Question about 2006 Jeep Wrangler

Open Question

06 wrangler camshaft synchronizer/oil pump drive replacement

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 06 Wrangler...steering pump noise..whines when

when i turn my Jeep (1997) steering left or right pump noise....My mechanic said ,need new pump ?...any one help?

Posted on Dec 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Chirping noise when accelerating


If it is a belt noise, sprinkling baby powder on the belt will make the noise go away. Apply liberaly with engine off onto the belt and start the vehicle. The belt may have gotten coolant on it and this will cause the chirp. Also a defective belt tensioner will cause the belt to chirp

Jan 04, 2016 | 2002 Ford Taurus

2 Answers

I have 1997 Ford explorer 5.0 Replacing camshaft synchronizer It's stuck


Help . Camshaft Sensor - Omfg ( Pics ) - Ford Explorer and Ranger ...

www.explorerforum.com > ... > Stock 1995 - 2001 Explorers
Oct 20, 2010 - 19 posts - ‎7 authors 98 Ford Explorer 2wd 5.0L .... If you're replacing the entire camshaft synchronizer, it gets a little more complicated. ... i would like to only be able to replace the sensor, but if its gonna get ... 1997 xlt v8 awd + 00,XLS .... taking care that the entire shaft comes out of the hole and isn't stuck to the oil pump shaft. Stuck cam position sensor shaft?
2 posts
Nov 24, 2013
Idler pulley squeaking
6 posts
Nov 16, 2012
Easy Camshaft Synchronizer Replacement
8 posts
Sep 11, 2012
Help Diagnose my intermittant Missing Problem
19 posts
May 23, 2004
More results from www.explorerforum.com

Replacing Camshaft Synchronizer & Sensor - Ford Mustang Forum

www.allfordmustangs.com > ... > V6 TecCamshaft Position Synchronizer Replacement - YouTube? 1:16https://www.youtube.com/watch?v=fXOJXnYIZQkNov 18, 2009 - Uploaded by 2003FordTaurus2003 Ford Taurus 3.0L Vulcan 181K miles with chirping sound ... does the shaft move out of its place when ...Camshaft Sensor/Synchronizer Replacement - Page 5 - Ford Tru

Nov 29, 2015 | Ford Cars & Trucks

1 Answer

Ford Taurus 2000 3.0 24 valves tapping oil light stay on like to know if the camshaft synchronize will be able to fix this problem or the oil pump


Low oil level, check the oil. Oil change needed, oil is worn and is not thick as it should be, drain and replace oil/filter. Oil filter clogged, or at last, it could be a weak or faulty oil pump or stripped oil pump driveshaft.

Dec 15, 2013 | 2004 Ford Taurus

1 Answer

Where is the cam sensor at



Description & Operation

2.5L Engines
On the 2.5L 4cylinder engine the Camshaft Position (CMP) sensor is located in the distributor.
The sensor contains a Hall effect device called a sync signal generator to generate a fuel sync signal. This sync signal generator detects a rotating pulse ring (shutter) on the distributor shaft. The pulse ring rotates 180 degrees through the sync signal generator. Its signal is used in conjunction with the Crankshaft Position (CKP) sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinders.
When the leading edge of the pulse ring (shutter) enters the sync signal generator, the following occurs: The interruption of magnetic field causes the voltage to switch high resulting in a sync signal of approximately 5 volts. When the trailing edge of the pulse ring (shutter) leaves the sync signal generator, the following occurs: The change of the magnetic field causes the sync signal voltage to switch low to 0 volts. 4.0L

The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter.
The CMP sensor contains a Hall effect device called a sync signal generator to generate a fuel sync signal. This sync signal generator detects a rotating pulse ring (shutter) on the oil pump drive shaft. The pulse ring rotates 180 degrees through the sync signal generator. Its signal is used in conjunction with the crankshaft position sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinders.
When the leading edge of the pulse ring (shutter) enters the sync signal generator, the following occurs: The interruption of magnetic field causes the voltage to switch high resulting in a sync signal of approximately 5 volts.
When the trailing edge of th4.7L

