Question about 1988 Chevrolet C1500

Open Question

HOW TO BLEED SLAVE CYLINDER IN 1988 CHEVY PICKUP

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Replaced slave cylinder on 1988 Chevy truck dosen't work.

try to do this http://www.youtube.com/watch?v=uj1dMdYgRK4 this might work for you let me know if it does

Posted on Apr 09, 2009

protek480
  • 1714 Answers

SOURCE: 1997 Chevy 1500 pickup 2wd

One of the wheel cylinders is leaking, pulling air back into brake system and it's going back to the4 master cylinder. Look for brake fluid leaking at one of the wheel cylinders, that's where the problem is.

Posted on Oct 10, 2009

Testimonial: "The problem was resolved through other means"

  • 157 Answers

SOURCE: Clutch pedal does not disengage clutch

If the car hasn't been driven for a while it could be corrosion on the fork but I think that is unlikely. I think you are right about the release bearing being jammed in the spring. If the truck has quite high mileage, it probably means a clutch job.

Posted on Feb 27, 2010

jonathanh356
  • 75 Answers

SOURCE: I have a 92 chevy 1/2 ton 4x4 and i cant get the

I keep a Holley Black Electric fuel pump around for just such occasions. If you happen to have an in-line pump layin around just hook it up and let her rip. Always works for me.

Posted on May 30, 2010

  • 376 Answers

SOURCE: how to bleed hydraulic slave/master

Bleeding the slave cylinder is done just like bleeding your brake system.Just be sure that you keep enough fluid in the master cylinder so that you don't have to do it all over.Also make sure you have a steady stream of fluid.as you would with your brakes.

Posted on Mar 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed master clutch cylinder on a 1988 chevy s10


Bleed master first and then slave get tube on bleed nipple and keep pumping into bottle keeping tube in fluid in bottle so it will not draw air on return stroke some cars can be quite hard too bleed

Nov 18, 2015 | Cars & Trucks

1 Answer

Hello i have a 1993 chevy cheyyenne k1500 pickup with a v6 4.3 its a manual and my clutch line broke off of my slabe cylinder due to a crack in it from ware and tear which leaked fluid all out and lost...


I changed the slave cylinder on my 97 Accord and all I did was disconnect the lines, disconnect the linkage from the pedal, move some stuff to get it out, hook up the new one, fill with fluid, and bleed the line to the clutch cylinder. Point is, if you have to remove the slave cylinder, that's fine. You'll have to bleed the system anyway. Like bleeding brakes. I didn't have to drain any "tranny fluid" as the clutch fluid was a separate system. Had a drain pan underneath to catch fluid.

May 30, 2017 | Chevrolet Cars & Trucks

1 Answer

Working on 1988 chevy Scottsdale the clutch line got a leak so I changed it and tried to bleed and nothkng. I checked to see if master cylinder was pumping and had to replace also. Dealer said he replaced...


If you can get a hand operated vacuum pump and seal it in place of the cap on the master cylinder apply vacuum and you will see the air bubbles being removed from the slave cylinder. It has always worked for me.

Aug 17, 2013 | Cars & Trucks

1 Answer

The clutch will not engage properly on my 1988 toyota pickup. Already replace clutch master cyclinder and clutch slave?


There are a couple of possibilities; worn clutch plate, failed pressure plate, possible hanging up of the throw-out bearing. Also, some hydraulic clutches have a throw adjustment on the slave cylinder that may need adjustment after replacing the slave cylinder.
If you plan on more DIY maintenance, I would highly recommend buying a Haynes service manual, you'll find the $25 well-spent:
Toyota pickup manual

Mar 31, 2011 | 1988 Toyota Pickup

1 Answer

No cluch no fluid.Is there a place to bleed it.after adding fluid


yes a slave cylinder at gearbox should be a bleed nipple on it

Feb 15, 2011 | 1988 Toyota Pickup

1 Answer

How do you drain the clutch fluid reservoir on a 1988 Ford F150 pickup?


You don't, per se, drain it. First, locate the air bleeder screw on the slave cylinder and crack it loose, then snug it back down just enough to not leak.

Then, with a helper, bleed the old fluid out and add new fluid as the level in the master cylinder goes down.

When you have clean fluid coming thru the bleeder screw, make sure there isn't any air in the system and tighten the bleeder screw.

Make sure, as you perform the bleeding process to not let the cylinder run out of fluid.

Jan 16, 2011 | 1988 Ford F 150

1 Answer

I need help changing out the master cylinder in my '94 toyota 4x4 pickup truck. It is a 5speed, i have already changed out the slave cylinder and installed the master cylinder but i still can not get the...


did you bleed the system?? you must bleed the system from the clutch slave. if this has been done, I need more info!! How does the clutch pedal feel, is the clutch slave engaging at all??

Sep 27, 2010 | 1994 Toyota Pickup

2 Answers

Wont shift into gear


Was the fluid low? Does the pedal have any resistance? does it feel normal? Did it happen all of a sudden? Does it shift into gear with the engine off? You say it doesnt shift into gear, but does the shifter move into gear or not? Or it does and the truck wont move? Sounds like maybe the SLAVE CYL isnt operating? leaking? theres more questions to answer.

Dec 30, 2009 | 1988 Toyota Pickup

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

2 Answers

Clutch problem


Open bleeder at slave. Push down on pedal and hold. Tighten bleeder and repeat until fluid is present. Then pump up and bleed remainder of air. Requires two people.

Mar 29, 2009 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...