Question about Cars & Trucks

Open Question

Installing vn commodore ute door handles

How do i install vn ute exterior door handles

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 43 Answers

SOURCE: Need to know how to install exterior door handles

I'm assuming that you have the coupe not convertible since I've had same problem with my 97 Dodge Avenger and this is quite common from what I have heard. The handle is held in place by two 10mm bolts. One is easily accessable, located right beside the handle with the door open. The other is a little harder to get at. The first thing you need to do is remove the inside door cover, held in place by four screws and push in clips along the bottom that pull out easily. Two of the screws are visible and in the top corners of the door panel. One screw is located behind the inside handle and once removed the moulding comes off quite easily. The other screw is in the hand hold where you pull the door closed and has a small plastic cover over it. If you have power windows you are able to disconnect the switches once the panel is off. If manual windows, the handles are usually held on by a clip that can be pushed off with a screw driver allowing you to pull of the crank handle. The window needs to be in the closed position so you can access the ONE 10mm bolt holding the outer door handle. Once the interior door panel is off, if any clips remain in the door, take them out and put them where they should be in the door cover it won't go back together properly if you don't. Now you'll need to pull down the corner of the plastic covering the door, don't remove all the plastic just enough to allow access to the bolt. I used a small rachet to get it out. It is in a stupid spot with not much room but is doable. Once out, the handle is only being held by the lock rods to the handle and lock cylinder. The lock cylinder is held by a retaining clip which can be slid off allowing the cylinder to be pushed out. The other rod connected to the handle has a plastic clip on it holding it in place. This can be opened with a small screwdriver. Once opened the rod will come out easily and the handle should come off the door. The only problem reinstalling, that I had, was reconnecting the rod to the handle and found that if you unscrew the door latch, the whole mechanism can be moved down, giving you more freedom to work with the rod. You might want to do this before fighting with the clip holding the rod in place, just a thought as I got mine apart in 20 min. Installing the new handle is quite easy, just attach rod to the handle FIRST before anything else. Once the handle is back on the door the lock cylinder can be pushed back in, it just gets in the way if you put it in the handle right away. Hope this is of some help.

Posted on Oct 05, 2008

motor1258
  • 6674 Answers

SOURCE: 1999 Chevrolet silverado exterior door handle replacement

Got to remove inside panel & remove nuts holding it on.

Posted on Dec 13, 2008

  • 508 Answers

SOURCE: How to replace '96 Ford Explorer driver side exterior door handle

You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Posted on Feb 18, 2009

wireguy212
  • 1627 Answers

SOURCE: replacement exterior door handle

you will need to get the door panel off the inside,undo the linkages and the remove the nuts holding the handle on.

Posted on Jul 28, 2009

  • 1986 Answers

SOURCE: door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to intall new front exterior drivers side door handle on a 2002 Hyundai Elantra GLS


remove the interior door trim and you will see small nuts holding the handle onto the outer door skin. Remove any rods /clips and undo the nuts and the handle will come out.

Mar 18, 2014 | Hyundai Motor 2002 Elantra

1 Answer

Radiater fluid coming from behaind balancer Model V6 VS Commodore New Radiater instaled and not coming from there any Ideas???


check your entire cooling system for leaks including water pump, thermostat, radiator hoses, even your coolant reservoir. leaks are rough man sorry for your frustration.

Mar 27, 2012 | Holden Ute Cars & Trucks

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

VZ 2005 ute central locking works well from the


is it a factory or aftermarket security system?

Apr 28, 2010 | 2008 GMC Savana Cargo

1 Answer

Ford expedition side mirror (instalation giude)


SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.
  1. Remove the door handle bezel.
    • Use service notch.
  1. Remove the window control switch plate.
    • Use service notch and disconnect the electrical connectors.
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    Remove the two bolts and three screws, and remove the door trim panel.
  1. Remove the weather shield.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror.
    • Remove the nuts.
cf86471.gif
  1. To install, reverse the removal procedure.
    • Install top nut first.
---
Exterior Mirror Motor Removal and Installation
  1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.
  1. Disconnect the heated mirror electrical connectors.
  1. Remove the exterior mirror motor screws and exterior mirror motor.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.

Oct 26, 2009 | 2003 Ford Expedition

1 Answer

Replace left front door outside handle pot metal tip broke off


SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Exterior Front Door Handle Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. NOTE: The tie strap does not need to be reinstalled.
    If equipped, remove the tie strap from the anti-theft guard.
  1. Remove the screws and position the anti-theft guard aside.
  1. Release the clip and disconnect the exterior door handle actuating rod.
88661dd.gif
  1. Remove the anti-theft guard.
  1. Remove the exterior door handle screw.
  1. Remove the exterior handle actuating rod.
  1. Remove the exterior door handle lock cylinder cover.
  1. Remove the exterior door handle.

Apr 25, 2009 | 2001 Ford Escape

1 Answer

How to install exterior door handle on 95 Safari Van


hi, remove the entire door interior panel, keep notes and diagrams as you go, even take pics, usually the exterior handle is secured by 2 small screws or nuts, undo these and the handle will detach . there will be a small rod connected to this handle by a small clip or similar. reassembly is a reversal of the entire process, just take your time

Feb 11, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Diagram for replacing exterior door handles


ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

Dec 14, 2008 | 1997 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...