The Camshaft Position Sensor (CMP) on the 4.7L V8 engine is bolted to the front/top of the right cylinder head.
The CMP sensor contains a Hall effect device called a sync signal generator to generate a fuel sync signal. This sync signal generator detects notches located on a tone wheel. The tone wheel is located at the front of the camshaft for the right cylinder head. As the tone wheel rotates, the notches pass through the sync signal generator. The pattern of the notches (viewed counter-clockwise from front of engine) is: 1 notch, 2 notches, 3 notches, 3 notches, 2 notches 1 notch, 3 notches and 1 notch. The signal from 5.7L V8 Engines

The Camshaft Position Sensor (CMP) on the 5.7L V-8 engine is located below the generator on the timing chain / case cover on the right/front side of engine.

0996b43f80202435.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig.

The CMP sensor is used in conjunction with the crankshaft position sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinders. The sensor generates electrical pulses. These pulses (signals) are sent to the Powertrain Control Module (PCM). The PCM will then determine crankshaft position from both the camshaft position sensor and crankshaft position sensor.
The tone wheel is located at the front of the camshaft (2). As the tone wheel rotates, notches (3) pass through the sync signal generator.
When the cam gear is rotating, the sensor will detect the notches. Input voltage from the sensor to the PCM will then switch from a low (approximately 0.3 volts) to a high (approximately 5 volts). When the sensor detects a notch has passed, the input voltage switches back low to approximately 0.3 voltsthe CMP sensor is used in conjunction with the crankshaft position sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinderse pulse ring (shutter) leaves the sync signal generator, the following occurs: The change of the magnetic field causes the sync signal voltage to switch low to 0 volts

Jun 08, 2012 | 1999 Jeep Grand Cherokee

1 Answer

Where is the camshaft position senor on a 2000 jeep grand cherokee 4 liter


4.0L
The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter.
The CMP sensor contains a Hall effect device called a sync signal generator to generate a fuel sync signal. This sync signal generator detects a rotating pulse ring (shutter) on the oil pump drive shaft. The pulse ring rotates 180 degrees through the sync signal generator. Its signal is used in conjunction with the crankshaft position sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinders.
When the leading edge of the pulse ring (shutter) enters the sync signal generator, the following occurs: The interruption of magnetic field causes the voltage to switch high resulting in a sync signal of approximately 5 volts.
When the trailing edge of the pulse ring (shutter) leaves the sync signal generator, the following occurs: The change of the magnetic field causes the sync signal voltage to switch low to 0 volts


This information is available from the Autozone.com websitecheap_repair_3.jpg

Jan 27, 2011 | 2000 Jeep Grand Cherokee

1 Answer

What drives the oil pump on a 4.3L V6?


the camshaft drives the distributor gear at the bottom of the distributor and in the bottom of the distributor gear is a slot which fits onto the oil pump drive shaft common problem is the cam gear is made of plastic and the teeth break off and clog the oil pump screen if the gears are replaced and the oil pump is not replaced or cleaned failure will result

Aug 28, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

My car is not pumping oil a 1997 Ford Taurus I replaced the oil pump


Im guessing you need to replace the gear on the camshaft position sensor! it also drives the oil pump. its a common failure its made of plastic or fiber. im sure you also have a camshaft position sensor code. replace that gear and hopefully your motor is ok! good luck!

Mar 05, 2010 | 2005 Ford Taurus

2 Answers

How do I replace the serpentine belt on my 2000 Plymouth Breeze 2.4l engine?


the tensioner is on the alternator there is usually a cover over it you need to loosen the 2 screws on the alternator and turn the "adjuster" screw till the belt is loose enough to come off note the whay it is run then install and tighten the new belt it must be very tight or it will slip

Sep 14, 2009 | Plymouth Breeze Cars & Trucks

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...


The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

2 Answers

1998 FORD 4WD RANGER 128,000 MILES ENGINE LOST OIL PRESSURE OIL PUMP LOOKS GOOD NO SLUG IN OIL PAN, WHY?


Most likely your oil pressure relief valve located on in or nearby pump. Symptoms are oil pressure will drop when warmed up when idle lose all pressure eraticly giving the vehicle gas will bring back pressure and highway driving will bring pressure up until idle again.

Jul 18, 2008 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
2006 Jeep Wrangler Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...