT OPEN FROM

Hi, take the inner door panel off, look around should be a rod that goes from the outside handle to the door latch mechanism, its either broken or unhooked.
This is how i solved a similar problem. When I removed the door panel and looked inside I was able to see the small rod that attaches to the outside handle was not connected. I tried to snap it back in but it wouldn't stay so I pulled the rod over where I could see that the small plastic part on the end of the rod that holds it in place had one side snapped off. Should be easy to fix once I locate the part. Just did this today and haven't looked for the part yet.

Posted on Dec 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Range Rover L322 steering lock ECU Part number and replacement


I have the same issue, has anyone yet managed to find a solution that doesn't involve changing the whole steering column?

Sep 21, 2012 | 2005 Land Rover Range Rover

2 Answers

Range rover l322 2002 heavy power steering renewed


The Solenoid fitted on the Steering Rack is not getting the command from The Body Control Unit. Kindly Replace your BCM and then your problem is solved. You can try to make sure by giving direct current of 12v to the solenoid and check the Steering. if it works then simply change the BCM as it's not giving d command to the Solenoid. Salman EiD

May 15, 2010 | 2005 Land Rover Range Rover

1 Answer

Hi is there any up date disk for my 54 plate touch


Yes! there it is!
but before you do anything check with the dealer if they work on your system. i heard some people having issues buying updates for their Rovers and they got issues using the software and it was because they were not compatible.

Dec 01, 2009 | 2004 Land Rover Range Rover

1 Answer

Range rover l322 power steering not working


check the power steering oil and try to check the cable too


rate this

Oct 29, 2009 | 2005 Land Rover Range Rover

1 Answer

Gearbox crunching in Drive and car will nnot drive


EITHER THE TAIL SHAFT IS FALLING OF OR THE TRANS IS STUFFED

Aug 31, 2009 | 2002 Land Rover Range Rover

Not finding what you are looking for?
2005 Land Rover Range Rover Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...