Question about 1996 Nissan Quest
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
I'm going to send you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.
Posted on Oct 10, 2009
Testimonial: "Finaly I found the air flow door with three screws and removed it. The filter will need replacement soon. It is been replaced one time at the dealer."
1. Open glove box
2. Unhook elastic retainer on right side
3. Locate the two "stop tabs", one on the upper left and the other on the right side. Push both to the left to clear their stops and the glove box will swing down, allowing access to the filter cover.
Posted on May 06, 2009
To change the cabin air filters (there are two, that are in same location), you first have to remove the glovebox. The glovebox itself will not come off. You have to get a phillips head screwdriver to remove the 5 screws. With the glovebox closed, locate the two screws underneath and remove, one on each side. Next open the glovebox, remove the two screws at the top. The fifth screw is on the right behind the plastic molding. Pull back on the top of the lower piece of molding until the bracket pops out. The piece of plastic located just above that piece needs to be pulled out. No need to take it out all the way, just enough to get to the screw. Once removed, with the glovebox open take the fuse panel cover to the right off to allow you better grip. Pull both sides evenly until glove box pops out.
Get a flashlight and shine it on the right side behind where the glovebox was. There is a small plastic cover about 1 inch tall by 5 inches long. It is clipped in place. Push up on the plastic clip with your thumb while pulling out and down with your other finger/fingers. Behind this is one filter. Remove it best you can. Be careful, mine had dead bee's/wasps/dust/dirt/pinestraw/etc. After removing the first, you will notice a second one to the right of that. Slide that one to the left and remove the same way as the first. Look at those filters when you remove and take note the direction of AIR FLOW ^marking. Before replacing with the new ones, vacuum out inside where the filters go as best you can to remove all that crud that fell off of the old filters when removed.
Reinstallation is the reverse of how you removed. I hope this helps all my fellow Pathfinders out there.
Posted on Jun 07, 2009
SOURCE: changing the fuel filter
Starting at the fuel tank.. follow the fuel lines towards the front of the car. Make sure when you replace the fuel filter that you put the arrow on the fiter the right direction, otherwise there will be no flow and the engine will not start,
Posted on Dec 14, 2009
Tips for a great answer:
Jan 13, 2016 | 1996 Nissan Quest
Sep 26, 2013 | 2001 Nissan Quest
Oct 15, 2010 | Nissan Quest Cars & Trucks
Sep 25, 2010 | 1996 Nissan Quest
Jul 27, 2010 | 2005 Nissan Quest
May 31, 2010 | 2005 Nissan Quest
Mar 17, 2010 | 2007 Nissan Quest 3.5 Minivan
Oct 10, 2009 | 2007 Nissan Quest 3.5 Minivan
Nov 20, 2008 | 1998 Nissan Quest
329 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: