2004 Buick LeSabre Logo

Related Topics:

A
Anonymous Posted on Oct 27, 2012

How to install a ignition module on 2004 buick lesabre

5 Related Answers

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Nov 06, 2008

SOURCE: 2000 Buick LeSabre ingintion coil and module

The coil is on top of the engine and the module on the firewall or suspension strut tower

Ad
daves944

Dave C

  • 1050 Answers
  • Posted on Apr 05, 2009

SOURCE: 1998 BUICK LESABRE CUTS OFF WHILE DRIVING

The problem is the crankshaft sensor for sure. It is mounted behind the crankshaft pulley which is pretty difficult to get off as you need a special puller. A shop should charge about 1.5 hours for this job. It is a very common problem.

Anonymous

  • 1 Answer
  • Posted on Jul 23, 2009

SOURCE: REPLACEMENT OF [LOW BEAM] HALOGEN BULB IN 2004 Buick LeSabre

I just Replaced a Low Beam Light bulb on a 2005 Buick La Sabre.

If You use a Metric socket and Remove the Two Silver bolts Attaching the headlight Assemble onto the metal surrounding the the lamp assembly it comes out to the front. This makes it much easier to access the bulb. Twist it counerclockwise & it comes out by pulling gently on the bulb. Then by realeasing a tab that is the socket holder bulb can be removed & replaced with a New #9006 low beam halogen light bulb. Wrap a Paper towel around the bulb & do NOT touch it with your bare hand as this wiil ruin a halogen bulb,

Anonymous

  • 1 Answer
  • Posted on Aug 02, 2009

SOURCE: need instructions for replacing 94 Buick LeSabre window module.

2002 BUICK LESABRE REAR DRIVER SIDE DOOR POWER WINDOW UP CABLE IS OFF TRACK WINDOW WILL NOT STAY UP HOW CAN I REPAIR THAT

honeymokey

honeymokey

  • 3113 Answers
  • Posted on Oct 09, 2009

SOURCE: 2004 Buick Lesabre speedometer not working

Yes it's on the right side othe transmission just above the passenger side cv axle. You most likley need to send the cluster off and have it checked. Model Electronics in NY.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
1answer

Where is the Body Control Module (BCM) on a 2000 buick lesabre

It's not the BCM. The BCM doesn't affect the ignition switch power. But the ignition switch will affect the BCM. I would look to see why you don't have power to the ignition switch first. Fuse or wire.
0helpful
1answer

How to install a ignition module buick lesabre V6 3800

1A Auto shows you how to remove, install, repair, or replace your broken misfiring or damaged ignition coil. This video is applicable to Buick LeSabre 2000-2005.
3helpful
2answers

Where is the ignition control module located on a 1990 buick lesabre

For 1990 Buick Lesabre 3.8L FI OHV 6cyl the Control Module-Ignition is located: Under hood, passenger side, front engine area, mounted on upper passenger side of cylinder head under ignition coil.

Hope helps (remember to rate this answer).
1helpful
2answers

I need to replace ny 1995 buick lesabre ignition control module ...

the ignition control module is mounted to the left cylinder head. more precicely, under the 3 coils
0helpful
1answer
7helpful
1answer

Blower motor replacement

Very easy!!!

Here ya go!!!

Removal & Installation
  1. Remove the right side sound insulator in the passenger compartment.
  2. Disconnect the electrical connector from the blower motor.
  3. Disconnect the blower ventilation tube from the module.
  4. Remove the blower motor screws.
  5. Remove the blower motor from the housing.
  6. Install the blower motor into the housing.
To install:
  1. Install the blower motor screws and tighten to 15 inch lbs. (1.5 Nm).
  2. Install the blower ventilation tube to the module.
  3. Connect the blower motor electrical connector.
  4. Install the right side sound insulator.
0helpful
1answer
2helpful
1answer

Installing ignition module

Unscrew the ignition coil(s) from on top of the module...(leave plug wires attached)....and set aside noting coil position on module....unplug module and replace with a known working module.If there is grease under old module...transfer it to new module.Replace coil(s) and start her up.
TIP. While you are there,why not also change the crank sensor (if it not new).....it is THE trouble maker on these engines.
0helpful
1answer

Location for electronic spark control module 1994 buick lesabre 3800

Technically it is called a "SPAR" Control Module" some folks call it ECM even an "Ignition Control Module" when asking for the new part a new guy will have troble finding by the more common names.... of course nothing beats experience(wink)
1helpful
1answer

2000 Buick LeSabre ingintion coil and module

The coil is on top of the engine and the module on the firewall or suspension strut tower
Not finding what you are looking for?

290 views

Ask a Question

Usually answered in minutes!

Top Buick Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...