Question about 2001 Dodge Dakota

Open Question

Need to bleed clutch on 2001 dodge dakota

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimbopickens
  • 56 Answers

SOURCE: dodge dakota 2001 has no headlights, running, dome or turn lighs

Have your alternator checked...

Posted on Nov 22, 2008

  • 840 Answers

SOURCE: How to replace power window motor on 2001 dakota

its not hard guys Take the door trim panel by taking off screws and mirror cover / pull out bottom of door and then sides pull up and outthen take off vapor barrier then look inside of door put tape on glass to hold it up take out bolts on the regulator and exchange it Please rate my response thank you very much

Posted on Feb 02, 2009

  • 1 Answer

SOURCE: 2001 dodge dakota crank no start

Just had that problem w/ my 01 Dekota, it was the resistor that used to be mounted on the firewall and easy to get to but that is now mounted low on the back of the engine jammed into a bey tight position. I couldn't get to it myself, so ended up taking it to neighborhood garage. Cost me about $150

Posted on Apr 16, 2009

rockitman187
  • 2559 Answers

SOURCE: clutch goes to floor will not engage

Bleeding won't fix it,If it can be put in gear and car doesn't move your clutch is no good.

Posted on May 28, 2009

roniecon
  • 6826 Answers

SOURCE: 2001 dodge dakota lights flicker

check for battery short inside battery have some one check for ac voltage in battery and alternator out put,,,headlight switch would be next to check or replace

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced throw out bearings on 1996 dodge Dakota/ v6,do i bleed clutch also,if so how.


if the slave cylinder remaine intact on the hose from the master cylinder then there is no need to bleed the system
if the slave cylinder was inside the bell housing and you ahd to remove a hose to get the box out then yes it has to be bled and by the bleed niple on the sode of the bell housding
bleeding procedure is as per any hydraulic system

Jul 07, 2015 | Dodge Cars & Trucks

1 Answer

2001 dodge dakota sport with 2.5 engine idles high when I start it up, continues idling high, when pushing clutch in to change gears it idles extremely high


Does it do it if you disconnect the idle air control valve ?
You need to know if its a vac leak or if the computer is making the valve open too far.

Feb 09, 2014 | 2001 Dodge Dakota

1 Answer

Truck blew upper radiator hose changed that and thermostat still over heating think its air bound any way to bleed 2001 dodge dakota


remove the radiator cap, leave it in park, start up and let it idle. turn on the heater so the air gets out of the heater core. give it 15 or 20 min. after it reaches operating temperature. if needed, do it again. also remember your thermostat may be bad

Apr 16, 2011 | 2001 Dodge Dakota

1 Answer

Bleeding Clutch Cylinder with no bleeder screw


I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Jun 04, 2009 | 1996 Honda Accord

1 Answer

How do I bleed the clutch slave cylinder on a 1993 Dodge Dakota Sport 2wd?


should be self bleeding if pedal is set correct

pedal rod needs 1/8" free play to clutch master clydinder plunger

fill clutch res slowly let bubbles bleed

then only half strokes on the clutch pedal with 30sec pause between pumps

Mar 19, 2009 | 1993 Dodge Dakota

1 Answer

Dodge dakota 87


Hi, Just a thought, is the clutch drive plate in the right way round?
Press the Blue Button please if sorted!
Paul 'W' U.K.

Feb 08, 2009 | 1995 Dodge Dakota

2 Answers

Dodge dakota


i have a 2000 dodge dakot and can not bleed the slave cly how do i do it

Jan 29, 2009 | 1995 Dodge Dakota

Not finding what you are looking for?
2001 Dodge Dakota Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...