Question about 1984 GMC VanDura

Open Question

How to replace a heater core in a 1995 gmc vandura van 2500

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: NEED TO REMOVE DASH TO

yes you have to remove the whole dash assambly to replace the heater core..have fun i had to do mine twice.my new heater core lasted about 6 months.

Posted on Mar 30, 2009

dnewcombe1
  • 1564 Answers

SOURCE: Replacing heater core in 2000 GMC sonoma. Dash is

If the dash is removed you've saved about 9 10ths of the job endurance. Look around, what you believe to be, the perimeter of the heater box. I cannot, and no one else can, tell you exactly where the bolts and nuts that mount the heater box are. Therefore you must viually sixe the box and check outide in the engine compartment and inside under the dash for the mounting bolts.You'll want to start by removing the heater hoses. Then starting at the passenger side engine compartment look for a group of 10mm or 7/16ths nuts retaining the housing and remove them. Do the same inside. The housing is usually held together with screws or clips, it changes year to year. Keep a log or pix of the wires and cables and hoses(vacuum) that are connected to the housing for reassembly. You'll need to "roll" the box out from under the dash depending on how much of the dash has been removed. The core is easy to spot for is has two hoses sticking out, and, is encircled with clips or screws . Also make sure you remove the bracket around the two entry hoses if it has one. Thank you, Dana

Posted on Oct 04, 2009

tripletauto
  • 1450 Answers

SOURCE: 1996 GMC Sonoma heater core

the dash has to come out

Posted on Sep 11, 2008

  • 275 Answers

SOURCE: trying to replace the serpentine belt on a 1995 gmc van

you will have to get ahold of a book for it or go to a junkyard and find one like yours and get the belt routing decal

Posted on Nov 12, 2008

alicantecoli
  • 22131 Answers

SOURCE: 1995 GMC Vandura wont start

try testing it manually first,pos of battery to solonoid ,did you put the bridge to windings back on?

Posted on Feb 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 GMC Vandura 2500 custom van. i need to know location and how to replace wiper motor


Make sure that's what you need because it's not a fun job.The wiper motor is under the dash above the gas pedal.Way up under the dash.Partial and/or full dash removal may be necessary.It depends on your skill level and determination! One heck of a great van to own!

Apr 28, 2017 | GMC Cars & Trucks

1 Answer

Why 1995 gmc vandura only blow hot air while driving but sitting still cold air


Low coolant level.... restriction in heater core or vacuum problem with hot/cold blend door would be what to look at. Worst case scenerio would be headgasket issue but unlikely

Nov 15, 2015 | GMC Cars & Trucks

1 Answer

1995 GMC Vandura 2500 5.0, 350 4L60-E trans


Try cleaning the grounds in the engine compartment to see if that helps. Clean the battery connections also.

Feb 18, 2014 | Cars & Trucks

1 Answer

1995 gmc vandura 2500 how do i fix to much play in steering


check and replace if necessary ...tie rod ends ....pitman arm ...idler arm ...posss steering box bad

Oct 27, 2013 | 1992 GMC Sonoma

1 Answer

Van won't start,rapid clicking heard when key is turned. need help/directions replacing starter relay for gmc vandura 2500, 1991


Check battery connections and battery fuse. Battery may not be large enough for the size of your van

Jan 18, 2013 | GMC Cars & Trucks

1 Answer

1995 GMC Vandura 2500 v-6 Van. A mechanic raised the idle way too high with a computer to test my van, but I just want to reset it back to factory specs and was told about a key off-on pattern that could...


Pull the ECM fuse out then put it back that will reset the computer.You can also take the ground cable off the battery for 30 seconds to reset the computer.If your engine still idles high afterwards then take the idle air control valve off and clean it with a non-chlronated brake cleaner and a wire brush.

May 06, 2011 | GMC V2500 Cars & Trucks

1 Answer

What's it called?


It would be called the engines accessory pulley mounting bracket

May 23, 2009 | 1987 GMC VanDura

1 Answer

Trying to replace the serpentine belt on a 1995 gmc van


you will have to get ahold of a book for it or go to a junkyard and find one like yours and get the belt routing decal

Nov 12, 2008 | GMC Vandura Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...