Question about Cars & Trucks

Open Question

I need info to help me install a Dorman 74300 Rear Driver Side Replacement Interior Cargo Door Handle

I need installation instructions for a Dorman 74300 Rear Driver Side Replacement Interior Cargo Door Handle

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 120 Answers

SOURCE: 1999 toyota corrolla interior door handle replacement

take the screw out then slide it foward to relase the clips be hind the handle

Posted on Feb 14, 2009

Ad
greezy_je208
  • 237 Answers

SOURCE: installing driver side interior door handle

pull the inner panel off by first un screwing the two screws located on the handle portion of the panel(they may have plastic hadeaway covers over the heads) then remove the window rolldown handle(if so equipped,manual window)then pull the plastic trangle from the inner of the mirror(this little tri angle keeps the trim down and secure on the door. then pull the palnel directly out there are small clasp pins in behind the panel try not to break these(but they do sell replacements at your local auto store) you will have to get ALL of these free then wiggle the panel up releasing it from the inner shell of the door and and window. you should now have a clean view of the handle. you will now need to droll out the rivit holding the handle to the inner steel of the door. pull the handle forward and it should be released from the inner steel now there clips holding the "rods" to the handles back side, they should have a little piece clipped to the rodto un clip these you need only push them off with your thumb. then replace handle with the new one, and uce a large steel screw to secure the handle when replacing back on door.

Posted on Dec 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace inside door handle passenger side on a 2011 GMC Terrain?


Search Results

    How To Install Replace Inside Door Handle Chevy Equinox ...

    ? 9:02
    https://www.youtube.com/watch?v=cY6asyM2R6g
    Feb 2, 2012 - Uploaded by 1A Auto Parts
    How To Install Replace Inside Door Handle Chevy Equinox 05-09 1AAuto.com .... found your tutorial on fixing my driver's side door handle for my 2006 Equinox. .... Door Handles Chevy Equinox 2010 2011 2012 GMC Terrain ...

    How To Install Replace Inside Door Handle 2007-13 ...

    ? 9:05
    https://www.youtube.com/watch?v=QonKLwhk2CE
    Apr 2, 2015 - Uploaded by 1A Auto Parts
    http://www.1aauto.com/interior-door-handle-driver-side-front/i/1adhi00417 1A Auto shows you how to repair, install, fix,change or replace a broken or snappe... ... 10, 11, 12, 13 Chevy Silverado, Tahoe, Suburban and GMC Sierra, Yukon Denali ...2007-2011 Tahoe Yukon Suburban Escalade Vent Section ...Missing: terrain

    How To Install Remove Rear Outside Door Handle 2007-13 ...

    ? 10:02
    https://www.youtube.com/watch?v=7ZUTqqEzpZg



Feb 08, 2016 | GMC Cars & Trucks

Tip

Door handle repair for Ford fusion


The door handle will not allow unlocking from the inside. This is a common problem with the Ford Fusion 2007 to 2012 and other cars. A cheap piece of plastic breaks that connects the lock lever with the door handle. You can roll down the window and unlock from the outside or hold both levers together and pull open from the inside. This is a very simple repair. Go to any of many web sites for auto parts and buy a replacement. I bought a Dorman 81702 Ford/Lincoln/Mercury Interior Front Driver Side Replacement Door Handle. I popped off the lid that covers a hidden screw inside the recess of the door handle. You have to use a torque bit to unscrew the screw. I then unscrewed the torque screw holding the upper part of the door panel that is opposite the door hinge. The upper part of the door panel can be be carefully pulled away with moderate pressure allowing access to the door handle mechanism. One more bolt holds the door handle part in place. Pull out the broken door handle part, remove the locking cable and put in the new part. Reverse the process to finish up. The whole process took about 10 minutes.

on Sep 18, 2015 | 2010 Ford Fusion Hybrid

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

I have owned a 1994 and a now a 2001 chevy blazer and on both suv's the drivers door spring and i think its called a hinge pin on the interior part of the door where the latch connects to the door...


Yes it is very common, the driver side door is the one most used and the factory parts cannot handle it. I have had many break on me if not seperate completely from the door. The best thing to do is go to your local parts store and get a Dorman replacement for them.
Good Luck!

May 11, 2011 | 2001 Chevrolet Blazer

2 Answers

Replace inside door handle drivers side


Here is a replacement part: http://www.amazon.com/Dorman-79548-Tribute-Interior-Replacement/dp/B0031GJYZW
To install the new one, remove the plastic door panel by removing the philips screws and clips that hold it in place. You should be able to pull it straight up and out. Don't put too much force on the panel, the plastic is cheap. The interior door handle should now be able to be unscrewed and replaced.

Mar 07, 2011 | 2001 Mazda Tribute

1 Answer

Replacing driver side door handle


First, ya gotta remove the interior door panel....

Door Panel
  1. Fully lower the door glass.
  2. Remove the arm rest, door lock knob and inside door handle escutcheon.
  3. Remove the regulator handle.
  4. Gently pry the door panel away from the door.
  5. Installation is the reverse of removal. Install the regulator handle (correct position) with the door glass closed.
Next you'll need a small ratchet and extenstion with socket...or a socket driver (like a screwdriver but holds a socket). Remove the two nuts attaching the handle to the door. Use a long thin flat screwdriver and pop loose the clip attaching the rod to the lock mechanism..
Manuever the handle off the door and then install in reverse order.

May 28, 2010 | 1987 Nissan Pickup

1 Answer

I need to replace LR (driver side) exterior door handle assembly on my Honda Odyssey 2000. I found a source for part but need replacement instruction. Can you help? Thanks, Ed


Have to take off inner door panel and all parts then u will gain access to inside of door remove all linkages and remove bolts from door handle and install in reverse order.

Oct 20, 2009 | 2000 Honda Odyssey

1 Answer

Installing replacement side mirror on 2007 Subaru Forester


yes... you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can access the bolts holding the mirror on and disconnect the wiring harness as well..

Aug 20, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

3 Answers

1997 buick park ave 4 door right front door handle won,t work from the outside


Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.

Jul 06, 2009 | 1997 Buick Park Avenue

2 Answers

Driver side interior door handle


Replace it with the rear doors handle till you can buy one for the rear door. thats what i did.

Oct 03, 2008 | 2001 Chevrolet Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...