Question about 2004 Nissan Murano

Open Question

05 NISSAN MURANO WINDSHIELD WASHER TANK REMOVAL

WASHER PUMP NOT WORKING. HOW DO I GET AT BOLTS TO REMOVE TANK ??

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: how to remove the tail lights from a 2003 murano

Here's the step by step procedure from the beginning.

  1. Carefully remove the black one inch wide plastic molding strip that runs along the interior side of the tail light. This can be pried off carefully without breaking the plastic clips that hold it in place.
  2. Using a 10mm socket, remove the two bolts that you see which secure the tail light housing.
  3. The tail light housing is also held in place with three or four plastic clips which can be broken rather easily if you don't do this next step carefully. Begin prying the plastic tail light using a plastic putty knife or screwdriver. The top clip comes out pretty easily and so does the bottom one.
  4. On a cold winter day, the middle clip is the one that can break rather easily so gently rock the tail light or wait for warm weather when the plastic isn't brittle.
  5. Once the tail light "bucket" is removed it's a simple matter to replace the bulbs.
d87baef.jpg

Posted on Jan 03, 2009

MrScary66613
  • 1990 Answers

SOURCE: 05 Murano 2WD Replace serpentine belts??

That is Exactly Correct. Draw the Diagram of the Belt Before you remove it so that you can get it Back on the Correct way. Please Rate My Response! Thanks!

Posted on Feb 01, 2009

  • 1 Answer

SOURCE: '06 Nissan Murano factory radio/cd player removal steps

what holds the radio in place besides the 2 side screws in a 2006 nissan murano

Posted on Feb 08, 2009

  • 1 Answer

SOURCE: remove windshield washer reservoir

Take off the wheel well shroud. Firdt remove the front right wheel, it will be easier. Then remove the two screws holding in the tank. Remove the two electrical connectons and small rubber hose. Next (or first) grab the filler tube and twist while pulling it from the tank as it is held in by a rubber gromet. Then pull the tank forward and let it drop down. Nothing else is holding it in except the two screws. Removing the filler tube is a must!

Posted on Apr 21, 2009

  • 1 Answer

SOURCE: How to Remove Car Radio from Nissan Murano

If you disconnect one of the battery cables for about 30 sec and reconnect it, that will reset the CD player. Then you can put in the key and see if can eject the offending CD. My bet is that it won't. I own a 2006 with a failing CD (getting it replaced on warranty next week). The CD player in these cars is a real stinker. Nissan should be ashamed.

Posted on Oct 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out
The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.
  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.

Apr 07, 2015 | Ford Cars & Trucks

2 Answers

How do you remove a windshield washer reservoir on a 1995 Tahoe 350 5.7
Do you think this would work?

http://www.ehow.com/how_5189121_change-tahoe-washer-fluid-tank.html

Feb 27, 2015 | 1995 Chevrolet Tahoe

1 Answer

Front windshield washer is not pumping to spray windows need to replace unsure how to get to it Sante Fe 2004
I presume you've check the fluid level in the washer resevior? This particular problem is common. The inlet opening to the pump is clogged by slime. We usually 'unclog' the obstruction using compressed air. The resevior (tank) needs to be removed and flushed/cleaned out. It can be accessed under the RH wheel well liner. There are 2 10mm bolts fastening the tank to the vehicle. remove those bolts. Then disconnect the hoses (one for front, the other for rear wiper/wash). Disconnect the electrical connector to the pump. You can now remove the resevior (tank) from the vehicle and flush/clean it.

Jun 29, 2011 | Hyundai Santa Fe Cars & Trucks

1 Answer

I need to know how to replace the spark plugs of my murano 2004? the 3 at the front are not the problem, the ones i want to know how to do it are the ones on the back,. thanks
you need to remove the upper half of the intake plenum to acces the plugs.not as bad as it looks.only tricky part is the support bracket bolts(12mm) on rear of plenum.if you remove the lower windshield cowling and metal cowl panel at base of windshield it makes it much easier.may seem intimidating but its actually very straight forward and only takes about an hour start to finish.any further questions let me know.good luck!

May 15, 2011 | 2004 Nissan Murano

1 Answer

Windshield washer does not work; no sound coming from the motor/pump. where is the fuse for the windshield washer motor/pump?
check wiring to pump with test light see if hot first, If not find fuse in owners Manuel, if its hot need a pump, they do go bad

Mar 15, 2011 | 2004 Nissan Murano

1 Answer

05 neon windshield washer tank is full but not spraying fluid. I assume the pump is shot. Any advice on replacing the motor/pump. I would like to do this myself if not to involved.
its a simple job but first buy the pump and you will see where the bolts/screws go then you will be able to remove same on car and fit new.before buying though,try removing a hose from the pump and get someone to operate the switch,might just be s..t in the pipe.

Aug 20, 2010 | 2005 Dodge Neon

2 Answers

WHERE DO i FILL WIPER FLUID IN REAR FOR 2006 NISSAN MURANO?
The fluid for both windows comes from the front resivoir. The pump there is suited to pump either to the front or to the rear based upon your operation of the switch & if the rear isn't working, the line will need to be removed near the pump & checked for obstructions.

These can be cleaned with a vacuum tester, the kind that lets you pump the unit & draw a vacuum, connected to the hose, it will draw any debris back out of the tube. You probably don't want to try & force fluid through the hose as it won't fit through the washer nozzle.

good luck

Jan 20, 2010 | 2006 Nissan Murano

1 Answer

Mercury villager 1994 washer pump not working
the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Fog light bulb replacement
This bulb can be replaced without removing the washer fluid reservoir. There are 3 screws that go through the bottom edge of the bumper cover into the right inner fender guard. Remove these screws and pull the inner fender down to gain access to the back side of the fog lamp and remove the bulb.


Nissan Scope Technician- 10+ years experience in Nissan dealership.

Nov 04, 2008 | 2003 Nissan Murano

1 Answer

Replace the windshield washer motor
first locate the washer tank, remove the bolts that are holding it. remove the wire to the motor, remove the hose that is attached to the motor, slowly pull the motor off the rubber gasket .

do the reverse in installing a new one.

tnx 4 using fixya,

drcool


Aug 07, 2008 | 1997 Toyota Camry

Not finding what you are looking for?

View Most Popular

2004 Murano

  • Cars & Trucks

Related Question

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out

  • Ford Cars & Trucks

Open Questions:

0 Answers

Nissan 2004 Murano gearbox internal parts split schematic

Jan 16, 2017 | 2004 Nissan Murano

0 Answers

Where is voltage regulator fuse 3 located? battery not staying charged

Oct 27, 2015 | 2004 Nissan Murano

0 Answers

my murano 2004 has problem of starting,when itook to an engineer he change the both two top cylinder,now the car can start but when you throttle it' it can amswer..imeant the car is not accelerating if u throttle.,please what is the cause of that?

Mar 07, 2015 | 2004 Nissan Murano

0 Answers

I have a Nissan Murano 2004 model that loses accelleration completely while driving.

Feb 21, 2015 | 2004 Nissan Murano

See all 2004 Nissan Murano Questions

2004 Nissan Murano Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2005 Nissan Murano

2007 Nissan Murano SE

2005 Nissan Murano

2006 Nissan Murano

2003 Nissan Murano

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
2004-Nissan-Murano.pdf....

2004 Murano

PDF Manual
. 2004 Murano Manual

2004 Murano

Loading...